Single-molecule single crystals

Various approaches to the preparation and verification of single-molecule single crystals are discussed for polyethylene and poly (oxyethylene). Analytic tools are electron microscopy, electron diffraction, and differential scanning calorimetry. The main difficulty in producing a single-molecule single crystal is to keep crystals from joining during growth.     

Growth and optical properties of a new self-Q-switched laser crystal: Cr:Yb3Al5O12

Cr⁴⁺:YbAG (Cr⁴⁺:Yb₃Al₅O₁₂) crystal with a size up to Φ24 mm×30 mm was grown by the Czochralski method. In the absorption spectrum, there are two absorption bands at 939 and 969 nm, respectively, which are suitable for InGaAs diode laser pumping, and there is an absorption band at 1030 nm, which is suitable for passive Q-switched laser output at 1.03 μm. A broad emission spectrum from 970 to 1100 nm was exhibited from 940 nm wavelength pumping. This crystal is promising as a self-Q-switched laser crystal used for compact, efficient, highly stable, passive self-Q-switched thin chip solid-state lasers.     

Design aspects of planar and conventional SMPS transformer: a cost benefit analysis

The intent of this paper is to design a high-frequency transformer that is to be incorporated into the DC/DC pulsewidth-modulated switch-mode power supplies by two different technical approaches: a conventional wound-coil magnetic using copper wires, and a planar magnetic with layered copper tracks on laminated printed circuit board. Comparisons will be made between the two approaches in terms of profile: mounting height and surface area, and performance: power losses and efficiency. Other indicators like temperature rise and leakage inductance that causes electromagnetic interference, and cost, materials, and process fluency are also to be looked into. A sandwiched configuration for primary and secondary windings is proposed for the planar type. Issues arising and typical phenomena encountered will be discussed in detail. Primarily, the dominating factor in performance, cost effectiveness, or circuit compactness that restrains the choice of a particular type is to be evaluated.     

Broadband Light Source for Wavelength-Division Multiple Access Passive Optical Network

We demonstrated a unified two-band broadband light source based on erbium-doped fiber. The proposed scheme generates high output power at both bands and saves doped-fiber and pump lasers.     

Graphitic nanofillers in PMMA nanocomposites—An investigation of particle size and dispersion and their influence on nanocomposite properties

Mechanical, thermal, and electrical properties of graphite/PMMA composites have been evaluated as functions of particle size and dispersion of the graphitic nanofiller components via the use of three different graphitic nanofillers: “as received graphite” (ARG), “expanded graphite,” (EG) and “graphite nanoplatelets” (GNPs) EG, a graphitic materials with much lower density than ARG, was prepared from ARG flakes via an acid intercalation and thermal expansion. Subsequent sonication of EG in a liquid yielded GNPs as thin stacks of graphitic platelets with thicknesses of ～10 nm. Solution‐based processing was used to prepare PMMA composites with these three fillers. Dynamic mechanical analysis, thermal analysis, and electrical impedance measurements were carried out on the resulting composites, demonstrating that reduced particle size, high surface area, and increased surface roughness can significantly alter the graphite/polymer interface and enhance the mechanical, thermal, and electrical properties of the polymer matrix. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2097–2112, 2007     

Investigation on crosslinking behaviors of NBR/PVC filled with anhydrous copper sulfate particles by dynamic mechanical analysis

Crosslinking behaviors of acrylonitrile butadiene rubber (NBR)/poly (vinyl chloride) (PVC) alloy, filled with anhydrous copper sulfate (CuSO₄) particles, were investigated for the first time by dynamic mechanical analysis (DMA) under hetero and isothermal modes, respectively. In the heterothermal testing, (NBR/PVC)/CuSO₄ compound showed two marked increases in the storage modulus (E′), corresponding to coordination crosslinking of NBR-CuSO₄ and self-crosslinking of NBR and PVC respectively. During the isothermal testing, a dramatic increase in E′ was found at the initial stage while that of original NBR/PVC alloy was not detected. The marked increase in E′ of (NBR/PVC)/CuSO₄ compound was mainly due to the crosslinking induced by coordination between  CN and Cu²⁺. The increasing extent of E′ increased with the rise of CuSO₄ content, suggesting the formation of a greater number of crosslinks. Moreover, the activation energy (E_a) of crosslinking process was about 139 kJ/mol. In this work, fourier transform infrared spectrum (FT-IR) and equilibrium swelling method were also performed for the characterization of the compound. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 41–51, 2007     

线性复合片补偿器

本文给出一种特殊复合延迟片——复合片补偿器。改变入射线偏振光的振动方位角,便可改变补偿器的延迟量,调整简单,精度高。     

Spatial decay in a double diffusive convection problem in Darcy flow

This paper deals with a model of time-dependent double diffusive convection in Darcy flow. In particular it is concerned with the spatial decay of solutions when the flow is confined to a semi-infinite cylinder. Decay bounds for an energy expression are derived.     

On Donaldson’s flow of surfaces in a hyperkähler four-manifold

We prove some basic properties of Donaldson’s flow of surfaces in a hyperkähler 4-manifold. When the initial submanifold is symplectic with respect to one Kähler form and Lagrangian with respect to another, we show that certain kinds of singularities cannot form, and we prove a convergence result under a condition related to one considered by M.-T. Wang for the mean curvature flow.