A 1-V 10.7-MHz switched-opamp bandpass /spl Sigma//spl Delta/ modulator using double-sampling finite-gain-compensation technique

A 1 V switched-capacitor (SC) bandpass sigma-delta (/spl Sigma//spl Delta/) modulator is realized using a high-speed switched-opamp (SO) technique with a sampling frequency of up to 50 MHz, which is improved ten times more than prior 1 V SO designs and comparable to the performance of the state-of-the-art SC circuits that operate at much higher supply voltages. On the system level, a fast-settling double-sampling SC biquadratic filter architecture is proposed to achieve high-speed operation. A low-voltage double-sampling finite-gain-compensation technique is employed to realize a high-resolution /spl Sigma//spl Delta/ modulator using only low-DC-gain opamps to maximize the speed and to reduce power dissipation. On the circuit level, a fast-switching methodology is proposed for the design of the switchable opamps to achieve a switching frequency up to 50 MHz. Implemented in a 0.35-/spl mu/m CMOS process (V/sub TP/=0.82 V and V/sub TN/=0.65 V) and at 1 V supply, the modulator achieves a measured peak signal-to-noise-and-distortion ratio (SNDR) of 42.3 dB at 10.7 MHz with a signal bandwidth of 200 kHz, while dissipating 12 mW and occupying a chip area of 1.3 mm/sup 2/.     

The measurement of solar array discharges in a simulated spaceenvironment

A spacecraft in a plasma builds up charge on all the dielectric surfaces and interfaces. Once the net charge exceeds the dielectric breakdown of the material, a discharge occurs. One of the more susceptible pieces of equipment is the antenna/receiver system. The radiated E-field may be strong enough to create an ambiguous signal which may be misinterpreted by the system electronics and cause a system malfunction. A technique is developed to monitor the radiated E-field of materials discharging in an electron environment, using vacuum chambers for measuring the material discharges which are made of highly reflective materials. These chambers affect the radiated E-field due to multiple reflections from the walls. The technique developed defines a method for correcting the effects caused by the measurement facilities. The methodology is: monitor the radiated E-field with a broadband dipole antenna, and digitize the radiated signal as a function of time. Determine the frequency response of the radiated E-field using an FFT algorithm. Measure the transmission and reflection characteristics of the two-port network inside the measurement chamber, and determine the impedance network from the measured E-parameters across the frequency band of interest. Transform the measured E-field frequency response through the impedance network to obtain the frequency response of the actual radiated discharge current. Find the inverse FFT of this response to obtain the actual radiated discharge current response. This technique aids in the prediction of the E-field coupling into receive antennas on-board actual satellites     

Scattering from and penetration into a dielectric-filled conductingcylinder with multiple apertures

The theory of characteristic modes for aperture problems is used in this paper to solve the equivalent magnetic current and aperture fields due to a conducting cylinder with multiple slots. It is assumed that these slots are illuminated by either a transverse electric (TE) or a transverse magnetic (TM) plane wave and the media inside and outside the cylinder exhibit different electromagnetic properties. The formulation is given for the general case and numerical results for a limited number of slots are presented     

An optical instrumentation using a sensor with a sensordummyagainst noises on sensor and transmission line

This short paper discusses the method of effectively canceling equal status normal mode noise not only on a sensor line but also on a transmission line of an optical instrument using a sensor with a sensordummy resistance     

Crosstalk between microstrip transmission lines

Methods for prediction of crosstalk between microstrip transmission lines are reviewed and simplified for the weak-coupling case. Classical coupled transmission line theory is used for uniform lines, and potential and induced EMF methods are used for crosstalk between nonuniform lines. It is shown that the potential method is equivalent to classical coupled transmission line theory for the case of uniform lines. An experiment was performed for uniform coupled microstrip lines for frequencies from 50 MHz to 5 GHz, and good agreement between theory and measurement was obtained for both near- and far-end crosstalk     

Microscopic simulation of electronic noise in semiconductormaterials and devices

We present a microscopic interpretation of electronic noise in semiconductor materials and two-terminal devices. The theory is based on Monte Carlo simulations of the carrier motion self-consistently coupled with a Poisson solver. Current and voltage noise operations are applied and their respective representations discussed. As application we consider the cases of homogeneous materials, resistors, n⁺nn ⁺ structures, and Schottky-barrier diodes. Phenomena associated with coupling between fluctuations in carrier velocity and self-consistent electric field are quantitatively investigated for the first time. At increasing applied fields hot-carrier effects are found to be of relevant importance in all the cases considered here. As a general result, noise spectroscopy is found to be a source of valuable information to investigate and characterize transport properties of semiconductor materials and devices     

Suppression control method for torque vibration of three-phase HB-type stepping motor utilizing feedforward control

This paper proposes a method to reduce the vibration of the three-phase HB-type stepping motor with cogging torque by the feedforward compensation control. The compensation signal to suppress the vibration of the motor frame is obtained by the repetitive controller installing an online Fourier transformer and utilizing an acceleration sensor attached to the motor frame or an acoustic sensor such as a microphone placed close to the frame. The sensor is used only for the acquisition of the feedforward compensation data. The feedforward compensation signal at an arbitrary operating point is derived from the amplitude and phase data of the frequency components and the operating point data. Compensation data obtained by the repetitive controller is applied to the operating point changed by reference frequency and load condition in steady state. The compensation signal for the new operating point will be generated from compensation data utilizing polynomial equation approximation and linear interpolation method. The effectiveness of this proposed method is confirmed by the experimental results.     

Hybrid ARQ scheme employing TCM and packet combining

A new hybrid automatic repeat request scheme employing packet combining based on the Viterbi decoder is presented. It is shown that the proposed form of combining, together with a rearrangement of the signal constellation, can outperform similar forms of packet combining such as average diversity combining     

Voiced speech excitation synthesis using a sinusoidal model

A modification to the `shape-invariant' sinusoidal speech model is proposed, whereby the phases of the component sinewaves used for the excitation are made to add coherently at each glottal closure. Applied to pitch and time-scale modification, higher quality synthetic speech is produced when large changes are required