Systematic characterization of Cl2 reactive ion etchingfor improved ohmics in AlGaN/GaN HEMTs

Pre-metal-deposition reactive ion etching (RIE) was performed on an Al_0.3Ga_0.7N/AlN/GaN heterostructure in order to improve the metal-to-semiconductor contact resistance. An optimum AlGaN thickness for minimizing contact resistance was determined. An initial decrease in contact resistance with etching time was explained in terms of removal of an oxide surface layer and/or by an increase in tunnelling current with the decrease of the AlGaN thickness. The presence of a dissimilar surface layer was confirmed by an initial nonuniform etch depth rate. An increase in contact resistance for deeper etches was experienced. The increase was related to depletion of the two-dimensional (2-D) electron gas (2-DEG) under the ohmics. Etch depths were measured by atomic force microscopy (AFM). The contact resistance decreased from about 0.45 Ωmm for unetched ohmics to a minimum of 0.27 Ωmm for 70 Å etched ohmics. The initial thickness of the AlGaN layer was 250 Å. The decrease in contact resistance, without excessive complications on device processing, supports RIE etching as a viable solution to improve ohmic contact resistance in AlGaN/GaN HEMTs     

A comparison between different PMD compensation techniques

We quantify the benefits of using different techniques for compensation of polarization mode dispersion (PMD) in fiber-optic communication systems by means of numerical simulations. This is done both with respect to PMD-induced pulse broadening and in terms of system outage probability for different data formats [nonreturn-to-zero (NRZ) and return-to-zero (RZ)]. Attention is focused on simple and relevant single- and double-stage post-transmission compensators with a few degrees of freedom (DOF). It is generally believed that a PMD compensator with a polarization controller and a variable delay line can only compensate the PMD to the first order. We show, from analytical results, the counterintuitive fact that this scheme can also partially compensate for higher order PMD. We also investigate the benefit of using a polarizer as compensation element where the optical average power can be used as a feedback signal     

Efficient QoS support in a slotted multihop WDM metro ring

A novel distributed access protocol for a slotted wavelength-division-multiplexing (WDM) metro ring employing all-optical packet switching and supporting quality-of-service (QoS) classes is presented and analyzed. Since we assume that there are more nodes than available wavelengths in the network, we obtain a scalable multihop WDM ring as underlying network architecture. By dividing each channel into several time slots and further applying destination release and slot reuse, data packets can be efficiently transmitted and received in a statistically multiplexed manner. In our architecture, each node is equipped with one tunable transmitter and one fixed-tuned receiver. Furthermore, as we generally consider so-called a posteriori access strategies, different packet selection schemes are proposed and compared. An analytical model based on the semi-Markov process methodology is developed to quantify the performance of one of these schemes. As a key element of the protocol, an efficient QoS support access mechanism is proposed and its performance is evaluated. The new QoS control scheme adopts a frame-based slot reservation strategy including connection setup and termination, which only slightly increases the signaling and node processing overhead. Thus, an efficient hybrid protocol combining connectionless and connection-oriented packet transmissions is proposed     

Reliability prediction models to support conceptual design

During the early stages of conceptual design, the ability to predict reliability is very limited. Without a prototype to test in a lab environment or without field data, component failure rates and system reliability performance are usually unknown. A popular method for early reliability prediction is to develop a computer model for the system. However, most of these models are extremely specific to an individual system or industry. This paper presents three general procedures (using both simulation and analytic solution techniques) for predicting system reliability and average mission cost. The procedures consider both known and unknown failure rates and component-level and subsystem-level analyzes. The estimates are based on the number of series subsystems and redundant (active or stand-by) components for each subsystem. The result is a set of approaches that engineers can use to predict system reliability early in the system-design process. Software was developed (and is discussed in this paper) that facilitates the application of the simulation-based techniques. For the specific type of system and mission addressed in this paper, the analytic approach is superior to the simulation-based prediction models. However, all three approaches are presented for two reasons: (1) to convey the development process involved with building these prediction tools; and (2) the simulation-based approaches are of greater value as the research is extended to consider more complex systems and scenarios     

Mobility management for VoIP service: Mobile IP vs. SIP

Wireless Internet access has gained significant attention as wireless/mobile communications and networking become widespread. The voice over IP service is likely to play a key role in the convergence of IP-based Internet and mobile cellular networks. We explore different mobility management schemes from the perspective of VoIP services, with a focus on Mobile IP and session initiation protocol. After illustrating the signaling message flows in these two protocols for diverse cases of mobility management, we propose a shadow registration concept to reduce the interdomain handoff (macro-mobility) delay in the VoIP service in mobile environments. We also analytically compute and compare the delay and disruption time for exchanging signaling messages associated with the Mobile IP and SIP-based solutions.     

Microwave signal generation using an optical self-heterodyne technique

A new technique for mixing optical waves to generate microwave-frequency signals using an injection laser diode and a fibre-optic interferometer is reported. A beat signal is produced by interfering light from the laser with light from the same laser emitted earlier at a different frequency. The interferometer consists of an evanescent-field fibre coupler joined to a length of single-mode optical fibre. The laser is tuned by pulsed or bipolar current waveforms superimposed on a DC bias current. Feedback from an external cavity stabilises the laser frequency and reduces its linewidth. Efficient mixing at difference frequencies from 250 MHz to 2 GHz is obtained, with spectral widths of less than 1% of the centre frequency.     

High-Frequency Variations in the Rotation of the Earth

We report here observational results demonstrating that a three-station network of properly distributed VLBI observatories can routinely determine UT1 with a formal standard error of ±0.05 ms of time, in an observing period of 24 h. We also report the results of a three-month series of daily observing sessions of only 1-h duration with a single interferometer, which produced estimates of UT1 with standard errors of ±0.1 ms. The UT1 values obtained from the 1-h observing sessions track smoothly between the points of the 24-h time series, and the combined time series shows that it is not unusual for UT1 to vary by 1-2 ms in periods of several days. Preliminary results of reprocessing the 24-h observing sessions in 2-h segments suggest that variations of 0.4 ms may occur on time scales of only 6-8 h.