A novel driver assist stability system for all-wheel-drive electric vehicles

A novel driver-assist stability system for all-wheel-drive electric vehicles is introduced. The system helps drivers maintain control in the event of a driving emergency, including heavy braking or obstacle avoidance. The system comprises a fuzzy logic system that independently controls wheel torque to prevent vehicle spin. Another fuzzy wheel slip controller is used to enhance vehicle stability and safety. A neural network is trained to generate the required reference for yaw rate. Vehicle true speed is estimated by a sensor data fusion method. The intrinsic robustness of fuzzy controllers allows the system to operate in different road conditions successfully. Moreover, the ease of implementing fuzzy controllers gives a potential for vehicle stability enhancement.     

Low supply voltage high-performance CMOS current mirror with low input and output voltage requirements

This paper presents a scheme for the efficient implementation of a low supply voltage continuous-time high-performance CMOS current mirror with low input and output voltage requirements. This circuit combines a shunt input feedback and a regulated cascode output stage to achieve low input resistance and very high output resistance. It can be used as a high-precision current mirror in analog and mixed signal circuits with a power supply close to a transistor's threshold voltage. The proposed current mirror has been simulated and a bandwidth of 40 MHz has been obtained. An experimental chip prototype has been sent for fabrication and has been experimentally verified, obtaining 0.15-V input-output voltage requirements, 100-/spl Omega/ input resistance, and more than 200-M/spl Omega/ (G/spl Omega/ ideally) output resistance with a 1.2-V supply in a standard CMOS technology.     

RF microelectronics for W-CDMA mobile communication systems

Third generation (3G) mobile communication systems are now just starting to be introduced. With a maximum data rate of 2 Mbit/s they will make wireless access to broadband data services like the Internet or video applications feasible. Most of the different physical layer technologies summarised under the acronym 3G are based on wideband-CDMA (W-CDMA), in contrast to existing second generation systems, which mostly use TDMA and FDMA. This has severe consequences for the design of the transceiver front-ends. During standardisation these were assumed to have an adequate RF performance yet they still present a performance bottleneck for the system. Starting with a short introduction to UMTS (Universal Mobile Telecommunications System)-the 3G standard to be deployed in Europe and already operating in Japan-this paper describes by way of example some of the test cases specified for UMTS and their impact on the analogue front-end. It is shown that accurate simulation of all the analogue and digital signal processing is necessary in order to predict the RF performance needed of today's commercial RFICs. The paper then presents and reviews some actual design examples. Finally, possible technologies and techniques for application in future mobile terminals are discussed     

Physical Properties of Molten Salts in an Electron Donor–Acceptor Approach: The Density

It is found that the density (number of the component ion or molecule in 1 cm³) of a molten salt could be expressed as a function of the product of the electron donating and accepting properties of the component anion and cation. This equation is very useful for estimating the density of any molten salt at high temperature with the standard deviation accurately.     

Improvement in the DOA estimation of broadband signals usingpartially IIR beamformers

An ideal broadband beamformer requires an increased number of taps for each filter, which in turn increases the complexity of the design. It is shown that for angles near the broadside of the antenna the beamforming is more accurate compared to the angles near the endfire, and it is advantageous to use recursive filters combined with a computed number of zeros for angles near the endfire. The proposed method is used for estimating the arrival angle of the incoming signals and displays uniform accuracy for all angles     

Crosstalk between microstrip transmission lines

Methods for prediction of crosstalk between microstrip transmission lines are reviewed and simplified for the weak-coupling case. Classical coupled transmission line theory is used for uniform lines, and potential and induced EMF methods are used for crosstalk between nonuniform lines. It is shown that the potential method is equivalent to classical coupled transmission line theory for the case of uniform lines. An experiment was performed for uniform coupled microstrip lines for frequencies from 50 MHz to 5 GHz, and good agreement between theory and measurement was obtained for both near- and far-end crosstalk     

Correlation of modified crack tip opening distance with heat input to the heat affected zone of high-strength low-alloy steels

Investigated is the dependency of the crack tip opening displacement (CTOD) on the local microstructure of the heat affected zone in high-strength low-alloy (HSLA) microalloyed steel. Since the initiation of the crack tip location could not be controlled in fatigue, any possible correlation between heat iput in welding and fracture toughness could be smeared. Modified CTOD data are defined; they show that the fracture resistance of the weld joint decreased as the heat input increased.     

Diurnal and spatial variation of xylem dielectric constant in Norway Spruce (Picea abies [L.] Karst.) as related to microclimate, xylem sap flow, and xylem chemistry

Spatial and temporal variations in vegetation dielectric properties strongly influence the microwave backscatter characteristics of forested landscapes. This paper examines the relationship between xylem tissue dielectric constant, xylem sap flux density, and xylem sap chemical composition as measured in the stems of two Norway Spruce (Picea abies [L.] Karst.) trees in the Fichtelgebirge region of Northern Bavaria, Germany. Dielectric constant and xylem sap flux were monitored continuously from June through October 1995, at several heights along the tree trunks. At the end of the measurement series, each tree was harvested, and its xylem sap extracted and analyzed to determine the concentrations of amino acids and cations. Results show that the sap flux density was correlated with vapor pressure deficit (VPD) at all heights in the stem. In contrast, the xylem tissue dielectric constant is influenced by VPD but can exhibit a significant temporal lag relative to changes in VPD. This lag varies with position along the tree trunk. The temporal variability of the dielectric constant is compared with both trees at several positions along the tree trunks. Results of xylem sap chemical analysis are presented. We show that spatial and temporal variability in the xylem tissue dielectric constant is influenced not only by water content, but by variations in xylem sap chemistry as well. This has important implications for microwave remote sensing of forested landscapes, as useful information may be acquired regarding stand physiology and water relations and where variations in dielectric properties within individual trees and across geographic areas can be significant error sources for forest inventory mapping.     

Smooth Solution of the Compressible Navier–Stokes Equations in an Unbounded Domain with Inflow Boundary Condition

The barotropic compressible Navier–Stokes equations in an unbounded domain are studied. We prove the unique existence of the solution (u, p) of the system (1.1) in the Sobolev spaceH^{k + 3} × H^{k + 2}provided that the derivatives of the data of the problem are sufficiently small, wherek ≥ 0 is any integer. The proof follows from an analysis of the linearized problem, the solvability of the continuity equation, and the Schauder fixed point theory. Similar smoothness results are obtained for a linearized form of (1.1).