Plasma Enhanced Lithium Coupled with Cobalt Fibers Arrays for Advanced Energy Storage

Construction of high efficiency and stable Li metal anodes is extremely vital to the breakthrough of Li metal batteries. In this study, for the first time, groundbreaking in situ plasma interphase engineering is reported to construct high-quality lithium halides-dominated solid electrolyte interphase layer on Li metal to stabilize & protect the anode. Typically, SF₆ plasma-induced sulfured and fluorinated interphase (SFI) is composed of LiF and Li₂S, interwoven with each other to form a consecutive solid electrolyte interphase. Simultaneously, brand-new vertical Co fibers (diameter: ≈5 µm) scaffold is designed via a facile magnetic-field-assisted hydrothermal method to collaborate with plasma-enhanced Li metal anodes (SFI@Li/Co). The Co fibers scaffold accommodates active Li with mechanical integrity and decreases local current density with good lithiophilicity and low geometric tortuosity, supported by DFT calculations and COMSOL Multiphysics simulation. Consequently, the assembled symmetric cells with SFI@Li/Co anodes exhibit superior stability over 525 h with a small voltage hysteresis (125 mV at 5 mA cm⁻²) and improved Coulombic efficiency (99.7%), much better than the counterparts. Enhanced electrochemical performance is also demonstrated in full cells with commercial cathodes and SFI@Li/Co anode. The research offers a new route to develop advanced alkali metal anodes for energy storage.     

CuI Encapsulated within Single-Walled Carbon Nanotube Networks with High Current Carrying Capacity and Excellent Conductivity

High current carrying capacity and high conductivity are two important indicators for materials used in microscale electronics and inverters. However, it is challenging to obtain high conductivity and high current carrying capacity at the same time since high conductivity requires a weakly bonded system to provide free electrons, while high current carrying capacity requires a strongly bonded system. In this paper, CuI@SWCNT networks by filling the single-walled carbon nanotubes (SWCNTs) with CuI is ingeniously prepared. CuI@SWCNT shows good stability due to the confinement protection of SWCNTs. Through the host-guest hybridization, CuI@SWCNT networks exhibit a current carrying capacity of 2.04 × 10⁷ A cm⁻² and a conductivity of 31.67 kS m⁻¹. Their current carrying capacity and conductivity are significantly improved compared with SWCNT. The Kelvin probe force microscopy measurements show a drop of surface potential energy after SWCNT filled with CuI, indicating that the CuI guest molecules regulate the position of the Fermi level of SWCNTs, increasing carrier concentration, achieving high conductivity and high current carrying capacity. This study offers ideas and solutions for the regulation of high-performance carbon tube networks, which hold great promise for future applications in carbon-based electronic devices.     

Circularly polarized patch antenna with simultaneously wide frequency tuning range and high gain performance

A tunable circularly polarized square patch antenna with parasitic elements is designed for a wide frequency tuning range and high gain characteristics. The proposed antenna is constructed by one main patch and four semi-elliptic parasitic units. By loading four varactor diodes and adjusting their capacitance values, the tunable feature is performed to reallocate the corresponding working frequency. Moreover, the diagonal corners of the antenna are cut and loaded with varactor diodes, which provide the appropriate perturbation between the two orthogonality modes of the antenna, so as to ensure the circular polarization characteristic in the entire operating tuning band. The experimental results demonstrate that the reflection coefficient and axial ratio are less than −13 dB and 3 dB, respectively. The proposed antenna features a relatively wide continuously tuning range of 24% within 1.9-2.3 GHz and a stable gain of over 7 dBi with a radiation efficiency of above 85%.     

Passivating Defects of Perovskite Solar Cells with Functional Donor-Acceptor–Donor Type Hole Transporting Materials

In this study, a series of donor–acceptor–donor (D-A-D) type small molecules based on the fluorene and diphenylethenyl enamine units, which are distinguished by different acceptors, as holetransporting materials (HTMs) for perovskite solar cells is presented. The incorporation of the malononitrile acceptor units is found to be beneficial for not only carrier transportation but also defects passivation via Pb–N interactions. The highest power conversion efficiency of over 22% is achieved on cells based on V1359, which is higher than that of spiro-OMeTAD under identical conditions. This st shows that HTMs prepared via simplified synthetic routes are not only a low-cost alternative to spiro-OMeTAD but also outperform in efficiency and stability state-of-art materials obtained via expensive cross-coupling methods.     

Metal Micropatterning by Triboelectric Spark Discharge

Metal micropatterns play critical roles in flexible electronics. However, the lack of versatile strategies for micropatterning of diverse metal materials on various thin, flexible or stretchable substrates has limited the rapid development of flexible electronics. Here, a metal micropatterning method by triboelectric spark discharge under atmospheric environment is developed, where a triboelectric nanogenerator (TENG) is employed to precisely and safely control the voltage, current, and frequency of the spark discharges. Micropatterns of metal films like gold, silver, copper, aluminum and platinum are successfully fabricated on substrates of polyimide, polyethylene terephthalate, polyvinyl chloride, polydimethylsiloxane, paper or latex, even on ultrathin substrates (5 μm thick) without damage, where the feature sizes of metal patterns are controllable from 20 μm to 1 mm. Experimental insights into the triboelectric spark discharge behaviors and the pattern feature sizes control are discussed. A straightforward fabrication of metal patterns on the balloon surface or human skin through “handwriting” by a pencil as discharge electrode is realized. Besides metals, extended processibility of conductive materials like carbon nanotubes, graphene, MXene, graphite, carbon fibers, and conductive polymers are also demonstrated. This work proves the possibility of microfabrication by TENG, which is of simplicity and attractiveness for flexible electronics.     

偏最小二乘法在原子吸收光谱分析中的应用——钴和铟的同时测定

本文用偏最小二乘法（ＰＬＳ）校正了火焰原子吸收分析Ｉｎ２５２．１３７ｎｍ对Ｃｏ２５２．１３６ｎｍ的吸收线重叠干扰,对混合样中Ｃｏ和Ｉｎ的含量进行了测定,结果令人满意。