Applications of the finite difference techniques to the compensatedVIP 3 dB directional coupler

A new and simple compensated structure for a vertically installed planar (VIP) 3 dB directional coupler has been studied theoretically as well as experimentally by combining an improved 2-D-general finite difference (2-D-GFD) design procedure with a three-dimensional finite difference time domain (3-D-FDTD) method. The obtained full wave analysis results agree well with the measured ones. The investigations have shown that with this planar compensated structure, a better performance of the VIP coupler in the L-band can be realized by only using the same kind of dielectric substrate for its vertical and horizontal one     

A high-current and high-temperature 6H-SiC thyristor

A 6H-SiC thyristor has been fabricated and characterized. A forward breakover voltage close to 100 V and a pulse switched current density of 5200 A/cm² have been demonstrated. The thyristor is shown to operate under pulse gate triggering for turn-on and turn-off, with a rise time of 43 ns and a fall time of less than 100 ns. The forward breakover voltage is found to decrease by only 4% when the operating temperature is increased from room temperature to 300°C. It is found that anode ohmic contact resistance dominates the device forward drop at high current densities     

The effects of plasma etching induced gate oxide degradation onMOSFET's 1/f noise

The effects of the plasma etching process induced gate oxide damages on device's low frequency noise behavior are investigated on MOSFET's fabricated with different field plate perimeter to gate area ratio antennas. Abnormal 1/f noise spectrum with a shoulder centered in the frequency range of 100 and to 1 kHz was frequently observed in small geometry devices, and it is attributable to a nonuniform distribution of oxide traps induced by plasma etching process     

Sensitive monitoring of humic acid in various aquatic environments with acidic cerium chemiluminescence detection.

In this research, a simple, sensitive chemiluminescence (CL) method for the determination of humic acid (HA) in water samples was first developed based on the redox reaction between humic acid and cerium(IV) in the acidic condition. Different with the former redox CL reaction which occurred in alkaline solution, no enhancers were needed and neither precipitation nor a second contamination would occur in the present CL system. Comparing with other spectrometric methods, we find that the proposed analysis system had better applicability and accuracy. Under the optimal experiment conditions, the CL peak height was linear with the concentration of HA in the range of 0.03 to 10.0 microg mL(-1). The detection limit is 0.01 microg mL(-1) (S/N = 3), and the relative standard deviation was 2.3% for 0.5 microg mL(-1) HA solution with eleven repeated measurements. The present CL method was successfully applied to the determination of HA in tap water, spring water and river water samples with good recovery from 90.0 to 110.0%. A possible CL mechanism was proposed based on the results of UV and fluorescence spectrometry and the CL spectrum of HA. It was speculated that the semi-quinone radicals in the excited state were the emitters.     

Anchoring Properties of Nematic Liquid Crystals Studied Using the Attenuated Total Reflection Method

By using the attenuated total reflection method associated with the excitation of surface plasmons, the tilt angle of the liquid crystal director and its gradient at the surface are measured in a planar nematic cell as a function of the applied voltage. The surface anchoring anisotropy δπ of the liquid crystal and the surface elastic constant k_s, are found to be δπ = 0.288 erg/cm and k_s, = 9·12 × 10^-11 erg, respectively, when the boundary condition suggested by Barbero et al is used. The theoretical and experimental values obtained with this boundary condition and that of Mada are discussed. The results show that the boundary condition proposed by Barbero et al is in better agreement with the experiment.     

热载流子注入对MOS结构C─V和I─V特性的影响

讨论了热载流子注入对ＭＯＳ结构Ｃ─Ｖ和Ｉ─Ｖ特性的影响。指出热载流子效应引起载流子陷落和界面态的产生，导致Ｃ─Ｖ特性曲线畸变、平带电压漂移和恒定电压下ＳｉＯ２漏电流随时间漂移。本文论述了这些漂移的机理，提出了漂移的ｔｎ物理模型，从而很好地解释了实验所观察到的现象。     

石家庄市CATV系统网络技术指标分配初探

在ＣＡＴＶ系统网络工程设计中，技术指标的分配产关键问题。本文介绍了石家庄市在系统设计时采用的符合实际的设计程序，并对系统前端，传输及用户网各部分技术指标的确定，计算与分配方法，指标的核算等作了较详细地阐述，以供同行参考。     

Liquid crystalline hexa-amides and side chain polysiloxanes of azacrown [18]-N6

The hexa-4-dodecyloxybenzoyl derivative 1 of azacrown [18]-N₆ was originally reported to have a 'tubular' mesophase on the basis of its large central ring and 6-fold symmetry. Starting in the mesophase, annealing of 1 under a cover slip results in formation of a new crystalline phase that melts directly to an isotropic liquid at the temperature previously observed for the mesophase to isotropic transition. Thus the phase behaviour of 1 is kinetically controlled. The analogous hexa-3,4-bisdodecyloxybenzoyl derivative 2 of azacrown [18]-N₆ has no kinetic limitations to its phase changes and has an enantiotropic columnar liquid crystalline phase. We have synthesized side chain copolysiloxanes with a (CH₂)₁₁ spacer and 75-84 per cent by weight of the same 4-dodecyloxybenzoyl-[18]-N₆ mesogen. The polysiloxanes also display a liquid crystalline phase.     

DIGITAL PROCESSING OF THE POLARIZATION STATE OF GEOPHYSICAL ULF SIGNALS

In this paper, the evaluation by running window smoothing is used for the digital processing of the polarization of geophysical ULF signals. The observed signals are resolved into two orthogonal complex components so that it is no longer necessary to consider the phase and amplitude of the signals simultaneously.     

Comparisons of PWM and one-cycle control for power amplifier with multilevel converter

Based on the concepts of cascade multilevel converters and one-cycle technique, comparisons are conducted to characterize the distortion of the pulsewidth modulation (PWM) and one-cycle control methods that were applied to converters. Simulation results for the different control schemes are obtained in PSIM software initially to see the effect of one-cycle control different from that of PWM control. Through the comparisons, the advantages and disadvantages are identified for each method. The one-cycle scheme is better than PWM control in reducing undesirable harmonics and tracing dynamic waveforms. Simulation and experimental results are also provided to verify the conclusions.