Low-loss three-phase frequency conversion using a TDM-PWM technique

A strategy for the realisation of a product-modulation frequency conversion technique is presented. For maximum efficiency and spectral purity, a pulse-width modulation (PWM) circuit is used. The addition of pulse-width-modulated signals from the three input phases to each of the three output phases is accomplished by time-division multiplexing (TDM). The need for the product modulator to accommodate multiplication by negative numbers is eliminated by a modification to the basic equations.     

Signal generation and transmission at 40, 80, and 160 Gb/s using a fiber-optical parametric pulse source

Short return-to-zero pulses (/spl sim/2 ps) are generated at bit rates of 40, 80, and 160 Gb/s using a fiber-optical parametric amplifier. The performance of the parametric pulse source is evaluated both back-to-back and in a 110-km transmission link. A receiver sensitivity of -33 dBm back-to-back was achieved after demultiplexing from 160 to 10 Gb/s. The power penalty at 160 Gb/s due to 110-km transmission was less than 2 dB. Very short pulses (0.5 ps) were also achieved when using the parametric amplifier as a compressor.     

Uncooled DBR laser directly Modulated at 3.125 gb/s as athermal transmitter for low-cost WDM systems

An uncooled three-section tunable distributed Bragg reflector laser is demonstrated as an athermal transmitter for low-cost uncooled wavelength-division-multiplexing (WDM) systems with tight channel spacing. A /spl plusmn/0.02-nm thermal wavelength drift is achieved under continuous-wave operation up to 70/spl deg/C. Dynamic sidemode suppression ratio of greater than 35 dB is consistently obtained under 3.125-Gb/s direct modulation over a 20/spl deg/C-70/spl deg/C temperature range, with wavelength variation of as low as /spl plusmn/0.2 nm. This indicates that more than an order of magnitude reduction in coarse WDM channel spacing is possible using this source.     

Preservation of Lipschitz constants by Bernstein type operators

Summary We obtain preservation inequalities for Lipschitz constants of higher order in simultaneous approximation processes by Bernstein type operators. From such inequalities we derive the preservation of the corresponding Lipschitz spaces.     

Correlation between the Mechanical Properties and the Amount of Desorbed Water for Composites Based on Low-Density Polyethylene and Linen Yarn Production Waste

The effect of the amount of desorbed water on the mechanical properties of composites based on low-density polyethylene and linen yarn production waste (LW) is analyzed by statistical methods. It is shown that the amount of absorbed water decreases during the desorption process at room temperature both for specimens modified and unmodified with diphenylmethane diisocyanate (DIC.) The most sensitive to the action of water is the elastic modulus, which decreases considerably under the effect of water and is fully restored in the desorption process. The tensile strain also increases with the amount of absorbed water. It is found that the elastic modulus of the unmodified composite correlates linearly with the amount of desorbed water. Between the amount of desorbed water and the tensile strain, as well the specific work of deformation, a negative linear correlation is revealed. After water desorption, all strength and deformation characteristics of both the modified and unmodified composites are fully recovered.__________Translated from Mekhanika Kompozitnykh Materialov, Vol. 41, No. 4, pp. 515–524, July–August, 2005.     

Rietveld refinement of CdSe phases annealed under argon atmosphere

Hexagonal and cubic cadmium selenide were prepared from a chemical route by using cadmium chloride and potassium selenium hydride obtained from reaction of selenium powder and potassium boron hydride. The product obtained was thermally treated under argon flux at 300, 500 and 600 °C for 2 h and characterized by X-ray photoelectron spectroscopy and X-ray diffraction. The X-ray diffraction data were refined by Rietveld method and the structural parameters were determined for the phases of each annealed samples. At 300 °C five phases were identified: Cubic and hexagonal cadmium selenides and the contaminants: Potassium chloride, boron oxide and cadmium boron oxide. At 500 and 600 °C only the hexagonal cadmium selenide phase was identified besides the other above mentioned contaminant.     

Nanoclusteration of DNA with dendronized polymer in terms of free energy

A thermodynamic cycle for the nanoclusteration between DNA and dendronized polymer is proposed and electrostatic free energies of a series of DNA- dendronized polymer nanoclusteration processes are calculated. The free energies for assembling fixed charges and mobile ions, and the bending energies of the DNA chain wrapped around the dendronized polymer are taken into consideration. The free energies of nanoclusteration are calculated for a number of nanoclusters with different conformations at constant temperature and constant ionic strength. The effects of temperature and ionic strength on the free energy of nanoclusteration and stability of their conformations are also investigated.     

Low-Power VLSI Implementation of the Inner Receiver for OFDM-Based WLAN Systems

In this paper, we propose low-power designs for the synchronizer and channel estimator units of the Inner Receiver in wireless local area network systems. The objective of the work is the optimization, with respect to power, area, and latency, of both the signal processing algorithms themselves and their implementation. Novel circuit design strategies have been employed to realize optimal hardware and power efficient architectures for the fast Fourier transform, arc tangent computation unit, numerically controlled oscillator, and the decimation filters. The use of multiple clock domains and clock gating reduces the power consumption further. These blocks have been integrated into an experimental digital baseband processor for the IEEE 802.11a standard implemented in the 0.25mum- 5-metal layer BiCMOS technology from Institute for High Performance Microelectronics.