Inverted Solution Processable OLEDs Using a Metal Oxide as an Electron Injection Contact.

A new type of bottom‐emission electroluminescent device is described in which a metal oxide is used as the electron‐injecting contact. The preparation of such a device is simple. It consists of the deposition of a thin layer of a metal oxide on top of an indium tin oxide covered glass substrate, followed by the solution processing of the light‐emitting layer and subsequently the deposition of a high‐workfunction (air‐stable) metal anode. This architecture allows for a low‐cost electroluminescent device because no rigorous encapsulation is required. Electroluminescence with a high brightness reaching 5700 cd m^–2 is observed at voltages as low as 8 V, demonstrating the potential of this new approach to organic light‐emitting diode (OLED) devices. Unfortunately the device efficiency is rather low because of the high current density flowing through the device. We show that the device only operates after the insertion of an additional hole‐injection layer in between the light‐emitting polymer (LEP) and the metal anode. A simple model that explains the experimental results and provides avenues for further optimization of these devices is described. It is based on the idea that the barrier for electron injection is lowered by the formation of a space–charge field over the metal‐oxide–LEP interface due to the build up of holes in the LEP layer close to this interface.     

Effect of short glass fiber on structure and viscoelastic behavior of olefinic polymers synthesized with metallocene catalyst

Several composites were prepared on the basis of an ethylene homopolymer and different copolymers of ethylene and 1‐hexene, synthesized with a metallocene catalyst, as matrices and a content of a 5 wt % of short glass fiber. The effect of the fiber incorporation on the structure and mechanical and viscoelastic behaviors was analyzed for the different samples. The glass fibers induced a slightly higher crystallinity, and the crystallite morphology significantly changed (long spacings and crystal orientation). The incorporation of fibers did not reinforce the different matrices under study at this low content; consequently, the mechanical parameters, such as Young's modulus, yielding stress, and microhardness, were lower in the composites as compared with those values found in the neat polyolefins. The location and apparent activation energies of distinct relaxation processes are also discussed. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1244–1255, 2003     

A case of concomitant polymorphism and spontaneous resolution: the tetragonal phase of 5‐hydroxymethyl‐7,7,N‐trimethyl‐6‐oxabicyclo[3.2.1]octane‐1‐carboxamide

The title compound, C₁₂H₂₁NO₃, crystallizes in two polymorphic forms, viz. the tetragonal form described here and the monoclinic form described previously [Foces‐Foces, López‐Rodríguez, Pérez, Martín & Pérez‐Hernández (2007). Cryst. Growth Des. 7 , 905–911]. The differences in the conformations of the hydroxymethyl and methylaminocarbonyl substituents have important consequences in the hydrogen‐bond interaction motifs and, therefore, in the packing arrangements. These forms are concomitant polymorphs with melting points differing by 3 K.     

Effects of diamines and their fluorinated groups on the color lightness and preparation of organosoluble aromatic polyimides from 2,2‐bis[4‐(4‐amino‐2‐trifluoromethylphenoxy)phenyl]‐hexafluoropropane

To investigate the position and amount of the CF₃ group affecting the coloration of polyimides (PIs), we prepared 2,2‐bis[4‐(4‐amino‐2‐trifluoromethylphenoxy)phenyl]hexafluoropropane ( 2 ) with four CF₃ groups with 2‐chloro‐5‐nitrobenzotrifluoride and 2,2‐bis(4‐hydroxyphenol)hexafluoropropane. A series of soluble and light‐colored fluorinated PIs ( 5 ) were synthesized from 2 and various aromatic dianhydrides ( 3a – 3f ). 5a – 5f had inherent viscosities ranging from 0.80 to 1.19 dL/g and were soluble in amide polar solvents and even in less polar solvents. The glass‐transition temperatures of 5 were 221–265 °C, and the 10% weight‐loss temperatures were above 493 °C. Their films had cutoff wavelengths between 343 and 390 nm, b* values (a yellowness index) ranging from 5 to 41, dielectric constants of 2.68–3.01 (1 MHz), and moisture absorptions of 0.03–0.29 wt %. In a comparison of the PI series 6 – 8 based on 2,2‐bis[4‐(4‐aminophenoxy)phenyl]hexafluoropropane, 2,2‐bis[4‐(4‐amino‐2‐trifluoromethylphenoxy)phenyl]propane, and 2,2‐bis[4‐(4‐aminophenoxy)phenyl]propane, we found that the CF₃ group close to the imide group was more effective in lowering the color; this means that CF₃ of 5 , 7 , and 8f was more effective than that of 6c . The color intensity of the four PI series was lowered in the following order: 5 > 7 > 6 > 8 . The PI 5f , synthesized from diamine 2 and 4,4′‐hexafluoroisopropylidenediphthalic anhydride, had six CF₃ groups in a repeated segment, so it exhibited the lightest color among the four series. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 922–938, 2003     

A non‐linear and non‐local boundary condition for a diffusion equation in petroleum engineering

This article deals with a boundary value problem for Laplace equation with a non‐linear and non‐local boundary condition. This problem comes from petroleum engineering and is used to obtain an estimation of well productivity. The non‐linear and non‐local boundary condition is written on the well boundary. On the outer reservoir boundaries, we have both Dirichlet and Neumann conditions. In this paper, we prove the existence and uniqueness of a solution to this problem. The existence is proved by Schauder theorem and the uniqueness is obtained under more restricted conditions, when the involved operator is a contraction. Copyright © 2005 John Wiley & Sons, Ltd.     

Living/controlled radical copolymerization of N‐substituted maleimides with styrene in 1‐butyl‐3‐methylimidazolium hexafluorophosphate and anisole

The atom transfer radical copolymerization of N‐substituted maleimides such as N‐phenylmaleimide (PhMI), N‐cyclohexylmaleimide (ChMI), and N‐butylmaleimide (NBMI) with styrene initiated with dendritic polyarylether 2‐bromoisobutyrates in an ionic liquid, 1‐butyl‐3‐methylimidazolium hexafluorophosphate ([bmim][PF₆]), at room temperature and anisole at 110 °C was investigated. The dendritic‐linear block copolymers obtained in ionic liquid possessed well‐defined molecular weight and low polydispersity (1.05 < M_w/M_n < 1.32) and could be used as a macroinitiator for chain‐extension polymerization, suggesting the living nature of the reaction system. The ionic liquids containing catalyst could be recycled in the atom transfer radical polymerization systems without further treatment. Compared with polymerization conducted in anisole, the polymerization in ionic liquid had a stronger tendency for alternation. The tendency for alternation decreased in the order PhMI > NBMI > ChMI in [bmim][PF₆] and PhMI > ChMI > NBMI in anisole. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2156–2165, 2003     

Isolation and On‐Line LC/CD Analysis of 3,8″‐Linked Biflavonoids from Gnidia involucrata

Investigation of the methanol extract of the roots of Gnidia involucrata (Thymelaeaceae) led to the isolation and characterization of two new 3,8″‐biflavonoid diastereoisomers, named GB‐4 ( 6a ) and GB‐4a ( 6b ). Their absolute configurations were determined in mixture by on‐line LC/CD measurements, which also allowed the revision of absolute configurations of the biflavanoids GB‐1 and GB‐2, and the configurational assignment of GB‐3.     

Facile modifications of a polyimide via chloromethylation. I. Novel synthesis of a new photosensitive polyimide

A soluble aromatic polyimide was chloromethylated via a reaction with chloromethyl methyl ether in the presence of tin(IV) chloride to produce a new starting material for the modification of aromatic polyimides. The chemical structure of the resulting polymer was confirmed by ¹H NMR and Fourier transform infrared spectroscopy. The maximum number of chloromethyl groups per repeat unit was 1.81. The chloromethylated polyimide was stable up to 250 °C and soluble in both chloroform and tetrahydrofuran. So that its utilization for further modification could be demonstrated, cinnamic acid was reacted with the formed polyimide, and it produced a new photosensitive polyimide with a cinnamoyl side chain. The photosensitivity of the resulting polyimide was investigated with ultraviolet spectroscopic methods. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 22–29, 2003