Yb3+掺杂KY(WO4)2激光晶体生长、结构与光谱分析

采用顶部籽晶提拉法(TSSG)生长出Yb:KY(WO₄)₂(Yb:KYW)激光晶体.对预烧后的原料及晶体进行了XRD分析，结果表明，分别在920℃和600℃预烧8h后的熔质和助熔剂基本上形成一相，抑止了实验中的挥发问题；所生长的晶体为β-Yb:KYW，计算其晶格常数为a=1.063nm，b=1.034nm，c=0.755nm，β=130.75°.测得不同厚度样品的吸收光谱，结果表明样品在933nm和981nm有较强的吸收峰，计算出主峰981nm的吸收截面σ关键词： Yb:KYW TSSG法 晶体结构 光谱参数     

机载稳瞄控制系统模型及仿真分析

瞄准线高精度稳定是机载光电稳瞄系统的主要指标和关键技术。根据四框架稳瞄系统的工作原理，以手动跟踪模式为主要研究对象，建立了稳瞄伺服控制系统模型。考虑到直升机扰动特点，对线扰动、角速率扰动、摩擦力矩、弹性力矩等各种扰动因素也建立相应的数学模型，同时在各种扰动因素作用下利用Matlab对机载高精度稳瞄系统的手动跟踪控制模式进行了仿真设计分析和理论研究，设计出适合的控制器。此模型在实际系统中获得验证，对稳瞄伺服控制系统的设计具有参考意义。     

Synthesis and Reactions of Some New Pyrrolylfuro[2,3‐d]Pyrimidines and Pyrrolopyrazinofuropyrimidines

5‐Amino‐4‐methyl‐2‐phenyl‐6‐substitutedfuro[2,3‐d]pyrimidines ( 2a‐c ) were reacted with 2,5‐dimethoxytetrahydrfuran to afford the pyrrolyl derivatives 3a‐c . Compound 3a was chosen as intermediate for the synthesis of poly fused heterocycles incorporated furopyrimidines moiety 4–11 . Some of the synthesized compounds were screened for their antibacterial and antifungal activities.     

基于体全息技术的WDM器件

利用体全息技术制作波分复用器件是一种新方法。本文介绍了此种方法的基本原理和器件的基本性能，并报道了国外对该项技术的研究进展。     

电子束和接触式曝光机的混合曝光技术

Ⅰ线光致抗蚀剂可以同时实用电子束和光学系统曝光，在50kV加速电压下，其曝光剂量为50-100μC/cm^2，曝光后在0.7%NaOH溶液内显影1分钟。其灵敏度比PMMA快5倍，分辩率为0.5μm。采用两方法制备CaAsPHEMT：一种用Ⅰ线光致抗蚀剂，对源、漏及栅全部都采用电子束曝光，制备了0.5μm栅长的GaAs PHEMT；另一种将源、漏及栅分割成两部分，其中精细部分由电子束曝光，其余部分由光学系统曝光，用这种方法制备了0.25μm栅长的GaAs PHEMT。Ⅰ     

基于充放电原理实现的微电容测量电路

具有抗分布电容以及简单实用等特性的充放电电路是目前微电容测量中广泛采用的一种测量电路。本文对基于充放电原理的微电容测量电路进行了深入研究，并介绍一种基于充放电原理的实用电路。     

推广x重新标度模型的重标度参数经验公式

给出了推广x重新标度模型的重标度参数经验公式,其中建立了重标度参数与原子核的平均结合能之间的联系,由该公式可以得出A≥12的所有核的重标度参数值,利用这些参数值可以计算有关核过程并做出预言.     

Effect of misalignment on electrical characteristics of ACF joints for flip chip on flex applications

The effect of misalignment on the electrical properties of anisotropic conductive film (ACF) joints is investigated in this work. It is found that along with the increase of misalignment, the connection resistance of ACF joints increases. When the misalignment in x-direction is less than 5 μm, the increase rate of connection resistance is quite large. Then, along with the severity of misalignment, the increase rate becomes smaller. Finally, when the misalignment is close to 20 μm, the increase rate rises again. The Holm's electric contact theory is used for understanding the connection resistance variation. On the other hand, with the increase of misalignment in x-direction, the insulation resistance between ACF joints decreases. If the misalignment exceeded 10 μm, the decrease is prominent for the Ni particle ACF joints. This phenomenon can be explained by the effect of dielectric damage of the epoxy.Computer programs are also developed to calculate the variation of the probability of open and shorting after misalignment and predicate the maximum misalignment tolerance. The results show that the open and shorting probability increase abruptly after misalignment. On the view of pad parameters, the open probability is mainly related to the pad area, while the pads gap is critical to the shorting probability. Large pads gap (small pad width) can reduce the shorting probability obviously. On the other hand, enlarging the pad area by increasing pad length decreases the open probability significantly. So comparing to square shape pad, rectangle shape pad can reduce the failure probability greatly.