Reliability prediction models to support conceptual design

During the early stages of conceptual design, the ability to predict reliability is very limited. Without a prototype to test in a lab environment or without field data, component failure rates and system reliability performance are usually unknown. A popular method for early reliability prediction is to develop a computer model for the system. However, most of these models are extremely specific to an individual system or industry. This paper presents three general procedures (using both simulation and analytic solution techniques) for predicting system reliability and average mission cost. The procedures consider both known and unknown failure rates and component-level and subsystem-level analyzes. The estimates are based on the number of series subsystems and redundant (active or stand-by) components for each subsystem. The result is a set of approaches that engineers can use to predict system reliability early in the system-design process. Software was developed (and is discussed in this paper) that facilitates the application of the simulation-based techniques. For the specific type of system and mission addressed in this paper, the analytic approach is superior to the simulation-based prediction models. However, all three approaches are presented for two reasons: (1) to convey the development process involved with building these prediction tools; and (2) the simulation-based approaches are of greater value as the research is extended to consider more complex systems and scenarios     

Numerical solutions of the shallow water equations with discontinuous bed topography

A simple scheme is developed for treatment of vertical bed topography in shallow water flows. The effect of the vertical step on flows is modelled with the shallow water equations including local energy loss terms. The bed elevation is denoted with z_b^‐ for the left and z_b⁺ for the right values at each grid point, hence exactly representing a discontinuity in the bed topography. The surface gradient method (SGM) is generalized to reconstruct water depths at cell interfaces involving a vertical step so that the fluxes at the cell interfaces can accurately be calculated with a Riemann solver. The scheme is verified by predicting a surge crossing a step, a tidal flow over a step and dam‐break flows on wet/dry beds. The results have shown good agreements compared with analytical solutions and available experimental data. The scheme is efficient, robust, and may be used for practical flow calculations. Copyright © 2002 John Wiley & Sons, Ltd.     

Three ways to implement interfacial techniques: application tomeasurements of chromatic dispersion, birefringence, and nonlinearsusceptibilities

Depending on the spectal width of the source illuminating an interferometer, measurement procedures can utilize either the whole interferogram, or only the fringe envelope, or only the fringe quick oscillations. With an ultraband spectrum source, a simplified adaptation of the methods of Fourier transform spectroscopy yields the variations of the test-fiber propagation constant over the whole wavelength-interval of the source. Chromatic dispersion can then be computed from a single interferogram. With narrower spectrum sources, only the fringe envelopes are utilized and yield measurements of mode delay, with application to chromatic and polarization mode dispersion. In this case, however, interferograms at several wavelengths are necessary. With even narrower spectrum sources, the fringe quick oscillations provide measurements of phase shifts, related to changes in the mode propagation constant, when outside perturbations are applied to the test fiber. A direct method for measuring the third-order nonlinear susceptibilities is discussed. In this case the outside perturbation is an intense pump laser field     

Continuous phase quadrature phase shift keyed signaling techniquewith coding

A continuous phase quadrature phase shift keyed (CPQPSK) modulation technique is presented. This method utilizes a conventional QPSK modulator and a phase trajectory converter to approximate M=4, h=1/4 continuous phase signal and allows low cost, low complexity, and high rate (>1 Gbit/s) CPM modem implementation for bandwidth efficient transmission through nonlinear satellite channels. Using a communications analysis computer program it has been found that CPQPSK has 99 percent out-of-band power of 0.8R (MSK has 99 percent out-of-band power of 1.2 R where R is defined as bit rate), continuous phase trajectories, and nearly constant envelope amplitude. Simulation of realistic hardware designs indicate that the CPQPSK will require an Eb/No of 14 dB to achieve a bit error rate (BER) of 10^-6. Forward error correcting techniques using block codes with an overhead of 10 percent indicate that the Eb/No requirements can be reduced to 11.2 dB for 10^-6 BER     

Efficient computation of natural convection in a concentric annulus between an outer square cylinder and an inner circular cylinder

In this work, the natural convection in a concentric annulus between a cold outer square cylinder and a heated inner circular cylinder is simulated using the differential quadrature (DQ) method. The vorticity‐stream function formulation is used as the governing equation, and the coordinate transformation technique is introduced in the DQ computation. It is shown in this paper that the outer square boundary can be approximated by a super elliptic function. As a result, the coordinate transformation from the physical domain to the computational domain is set up by an analytical expression, and all the geometrical parameters can be computed exactly. Numerical results for Rayleigh numbers range from 104 to 106 and aspect ratios between 1.67 and 5.0 are presented, which are in a good agreement with available data in the literature. It is found that both the aspect ratio and the Rayleigh number are critical to the patterns of flow and thermal fields. The present study suggests that a critical aspect ratio may exist at high Rayleigh number to distinguish the flow and thermal patterns. Copyright © 2002 John Wiley & Sons, Ltd.     

Half-bridge inverter using 4H-SiC gate turn-off thyristors

This paper reports on the first demonstration of a half-bridge power inverter constructed from silicon carbide gate turn-off thyristors (GTOs) operated in the conventional GTO mode. This circuit was characterized with input bus voltages of up to 600 VDC and 2 A (peak current density of 540 A/cm²) with resistive loads using a pulse-width modulated switching frequency of 2 kHz. We discuss the implications of the thyristor's electrical characteristics and the circuit topology on the overall operation of the half-bridge circuit. This work has determined the conservative critical rate of rise value of the off-state voltage to be 200 V/μs in these devices     

Double-layer structural-acoustic coupling for cylindrical shell by using a combination of WDA and BIE

This work formulates the double-layer structural-acoustic coupling problem for cylindrical shell by using a combination of the wave-number domain approach (WDA) and the boundary integral equation (BIE). Expressions for the spectral radial velocity of the outer surface of a finite fluid-filled/submerged (FFS) cylindrical thin shell are formulated by means of the transfer matrix equation in wave-number domain. It is shown that the spectral variables on the inner surface of the shell are related to those on the outer surface of the shell. The far field sound radiation from this kind of shell is numerically evaluated for various fluid cases. An experimental verification is performed, and a good correlation between the theoretical results and the experimental results shows that the theoretical study work in this paper is correct.     

Semi‐analytical integration of the 8‐node plane element stiffness matrix using symbolic computation

The semi‐analytical integration of an 8‐node plane strain finite element stiffness matrix is presented in this work. The element is assumed to be super‐parametric, having straight sides. Before carrying out the integration, the integral expressions are classified into several groups, thus avoiding duplication of calculations. Symbolic manipulation and integration is used to obtain the basic formulae to evaluate the stiffness matrix. Then, the resulting expressions are postprocessed, optimized, and simplified in order to reduce the computation time. Maple symbolic‐manipulation software was used to generate the closed expressions and to develop the corresponding Fortran code. Comparisons between semi‐analytical integration and numerical integration were made. It was demonstrated that semi‐analytical integration required less CPU time than conventional numerical integration (using Gaussian‐Legendre quadrature) to obtain the stiffness matrix. © 2005 Wiley Periodicals, Inc. Numer Methods Partial Differential Eq, 2006