Mean vs. variance trade-off analysis in multi-antenna multi-user channels

In multi-user communications, the access point (AP) has several alternatives for distributing the scarce resources among users. Since there exists a trade-off between the global performance and the individual needs, an analytical framework to study fairness is derived, which completes the scope given by the existing fairness indexes in the literature. The framework proposed in this paper is a way to interpret fairness that has been inspired by portfolio selection; basically, it analyzes the mean vs. standard deviation trade-off. In this work, the target application is a multi-antenna AP transmitting simultaneously to several single-antenna terminals, although this framework is valid to analyze other procedures in multi-user communications.     

A tree partitioning dynamic policy for OVSF codes assignment in wideband CDMA

This paper proposes some novel techniques to accommodate users with different rate requirements in a wideband code-division multiple-access system employing orthogonal variable spreading factor codes. Two simple static code assignment strategies are first considered, and an improvement based on multicode assignment. Then the new idea of tree partitioning is introduced and used to devise a dynamic code reassignment algorithm. The behavior of these different techniques is experimentally investigated, in terms of call blocking probability and number of required reassignments. The tree partitioning method exhibits very good performances.     

Laterally coupled buried heterostructure high-Q ring resonators

All-buried InP-InGaAsP ring resonators laterally coupled to bus waveguides are demonstrated. The buried configurations offer a lower built-in refractive index step along the resonator periphery, which affords enhanced optical coupling coefficients between the waveguides and reduced scattering losses caused by the resonator sidewall imperfections. Very low optical intensity attenuations of 0.4 cm/sup -1/ and coupling-limited quality factors of greater than 10/sup 5/ are observed from 200-/spl mu/m-radii ring resonators. The measured spectral linewidth is as narrow as 0.0145 nm.     

On the Feasibility of Growing Pb[(Zn1/3Nb2/3)0.91Ti0.09]O3 Single Crystals

Pb[(Zn_1/3Nb_2/3)_0.91Ti_0.09]O₃ (PZNT91/9) single crystals were grown by two methods: from solution using PbO as a self‐fluxing agent (SC method) and directly from the melt without fluxing (MC method). In both growth methods, an allomeric Pb[(Mg_1/3‐Nb_2/3)_0.69Ti_0.31]O₃ (PMNT69/31) single crystal was used as a seed. X‐ray diffraction patterns of ground crystals showed that phase‐pure perovskite PZNT91/9 single crystals were successfully fabricated by the above two methods. The composition of the crystals obtained by both the SC and MC methods was analyzed using X‐ray fluorescence, which confirmed that the crystal composition is close to the nominal value, although volatilization of PbO and segregation during crystal growth are inevitable. The MC PZNT91/9 crystals exhibit excellent piezoelectric properties, with the piezoelectric constant, d₃₃, in the range of 1800–2200 pC N^–1. This value is comparable to that of the SC crystals. However, the MC crystals show an abnormal dielectric behavior. In contrast with the SC crystals, in the MC crystals a much broader dielectric peak appears in the dielectric response curves, accompanied by a much lower peak temperature of around 105 °C. Furthermore, frequency dispersion is apparent over a much wider temperature range (even more apparent than in pure relaxors), where a large, i.e., about 70 °C, full width at half maximum (FWHM) for the dielectric peaks is observed in the dielectric response. It is speculated that such an unusual phenomenon correlates with defects, microinhomogeneities, and polar regions in the as‐grown MC crystals. The origins of this abnormality have not been interpreted in detail until now. However, optical observation of the domain structure confirms that both the SC and MC crystals possess complex structural states.     

New design of hybrid-type self-bearing motor for small, high-speed spindle

A new structure of hybrid (HB)-type self-bearing motor is proposed for miniature spindle motors. The proposed design combines the HB-type self-bearing motor and HB active magnetic bearing in the common stator and rotor pair to generate large radial forces. First, the principle and theoretical background are introduced. Then, the air gap flux is analyzed by the finite element method, and radial forces for the proposed and standard-type HB self-bearing motors are compared. Finally, experiments are conducted to confirm the performance of the proposed motor. The motor can run at relatively high rotating speed with relatively high torque compared with its small size. The levitation is very stable and the motor indicates good performance for practical application.     

Fabrication of Schottky barrier MOSFETs using self-assembly CoSi2 nanopatterning and spacer gate technologies

A self-assembly patterning method for generation of epitaxial CoSi₂ nanostructures was used to fabricate 50 nm channel-length MOSFETs. The transistors have either a symmetric structure with Schottky source and drain or an asymmetric structure with n⁺-source and Schottky drain. The patterning technique is based on anisotropic diffusion of Co/Si atoms in a strain field during rapid thermal oxidation. The strain field is generated along the edges of a mask consisting of 20 nm SiO₂ and 300 nm Si₃N₄. During rapid thermal oxinitridation (RTON) of the masked silicide structure, a well-defined separation of the silicide layer forms along the edge of the mask. These highly uniform gaps define the channel region of the fabricated device. The separated silicide layers act as metal source and drain. A poly-Si spacer was used as the gate contact. The asymmetric transistor was fabricated by ion implantation into the unprotected CoSi₂ layer and a subsequent out-diffusion process to form the n⁺-source. I–V characteristics of both the symmetric and asymmetric transistor structures have been investigated.     

Measurements of small-scale fading and path loss for long range RF tags

RF modulated backscatter (RFMB), also known as modulated radar cross section or sigma modulation, is a RF transmission technique useful for short-range, low-data-rate applications, such as nonstop toll collection, electronic shelf tags, freight container identification and chassis identification in automobile manufacturing, that are constrained to have extremely low power requirements. The small-scale fading observed on the backscattered signal has deeper fades than the signal from a traditional one-way link of the same range in the same environment because the fading on the backscattered signal is the product of the fading on the off-board-generated carrier times the fading on the reflected signal. This paper considers the continuous wave (CW) type of RFMB, in which the interrogator transmitter and receiver antennas are different. This two-way link also doubles the path loss exponent of the one-way link. This paper presents the cumulative distribution functions for the measured small-scale fading and the measured path loss for short ranges in an indoor environment at 2.4 GHz over this type of link.     

Linear transformation shift registers

In order to exploit word-oriented operations for linear-feedback shift registers (LFSRs), Tsaban and Vishne [2002] introduced the notion of linear transformation shift registers (TSRs). An implementation of their primitive TSR generating algorithm shows that the LFSR are paired for all transformations. We prove that the characteristic polynomials of a pair of LFSRs are either both irreducible or both reducible for all transformations. This allows some time improvement when finding primitive TSRs. The authors give a full enumeration of all primitive TSRs with transformations of order 8 and LFSRs of order 3, 4, 5, and 6.     

On Faster I DDQ Measurements

The purpose of this paper is to introduce a new I _DDQ measurement technique based on active successive approximations, called ASA-I _DDQ. This technique has unique features facilitating a speed-up in I _DDQ measurement. Experimental results suggest that a significant speed-up factor (up to 4) can be obtained over the QuiC-Mon technique. Such a speed-up is a key element in the replacement of single-threshold I _DDQ testing since it amplifies the effectiveness of post-processing techniques.