Microscopic simulation of electronic noise in semiconductormaterials and devices

We present a microscopic interpretation of electronic noise in semiconductor materials and two-terminal devices. The theory is based on Monte Carlo simulations of the carrier motion self-consistently coupled with a Poisson solver. Current and voltage noise operations are applied and their respective representations discussed. As application we consider the cases of homogeneous materials, resistors, n⁺nn ⁺ structures, and Schottky-barrier diodes. Phenomena associated with coupling between fluctuations in carrier velocity and self-consistent electric field are quantitatively investigated for the first time. At increasing applied fields hot-carrier effects are found to be of relevant importance in all the cases considered here. As a general result, noise spectroscopy is found to be a source of valuable information to investigate and characterize transport properties of semiconductor materials and devices     

Suppression control method for torque vibration of three-phase HB-type stepping motor utilizing feedforward control

This paper proposes a method to reduce the vibration of the three-phase HB-type stepping motor with cogging torque by the feedforward compensation control. The compensation signal to suppress the vibration of the motor frame is obtained by the repetitive controller installing an online Fourier transformer and utilizing an acceleration sensor attached to the motor frame or an acoustic sensor such as a microphone placed close to the frame. The sensor is used only for the acquisition of the feedforward compensation data. The feedforward compensation signal at an arbitrary operating point is derived from the amplitude and phase data of the frequency components and the operating point data. Compensation data obtained by the repetitive controller is applied to the operating point changed by reference frequency and load condition in steady state. The compensation signal for the new operating point will be generated from compensation data utilizing polynomial equation approximation and linear interpolation method. The effectiveness of this proposed method is confirmed by the experimental results.     

An expert aid to fault diagnosis and trouble-shooting in satellitecommunications

Presents the Satellite Communications Network Expert (SaNE), a knowledge-based aid designed to provide engineering support for fault diagnosis. The SaNE is composed of two elements: a satcom network model, which simulates the structure and functionality of a system based loosely upon a large military satcom network, and a diagnostic component, which uses knowledge- and model-based reasoning techniques to analyse system anomalies and diagnose possible causes for the alarms such networks generate. The development cycle is described, emphasising lessons learnt during development and testing and the advantages and disadvantages of the techniques applied. The goal of the SaNE project is primarily commercial acceptance rather than innovation. The authors illustrate how novel concepts can be implemented in a practical system without compromising this goal     

FORECASTING MINERAL SUPPLY FROM MINERAL RENT DATA

An optimal control model of exhaustible resources is used to clarify the long run relationship between mineral rent and depletion cost at the industry level. A standard first order condition of the time rate of change of rents is reformulated to reveal that rent data may be used to help forecast the rise in extraction costs resulting from resource depletion. This application of the theory of exhaustible resources is illustrated using historical mineral industry rent and extraction cost data. A forecast of U.S. coal extraction costs, following the method proposed in this paper, suggests that future rates of extraction cost increases will be similar to rates experienced in the past.     

Very low threshold graded-indexseparate-confinement-heterostructure strained InGaAsPsingle-quantum-well lasers

A low threshold current density of ~100 A/cm² has been obtained at 1.55 μm using a graded-index separate-confinement-heterostructure strained InGaAsP single-quantum-well laser. The design of the laser structure is based on results calculated from the viewpoint of effective carrier injection into the well     

Design and performance evaluation of a banyan network basedinterconnection structure for ATM switches

This paper presents a new self-routing packet network called the plane interconnected parallel network (PIPN). In the proposed design, the traffic arriving at the network is shaped and routed through two banyan network based interconnected planes. The interconnections between the planes distribute the incoming load more homogeneously over the network. The throughput of the network under uniform and heterogeneous traffic requirements is studied analytically and by simulation. The results are compared with the results of the baseline network and another banyan network based parallel interconnection network. It is shown that, for the proposed design, a higher degree of heterogeneity results in better performance     

Optimal deterministic timeouts for reliable scalable multicast

Reliable multicast protocols suffer from the problem of feedback implosion. To avoid this problem, the number of receivers sending feedback in case of loss must be small. However, losses experienced by different receivers are strongly correlated, since receivers share common resources in the multicast tree. One approach to feedback implosion avoidance relies on delaying feedback at the receivers. We present deterministic timeouts for reliable multicast (DTRM), a distributed algorithm to compute optimal deterministic timeouts for each receiver in a multicast tree as a function of the tree topology and the sender-to-receiver round-trip delays. DTRM has several desirable properties. First, feedback implosion is provably avoided for a single loss anywhere in the tree, provided delay jitter is bounded. Second, the computation of the timeouts can be entirely distributed; receivers and intermediate nodes only rely on local topology information. Third, the timeouts computed by DTRM are optimal with respect to the maximum response time     

Finite element beam propagation method for three-dimensionaloptical waveguide structures

A beam propagation method (BPM) based on the finite element method (FEM) is described for longitudinally varying three-dimensional (3-D) optical waveguides. In order to avoid nonphysical reflections from the computational window edges, the transparent boundary condition is introduced. The present algorithm using the Pade approximation is, to our knowledge, the first wide-angle finite element beam propagation method for 3-D waveguide structures. To show the validity and usefulness of this approach, numerical results are shown for Gaussian-beam excitation of a straight rib waveguide and guided-mode propagation in a Y-branching rib waveguide     

Positive temperature dependence of the electron impact ionizationcoefficient in In0.53Ga0.47As/InP HBTs

Impact ionization is a major limiting factor to the maximum operating voltage of InGaAs-based, high-speed transistors. In this work, data on the positive temperature dependence of the electron impact ionization coefficient α_n in In_0.53Ga_0.47As at medium-low electric fields are reported for the first time. The increase of α_n with temperature is opposite to the behavior normally observed in most semiconductors. This anomalous behavior implies the onset of a positive feedback between power dissipation and avalanche generation which may adversely affect the power handling capability of In_0.53Ga _0.47As-based devices, and which should be taken into account in device thermal modeling. In the experimental procedure, based on the measurement of the multiplication factor M-1 in npn In_0.53Ga _0.47As/InP Heterojunction Bipolar Transistors (HBT), particular care has been taken in order to rule out possible spurious, temperature-dependent contributions to the measured multiplication current     

Densification involved in the UV-based photosensitivity of silicaglasses and optical fibers

A comprehensive survey of photosensitivity in silica glasses and optical fiber is reviewed. Recent work on understanding the mechanisms contributing to germanium or aluminum doped fiber photosensitivity is discussed within the framework of photoelastic densification models