两种方法制备ITO薄膜的红外特性分析

比较了用电束加热蒸发法和直流磁控溅射法制备的氧化锡铟(ITO)薄膜在红外波段的光学特性实验发现,通过直流磁控溅射在常温下制备的ITO薄膜在红外波段折射率稳定、消光系数小,比电子束加热蒸发制备的膜有较高的透过率在波长1550nm附近的透过率可达86%以上,消光系数约为004,方电阻最低为100Ω/□.     

无线局域网安全缺陷分析

本文介绍了Wi-Fi标准为解决无线局域网中的安全问题,相继采用的WEP、WPA、802．11i的方法,并分 析了这些方法可能存在的漏洞。同时,文中还进一步分析了VPN技术和入侵技术在无线局域网中的应用和存在的问题。 最后,介绍了我国无线局域网国家标准。     

Effects of B′-site transition metal on the properties of double perovskites Sr2FeMO6 (M=Mo, W): B′ 4d-5d system

The crystal structure, magnetic and magnetotransport properties of the variation of B′-site transition metal in Sr₂FeMO₆ (M=Mo, W) with double perovskites structure have been investigated systematically. Measurements of magnetization vs. temperature at H=5 T show that Sr₂FeMoO₆ is a ferromagnet and Sr₂FeWO₆ is an antiferromagnet with T_N∼35 K. Additionally, the large magnetoresistance ratio (MR) of ∼22% (H=3 T) at room temperature (RT) was observed in the Sr₂FeWO₆ compound. However, the Sr₂FeMoO₆ compound did not show any significant MR even at high fields and RT (MR∼1%; H=3 T and 300 K). The implications of these findings are supported by band structure calculations to explain the interaction between the 4d(Mo) and 5d(W) orbitals of transition metal ions and oxygen ions.     

稀土甘氨酸咪唑配合物[RE(Gly)4(Im)(H2O)](ClO4)3的热化学研究

采用溶解-反应量热法在具有恒温环境的溶解-反应热量计内,测定了[Gd(Gly)4(Im)(H2O)](ClO4)3和[Y(Gly)4(Im)(H2O)](ClO4)3两种稀土甘氨酸咪唑配合物的标准生成焓分别为(-3 461.46 ±0.22) kJ·mol-1 和(-3 926.6±0.90) kJ·mol-1.     

High photosensitivity in cis-polyphenylacetylene films irradiated with 60Co γ-ray

This paper reports that ⁶⁰Co γ-ray irradiation can convert cis-polyphenylacetylene (cis-PPA) films prepared with rare-earth coordination catalysts to highly photosensitive materials. The dependence of the photosensitivity on irradiation dose, preparation methods, and microstructure of the PPA films has been investigated by means of a potential discharge technique. The photosensitivity was enhanced with increasing irradiation dose. The critical dose to produce a light response was 5 × 10³ Gy. The maximum surface potential discharge rate was 618 V/s, and the dark decay was approximately 2 V/s for cis-PPA films irradiated with ⁶⁰Co γ-ray (dose: 2 × 10⁵ Gy). The cis-transoidal-PPA and an electrophotographic photoreceptor device incorporating cis-PPA showed a higher irradiation effect. The structure and properties of ⁶⁰Co γ-ray irradiated rare-earth PPA films are similar to the unirradiated films.     

即时通讯软件的安全性分析

在互联网服务中,即时通讯已成为了最流行的服务模式之一,人们对即时通讯的依赖程度也与日俱增。但是, 频频出现的病毒和黑客攻击使广大用户深受其害,即时通讯的安全问题也日益严峻。为了从根本上解决问题,本文对即时通讯软件的架构和协议进行了深入分析,目的是找出漏洞根源,给开发者和使用者提供防止漏洞的依据。     

基于双因子认证技术的网络身份识别

本文提出了一种基于动态双因子认证技术的网络身份识别方法,用户每次登录的口令是利用系统时间和用户ID通过MD5加密算法计算得到,其通过MD5加密后生成的登录口令是随机的,这将进一步提高开放网络环境下身份识别的可靠性和安全性。同时,本文还提出网络身份识别技术可以应用到各类网站的服务器上,用来完成对用户身份的识别,以提高网络系统的安全性。     

Broad-band MMICs based on modified loss-compensation method using 0.35-/spl mu/m SiGe BiCMOS technology

Using the concept of loss compensation, novel broad-band monolithic microwave integrated circuits (MMICs), including an amplifier and an analog multiplier/mixer, with LC ladder matching networks in a commercial 0.35-mum SiGe BiCMOS technology are demonstrated for the first time. An HBT two-stage cascade single-stage distributed amplifier (2-CSSDA) using the modified loss-compensation technique is presented. It demonstrates a small-signal gain of better than 15 dB from dc to 28 GHz (gain-bandwidth product=157 GHz) with a low power consumption of 48 mW and a miniature chip size of 0.63 mm² including testing pads. The gain-bandwidth product of the modified loss-compensated CSSDA is improved approximately 68% compared with the conventional attenuation-compensation technique. The wide-band amplifier achieves a high gain-bandwidth product with the lowest power consumption and smallest chip size. The broad-band mixer designed using a Gilbert cell with the modified loss-compensation technique achieves a measured power conversion gain of 19 dB with a 3-dB bandwidth from 0.1 to 23 GHz, which is the highest gain-bandwidth product of operation among previously reported MMIC mixers. As an analog multiplier, the measured sensitivity is better than 3000 V/W from 0.1 to 25 GHz, and the measured low-frequency noise floor and corner frequency can be estimated to be 20 nV/sqrt(Hz) and 1.2 kHz, respectively. The mixer performance represents state-of-the-art result of the MMIC broad-band mixers using commercial silicon-based technologies     

Children's cognitive function and cell-phone electromagnetic fields

Several companies have made major strides in marketing cellular telephones to children within the past 12 months; more and more children are using cell phones as part of their daily routines. Some fear any disturbance to brain activity in children could lead to impaired learning ability or behavioral problems. Moreover, any lasting biochemical effects could have important consequences, especially in the young, who still have years of development ahead of them. Recently, two studies of the mental process of young users of standard 902 MHz Global System for Mobile Communication (GSM) cellular mobile telephones were published: one paper reported a slight trend toward speeding up of simple reaction time, whereas the other study did not detect any change in cognitive functions.     

Silicon-to-steel bonding using rapid thermal annealing

This paper presents the rapid, low-temperature bonding between silicon and steel using the rapid thermal annealing process. Three different thin-film adhesion layer systems including silver, gold, and nickel were utilized as the intermediate bonding material to assist the eutectic Pb/Sn bonding between silicon and steel. The bonding temperature was set at 220/spl deg/C for 20 s, with a 20-s ramp-up time. Five experiments were conducted to determine the strength of the bond, including static tensile and compressive four-point bend tests, axial extension tests, tensile bending fatigue tests, and corrosion resistance tests. The test results have shown that the gold adhesion layer is the most robust, demonstrating minimal creep during fatigue tests, no delamination during the tensile or compressive four-point bend tests, and acceptable strength during the axial extension tests. Additionally, all adhesion layers have withstood four months of submersion in various high-temperature solutions and lubricants without failure. Simulations of the axial stresses and strains that developed during the four-point bend and axial extension tests were performed and showed that the presence of the silicon die provides a local reinforcement of the bond as observed in the experimental tests.