Dynamic RSVP protocol

RSVP is a resource reservation setup protocol that can be used by a host to request specific QoS for multicast multimedia flows on the Internet. Multiprotocol label switching (MPLS) architecture also needs RSVP. The fact that the resolutions of the display system used in different receiver nodes might have different, multi-resolution characteristics is supported in the MPEG-4 standard, and the EZW compression algorithm can cease decoding at any point in the bitstream. However, RSVP does not provide a more flexible mechanism. In this article we propose an extension of RSVP to provide the needed mechanism, coined dynamic RSVP (DRSVP), to dynamically adjust reserved resources on nodes without much effort. It provides different video resolutions to different receiver nodes with different needed reserved resources. Therefore, it does not waste precious Internet resources to transmit unnecessary multimedia packets.     

A novel technique for profiling the lateral n- dopingconcentrations of submicron LDD MOS devices

This paper reports a simple I-V method for the first time to determine the lateral lightly-doped source/drain (S/D) profiles (n^- region) of LDD n-MOSFETs. One interesting result is the direct observation of the reverse-short-channel effect (RSCE). It is observed that S/D n^- doping profile is channel length dependent if reverse short-channel effect exists as a result of the interstitial imperfections caused by Oxide Enhanced Diffusion (OED) or S/D implant. Not only the lateral profiles for long-channel devices but also for short-channel devices can be determined. One other practical application of the present method for device drain engineering has been demonstrated with a LATID MOS device drain engineering work. It is convincible that the proposed method is well suited for the characterization and optimization of submicron and deep-submicron MOSFETs in the current ULSI technology     

Accurate quasi-TEM spectral domain analysis of single and multiplecoupled microstrip lines of arbitrary metallization thickness

The quasi-TEM spectral domain approach (SDA) is extended to rigorously and efficiently analyze single and multiple coupled microstrip lines of arbitrary metallization thickness. The charge distributions on both the horizontal and vertical conductor surfaces are modeled by global basis functions. This results in a relatively small matrix for accurate determination of the line parameters of coupled thick microstrips. A convergence study is performed for the results of a pair of coupled lines with crucial structural parameters to explore the conditions for obtaining reliable solutions using the technique. Results for thick microstrips are validated through comparison with those from available measurements and another theoretical technique. The soundness of the technique is further demonstrated by looking into the trend of the results obtained by a simplified model in which the structural parameters are pushed, step by step, to the numerical extremities. Variations of circuit parameters of a four-line coupled microstrip structure due to the change of finite metallization thickness are presented and discussed     

Low-voltage BiCMOS dynamic minimum circuit using a parallelcomparison algorithm for fuzzy controllers

The authors present a low-voltage BiCMOS dynamic minimum circuit using a parallel comparison algorithm for VLSI implementation of fuzzy controllers. Using low-voltage BiCMOS dynamic circuits and a parallel comparison algorithm, a four-4-bit-input minimum circuit designed, based on a 1μm BiCMOS technology, shows a 9.5ns comparison time, which is a ×2.5 improvement in speed as compared to that based on CMOS technology     

Adaptive control of arterial blood pressure with a learningcontroller based on multilayer neural networks

The authors discuss a two-model multilayer neural network controller for adaptive control of mean arterial blood pressure (MABP) using sodium nitroprusside. A model with an autoregressive moving average (ARMA), representing the dynamics of the system, and a modified backpropagation training algorithm are used to design the control system to meet specified objectives of design (settling time and undershoot/overshoot) and clinical constraints. The controller is associated with a weighting-determinant unit (WDU) to determine and update the output weighting factor of the parallel two-model neural network for adequate control action and a control-signal modification unit (CMU) to comply with clinical constraints and to suppress the effect of adverse noise and to improve the WDU performance. Extensive computer simulations indicate satisfactory performance and robustness of the proposed controller in the presence of much noise, over the full range of plant parameters, uncertainties, and large variations of parameters     

Erbium-doped fiber amplifier second-order distortion in analog links and electronic compensation

The authors study the second-order distortion when an erbium-doped fiber amplifier (EDFA) is used to amplify the analog optical AM cable TV (CATV) multiple carrier signal from a directly modulated distributed feedback (DFB) semiconductor laser. Experimentally, it was seen that this second order distortion depends critically on the gain of the EDFA fiber amplifier. The authors attribute this distortion to the interaction between the frequency chirping of the DFB laser and the variable gain with wavelength of the amplifier. The authors describe an electronic predistorter that compensates the nonlinearity produced by the DFB-laser-EDFA combination. As a result, the high power advantage of the EDFA can be fully realized in spite of the potential for second-order distortion in the system.<>     

Single nucleotide polymorphism data analysis - State-of-the-art review on this emerging field from a signal processing viewpoint

The basic structural units of the genome are nucleotides. A single nucleotide polymorphism (SNP) is a mutation at a single nucleotide position. This paper discusses several major problems in SNP data analysis and review some existing solutions in this work. Generally speaking, a rich set of SNP analysis problems are cast in the signal processing framework. Our objective is to offer a state-of-the art review on this topic from a signal processing viewpoint so that researchers in the signal processing field can grasp the important domain knowledge to overcome the barrier between the two fields     

Dispersion Compensation in Externally Modulated Transmission System Using Chirped Fiber Grating

We present an externally modulated NTSC AM-VSB erbium-doped fiber amplifier (EDFA)-repeated system in the 1550 nm region which uses a chirped fiber grating (CFG) as a dispersion compensation device. In contrast to the conventional externally modulated fiber optical CATV systems, either with or without dispersion compensation fiber (DCF), good performances of carrier-to-noise ratio (CNR) ≥50 dB, composite second order (CSO) ≥74 dB, and composite triple beat (CTB) ≥65 dB were achieved for the full channel band after a 100-km single-mode fiber (SMF) transmission.     

A graphic approach to performance analysis of multistage linear interference canceller in long-code CDMA systems

The signal-to-interference-plus-noise-ratio performance of the multistage linear parallel and successive interference cancellers (LPIC and LSIC) in a long-code code-division multiple-access system is analyzed using a graphical approach. The decision statistic is modeled as a Gaussian random variable, whose mean and variance can be expressed as functions of moments of R for the LPIC and L for the LSIC, respectively, where R is the correlation matrix of signature sequences and L is the strict lower triangular part of R. Since the complexity of calculating these moments increases rapidly with the growth of the stage index, a graphical representation of moments is developed to facilitate the computation. Propositions are presented to relate the moment calculation problem to several well-known problems in graph theory, i.e., the coloring, the graph decomposition, the biconnected component finding, and the Euler tour problems. It is shown that the derived analytic results match well with simulation results.     

Fabrication and properties of PLZT ceramics from spray-dried aqueous solution

PLZT ceramics with the composition of 9/62/38 (La/Zr/Ti) were fabricated from spraydried aqueous solution. Complete crystallization of the spray-dried powder is achieved after 1 hr calcination at 650‡ C as compared to 800‡ C, 1 hr for conventional mixedoxide method. Sintering environment plays an important role in the densification of PLZT ceramics. Densities of the atmosphere sintered samples are much higher than those of normal sintered ones. PLZT ceramics derived from spray-dried powders have properties comparable to those derived from sol-gel ones. The spray-dried method presents a less expensive and more effective approach in the synthesis of PLZT ceramics.