Intermolecular Interactions and the Adhesion of Oleic Acid

The method presented by Good, van Oss, and Chaudhury was applied to characterize intermolecular interactions and the adhesion of oleic acid to selected model surfaces. Interfacial tensions of oleic acid were on the order 11–12 mJ/m² in aqueous solutions and 31–32 mJ/m² at air. The dispersive contribution to the surface tension of oleic acid against different neutral interfaces was determined to be 24–31 mJ/m² in air. Contact angles of oleic acid on selected hydrophilic and hydrophobic model surfaces were measured both in air and in aqueous solution. Van der Waals (dispersive) interactions determined the wetting properties of oleic acid in air both on nonpolar and basic surfaces. As expected, the adhesion of oleic acid to hydrophilic surfaces was much lower and to hydrophobic surfaces higher in aqueous environment than in air. The adhesion in aqueous environment is mainly governed by the cohesive and adhesive properties of water. It was concluded that the GvOC method in this case was only capable to give qualitative information about Lewis acid-base and van der Waals properties of surfaces and liquids, an important limiting factor being the asymmetry of oleic acid and the common probe liquids (diiodomethane and water).     

Titrimetric methods for the determination of surface and total charge of functionalized nanofibrillated/microfibrillated cellulose (NFC/MFC)

Total and surface charge of three different carboxymethylated nanofibrillated/microfibrillated cellulose (NFC/MFC) samples were investigated by using titrimetric methods (conductometric and polyelectrolyte (PE) titrations). Conductometric titration was found to be suitable method for the NFC total charge measurements when the back titration with HCl was applied. Surface charge measurements of NFC/MFC were conducted by using both indirect and direct PE titrations. The direct PE titration was found to be a more suitable method for the surface charge determination of NFC/MFC whereas the indirect PE titration produced too high surface charge values. This is presumably due to kinetically locked polyelectrolyte conformations on the NFC/MFC surfaces or entrapment of residual polymer after adsorption onto the NFC/MFC gel network. Finally, NFC was propargyl-functionalized and the changes in surface and total charge were successfully monitored and compared to those of propargyl-functionalized pulp. A good correlation between the titrimetric methods and elemental analysis was observed.     

All-cellulose multilayers: long nanofibrils assembled with short nanocrystals

Self-organized multilayer films were formed by sequential addition of oppositely charged cellulose I nanoparticles. The all-cellulosic multilayers were prepared via adsorption of cationicially modified cellulose nanofibrils (cat NFC) and anionic short crystalline cellulose (CNC) at pH 4.5 and pH 8.3. The properties and build-up behavior of layer-by-layer-constructed films were studied with microgravimetry (QCM-D) and the direct surface forces in these systems were explored with colloidal probe microscopy to gain information about the fundamental interplay between cat NFC and anionic CNC. The importance of the first layer on the adsorption of the consecutive layers was demonstrated by comparing pure in situ adsorption in the QCM-D with multilayer films made by spin coating the first cationic NFC layer and then subsequently adsorbing the following layers in situ in the QCM-D chamber. Differences in adsorbed amount and viscoelastic behavior were observed between those two systems. In addition, a significant pH dependence of cat NFC charge was found for both direct surface interactions and layer properties. Moreover the underlying cellulose layer in multilayer film was established to influence the surface forces especially at lower pH, where the cat NFC chains extensions were facilitated and overall charge was affected by the cationic counterpart within the layers. This enhanced understanding the effect of charge and structure on the interaction between these renewable nanoparticles is valuable when designing novel materials based on nanocellulose.     

Kinetics of elementary steps in the reactions of atomic bromine with isoprene and 1,3-butadiene under atmospheric conditions

Laser flash photolysis of CF(2)Br(2) has been coupled with time-resolved detection of atomic bromine by resonance fluorescence spectroscopy to investigate the gas-phase kinetics of early elementary steps in the Br-initiated oxidations of isoprene (2-methyl-1,3-butadiene, Iso) and 1,3-butadiene (Bu) under atmospheric conditions. At T ≥ 526 K, measured rate coefficients for Br + isoprene are independent of pressure, suggesting that hydrogen transfer (1a) is the dominant reaction pathway. The following Arrhenius expression adequately describes all kinetic data at 526 K ≤ T ≤ 673 K: k(1a)(T) = (1.22 ± 0.57) × 10(-11) exp[(-2100 ± 280)/T] cm(3) molecule(-1) s(-1) (uncertainties are 2σ and represent precision of the Arrhenius parameters). At 271 K ≤ T ≤ 357 K, kinetic evidence for the reversible addition reactions Br + Iso ? Br-Iso (k(1b), k(-1b)) and Br + Bu ? Br-Bu (k(3b), k(-3b)) is observed. Analysis of the approach to equilibrium data allows the temperature- and pressure-dependent rate coefficients k(1b), k(-1b), k(3b), and k(-3b) to be evaluated. At atmospheric pressure, addition of Br to each conjugated diene occurs with a near-gas-kinetic rate coefficient. Equilibrium constants for the addition/dissociation reactions are obtained from k(1b)/k(-1b) and k(3b)/k(-3b), respectively. Combining the experimental equilibrium data with electronic structure calculations allows both second- and third-law analyses of thermochemistry to be carried out. The following thermochemical parameters for the addition reactions 1b and 3b at 0 and 298 K are obtained (units are kJ mol(-1) for Δ(r)H and J mol(-1) K(-1) for Δ(r)S; uncertainties are accuracy estimates at the 95% confidence level): Δ(r)H(0)(1b) = -66.6 ± 7.1, Δ(r)H(298)(1b) = -67.5 ± 6.6, and Δ(r)S(298)(3b) = -93 ± 16; Δ(r)H(0)(3b) = -62.4 ± 9.0, Δ(r)H(298)(3b) = -64.5 ± 8.5, and Δ(r)S(298)(3b) = -94 ± 20. Examination of the effect of added O(2) on Br kinetics under conditions where reversible adduct formation is observed allows the rate coefficients for the Br-Iso + O(2) (k(2)) and Br-Bu + O(2) (k(4)) reactions to be determined. At 298 K, we find that k(2) = (3.2 ± 1.0) × 10(-13) cm(3) molecule(-1) s(-1) independent of pressure (uncertainty is 2σ, precision only; pressure range is 25-700 Torr) whereas k(4) increases from 3.2 to 4.7 × 10(-13) cm(3) molecule(-1) s(-1) as the pressure increases from 25 to 700 Torr. Our results suggest that under atmospheric conditions, Br-Iso and Br-Bu react with O(2) to produce peroxy radicals considerably more rapidly than they undergo unimolecular decomposition. Hence, the very fast addition reactions appear to control the rates of Br-initiated formation of Br-Iso-OO and Br-Bu-OO radicals under atmospheric conditions. The peroxy radicals are relatively weakly bound, so conjugated diene regeneration via unimolecular decomposition reactions, though unimportant on the time scale of the reported experiments (milliseconds), is likely to compete effectively with bimolecular reactions of peroxy radicals under relatively warm atmospheric conditions as well as in 298 K competitive kinetics experiments carried out in large chambers.     

Correlation of aluminum doping and lithiation temperature with electrochemical performance of LiNi1-xAlxO2 cathode material

Journal of Solid State Electrochemistry - This article presents a process for producing LiNi1-xAlxO2 (0 <  ×  < 0.05) cathode material with...     

Rapid estimation of chemical kinetics by implicit calibration. II

This study continues the development of a method, implicit calibration, for estimating kinetic parameters from on-line measurements of batch reactions. The basic idea of implicit calibration is to combine non-linear parameter estimation with the calibration of measured spectra with concentrations calculated by an assumed kinetic model. A new example is studied, an esterification reaction with a rather complicated kinetic mechanism, where activities, instead of concentrations, and NIR spectra are used as measurements. The emphasis in the study is on estimating the uncertainty of the kinetic parameters. Two approaches, linearization and bootstrap, are applied. In the case studied, the two approaches give closely similar estimates of the uncertainty. As well, a new way is introduced to control the rigidity of the implicit calibration, based on minimizing the lack of fit of the model. It is also shown that ‘mixed implicit calibration’, i.e. implicit calibration combined with a few off-line calibrated concentrations, greatly enhances the identifiability of the kinetic model. Copyright © 2003 John Wiley & Sons, Ltd.     

Polymerization of ethylene with new diimine complexes of late transition metals

Three pyridylimine based complexes of Ni^II and Co^II were reacted with methylaluminoxane (MAO) and tested as catalysts in ethylene polymerization. The two nickel catalysts produced mainly methyl branched polymers with good to moderate activity, while the cobalt compound showed only marginal activity. Reaction conditions strongly affect the polymer properties, such as molecular weight, melting temperature, degree of branching, and chain end unsaturation type.