Melt rheology of polylactide/montmorillonite nanocomposites

In this article, the linear and nonlinear shear rheological behaviors of polylactide (PLA)/clay (organophilic‐montmorillonite) nanocomposites (PLACNs) were investigated by an Advanced Rheology Expanded System rheometer. The nanocomposites were prepared by master batch method using a twin‐screw extruder with poly(ε‐caprolactone) (PCL) as a compatibilizer. The presence of org‐MMT leads to obvious pseudo‐solid‐like behaviors of nanocomposite melts. The behaviors caused by the formation of a “percolating network” derived from the reciprocity among the strong related sheet particles. Therefore, the storage moduli, loss moduli, and dynamic viscosities of PLACNs show a monotonic increase with MMT content. Nonterminal behaviors exists in PLACNs nanocomposites. Besides the PLACNs melts show a greater shear thinning tendency than pure PLA melt because of the preferential orientation of the MMT layers. Therefore, PLACNs have higher moduli but better processibility compared with pure PLA. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 3189–3196, 2007     

Bis[μ‐1‐(1,10‐phenanthrolin‐2‐yl)‐2‐pyridone]bis{aqua[1‐(1,10‐phenanthrolin‐2‐yl)‐2‐pyridone]cadmium(II)} tetrakis(perchlorate)

In the title centrosymmetric binuclear complex, [Cd₂(C₁₇H₁₁N₃O)₄(H₂O)₂](ClO₄)₄, the Cd^II ion assumes a distorted octahedral geometry. There are π–π stacking interactions between the pyridine and 1,10‐phenanthroline ring systems of adjacent ligands at the same Cd^II centre. Intermolecular hydrogen bonds between the coordinated aqua ligand and the O atom of a keto group connect adjacent complex cations into extended chains. Hydrogen bonds also exist between the complex cations and the perchlorate anions. Compared with the fluorescence spectrum of the organic ligand, the complex displays strong fluorescent emission and an ipsochromic shift of the emission peaks, which may be attributed to the structural character.     

微型网状结构支架的力学性能研究

冠状动脉支架为圆柱形微型网状结构，直径1mm，厚度0．1mm，长度10～16mm。在经皮冠状动脉介入PCI治疗中由球囊充气撑开到直径为2．5～3．5mm的支架，在血管内承受血管壁回弹压力。为了保持血液流通支架必须保持其几何圆形。这是一个结构弹塑性稳定性问题。但是目前国际上对于支架的力学性能质量指标主要以强度性能评定而不涉及支架屈曲性能是不妥的。本文对于支架的强度和屈曲性能进行了全面的理论分析和实验研究，自行研制了智能式电子检测仪成功地对微型网状结构支架的强度和屈曲性能实现了实测实验研究。由于微型支架的离散型网状结构的特点，在实验中出现一些特殊的屈曲现象。本文研究结果对于支架的形状与性能设计的改进和力学性能质量标准规范的制订具有重要意义。     

一类非线性弹簧振子的周期性振动

本文用数值计算的方法讨论了一类非线性弹簧振子的周期性振动及其特点．     

Radiative lifetimes of Rydberg states of BeⅠ and BeⅢ

By using the multichannel quantum defect theory(MQDT),we have evaluated the energy levels and lifetimes of 2sns ^3 S1,2snd ^3D(n=3-25)of BeI and 1 sns ^3s1,1snd ^3D(n=3-25)of BeⅢ,These energies and lifetimes that we have calculated not only agree with the recent measurements and theoretical calculation of Ref.4 and Ref.3, but also predict the lifetimes of 66 other highly excited states.     

Selected-area growth of carbon nanotubes by the combination of focused ion beam and chemical vapor deposition techniques.

In this article, we report a technique for growing carbon nanotubes in a more controllable fashion, which enables us to synthesize nanotubes directly in various forms of designed patterns. This nanofabrication process is based on a combination of focused ion beam (FIB) and chemical vapor deposition (CVD) techniques. In this process, arrays of conductive patterns were first deposited on silicon substrates by directing a gaseous compound (C(9)H(16)Pt) via the capillary needle-sized nozzles within a FIB system. The substrates were then coated with catalyst and further modified by the FIB to localize the position of the catalyst. Finally, the growth of carbon nanotubes on the designed substrates was carried out by CVD of hydrocarbon gases. This fabrication technique has the advantage of positioning carbon nanotubes in selected locations. This may open up opportunities for the direct synthesis of carbon nanotubes onto almost any substrate material, thus allowing fabrication of carbon nanotube-based devices.     

Properties of diode laser pumps for high-power solid-state lasers

Diode lasers used to pump high average power solid-state lasers typically have broad spectral width so that most of the pump light is not at the peak of the gain medium's absorption feature. However, the long absorption length in these lasers enables even weakly absorbed light to pump efficiently. The result is that high absorption efficiency and improved pump distribution uniformity are possible when using realistic pump diodes. In addition, both quantities are nearly independent of the pump center wavelength.     

KxCoO2·yH2O(x《0.2,y≤0.8)的晶体结构、输运及磁学性质

利用熔融KOH和Co3O4在较低温度(480℃)下反应制备出K0.36CoO2,然后用高锰酸钾溶液和饱和的过硫酸钾溶液进行氧化处理.氧化的同时伴随有水分子嵌入.K0.36CoO2用高锰酸钾和过硫酸钾溶液处理后分别得到K0.12CoO2·0.8H2O和K0.16CO2·0.6H2O.这两种化合物都属于六角晶系,表现出金属行为,脱水后主相变为正交结构并且呈现出半导体特性.K0.16CoO2·0.6H2O在56K附近可能存在自旋玻璃转变行为或其他涨落.随着钾含量的减少和水含量的增多,样品的自旋玻璃行为受到抑制或发生磁性相分离.样品K0.12CoO2·0.8H2O在零场冷却和有场冷却曲线上的分叉现象基本上消失.还讨论了产生KxCoO2与NaxCoO2体系结构和物性差别的原因.     

35Cr25Ni12奥氏体耐热钢中碳化物的电子显微分析

应用扫描电镜（SEM）和透射电镜（TEM）研究了长期使用前后的35Cr25Ni12奥氏体耐热钢中的碳化物演变行为；该钢固溶时效后的组织由初晶奥氏体及M23C6共晶碳化物组成，奥氏体基体中析出了二次M23C6，二次碳化物总是与基体保持立方－立方取向关系；长期使用（3、5年）后，奥氏体中析出的二次碳化物量明显增加，部分M23C6已转变为M6C，M6C与奥氏体基体以及二次碳化物M23C6保持[001]M6C//[221]A//[221]M23C6孪晶取向关系。     

Stationary Intensity Distribution of Single-Mode Laser Driven by Additive and Multiplicative Colored Noises with Colored Cross-Correlation

Applying the approximate Fokker-Planck equation we derived, we obtain the analytic expression of thestationary laser intensity distribution Pst(Ⅰ) by studying the single-mode laser cubic model subject to colored cross-correlation additive and multiplicative noise, each of which is colored. Based on it, we discuss the effects on the stationarylaser intensity distribution Pst(Ⅰ) by cross-correlation between noises and “color“ of noises (non-Markovian effect) whenthe laser system is above the threshold. In detail, we analyze two cases: One is that the three correlation-times (i.e.the self-correlation and cross-correlation times of the additive and multiplicative noise) are chosen to be the same value(τ1 = τ2 = τ3 = τ). For this case, the effect of noise cross-correlation is investigated emphatically, and we detect thatonly when λ≠ 0 can the noise-induced transition occur in the Pst(Ⅰ) curve, and only when τ≠ 0 and λ≠ 0, can the“reentrant noise-induced transition“ occur. The other case is that the three correlation times are not the same value,τ1 ≠τ2 ≠τ3. For this case, we find that the noise-induced transition occurring in the Pst (Ⅰ) curve is entirely differentwhen the values of τ1, τ2, and τ3 are changed respectively. In particular, when τ2 (self-correlation time of additivenoise) is changing, the ratio of the two maximums of the Pst(Ⅰ) curve R exhibits an interesting phenomenon, “reentrantnoise-induced transition“, which demonstrates the effect of noise “color“ (non-Markovian effect).