Site‐specific reversible immobilization and purification of His‐tagged protein on poly(2‐acetamidoacrylic acid) hydrogel beads

Ni²⁺‐complexed poly(2‐acetamidoacrylic acid) (PAAA) hydrogel beads were developed for the site‐specific reversible immobilization and purification of the histidine‐tagged green fluorescent protein (His‐tagged GFP). PAAA hydrogel beads were prepared by photopolymerization, and significantly improved mechanical properties of PAAA hydrogel beads were observed in comparison with PAAA hydrogel from our previous study. Confocal laser scanning microscopy was used to determine the binding of His‐tagged GFP to the hydrogel beads in three‐dimensional space. Photoluminescence spectroscopy revealed 89% of binding efficiency of His‐tagged GFP to the Ni²⁺‐PAAA hydrogel beads, 51% of yielding recovery. The maximum binding capacity of His‐tagged GFP was estimated to be 0.45 µg/mg of Ni²⁺‐PAAA hydrogel beads. The recombinant His‐tagged GFP from the soluble fraction of E. coli BL21(DE3) cell lysates was purified with Ni²⁺‐PAAA hydrogel beads. The major advantage of the Ni²⁺‐PAAA hydrogel beads system was simple preparation procedures of producing the matrix, because PAAA hydrogel beads had relatively enhanced mechanical strength than soft hydrogels. Copyright © 2012 John Wiley & Sons, Ltd.     

Air Oxidation of N-Cyclopropylanilines

Air oxidation of N-cyclopropylanilines was shown to occur under either ambient conditions or accelerated conditions (warming or shining light) in an open container. A subsequent fragmentation resulted in formation of the corresponding acetamide. While potential mechanisms have been previously proposed, simple aerobic oxidation to β-hydroxy-propionamides in the absence of a radical promoter has not been previously reported.     

Investigation on the dissolution of Mn ions from LiMn2O4 cathode in the application of lithium ion batteries: First principle molecular orbital method

The dissolution phenomenon of Mn ions in LiMn₂O₄ (LMO) cathode material for lithium ion batteries (LIBs) was investigated by a first principle calculation using the discrete variational Xα molecular orbital method. It was found that the oxidation number of Mn ions easily increases at high temperatures due to the empty levels of Mn 3d orbitals located in the vicinity of the Fermi energy level of LMO crystal. The changes of density of states (DOS) and Mn‐O bonding properties with doping were examined. Analysis of DOS showed that the substitution of elements with a smaller oxidation number than Mn was found effective in keeping Mn ions at higher oxidation states. From the calculation of bonding properties, the dissolution of Mn was found to be strongly correlated with the covalent nature of Mn‐O bond. Based on the results, we concluded that increasing the covalent character of Mn‐O bond is effective to minimize the dissolution of Mn ions, along with suppressing the formation of Jahn‐Teller‐active Mn³⁺ by inducing Mn ions at high oxidation state with proper selection of doping elements. © 2012 Wiley Periodicals, Inc.     

Significant change in water contact angle of electrospray‐synthesized SiO2 films depending on their surface morphology

Amorphous SiO₂ films were deposited by means of an electrospray technique. The relation between the water contact angle (WCA) of the deposited SiO₂ films and the surface morphology is investigated. The feeding rate of the electrospray process greatly affects the morphology of the synthesized SiO₂ films. There is also a significant change in the WCA on the surface of the films: the rougher the surface, the greater the WCA. A model based on the Cassie–Baxter formulation is used to explain the change observed in the WCA on the SiO₂ films. Copyright © 2012 John Wiley & Sons, Ltd.     

Biodegradable Cellulose Block Copolymers

Biodegradable polymers can be prepared by the incorporation of cellulose oligomeric blocks into the polymer backbone. Block copolymers prepared by reacting equimolar amounts of depolymerized cellulose triacetate (CTA) with MDI or TDI and block terpolymers prepared by reacting the CTA oligomer with poly (propylene glycol) capped with MDI or TDI were deacetylated and incubated with cellulysin at pH 5 and 50 °C. The intrinsic viscosity of each copolymer decreased substantially even after 10 hr incubation time. There was negligible acid hydrolysis. Cellulose showed a smaller decrease at the same incubation time-probably due to its lower accessibility. Methods for incorporating cellulose oligomeric blocks and other biodegradable blocks into different types of polymers are discussed.     

Controlled Activity Polymers. IV. Copolymers of 2-(1-Naphthylacetyl)Ethyl Acrylate With Hydrophilic Comonomers: Synthesis and Characterization

2-(1-Naphthylacetyl)ethyl acrylate (NAEA) was synthesized by esterification of 1-naphthylacetic acid (NAA) and 2-hydroxyethyl acrylate (HEA) and then polymerized to obtain the polymer-bound auxin NAA. The resulting polymer is potentially useful as a plant growth regulator through hydrolytic release of NAA. Copolymers of NAEA with hydrophilic comonomers were prepared by solution polymerization. The copolymer compositions were determined from elemental analysis, ¹³C-NMR, and UV spectroscopy. The copolymer microstructure was predicted from the reactivity ratios in order to investigate the influence on the behavior of controlled release. These model structures will be utilized for assessment of structure/hydrolysis relationships in a subsequent paper.