一种宽带矢量调制器的设计及其应用

矢量调制器是一种可以同时控制微波信号幅度和相位的器件。本文介绍了一种基于新型微带定向耦合器的宽带矢量调制器。新的耦合器结构克服了传统微带耦合器耦合度低、方向性差的问题,也不需要Lange耦合器复杂的加工工艺,在平衡放大器、移相器和衰减器等场合具有广泛的应用。其次,研究了用串联电感对衰减器中PIN二极管的寄生参数进行补偿的一种简单方法,以改善衰减器衰减量变化时的相位性能。该方法原理简单,可在一定带宽内替代复杂的平衡结构,并给出相近的性能。最后给出了矢量调制器的测试结果和它在自适应天线阵等实际系统中的应用情况,并讨论了用于提高载波和边带抑制、满足高精度要求的校准方法。     

Fast handoff with reducing waste rate approach for wireless resources management in UMTS mobile networks

3G Wideband CDMA systems adopt the Orthogonal Variable Spreading Factor code tree as the channelization codes management for achieving high data rate transmission in personal multimedia communications. It assigns a single channelization code for each accepted connection. Nevertheless, it wastes the system capacity when the required rate is not powers of two of the basic rate. One good solution is to assign multiple codes for each accepted connection but it causes two inevitable drawbacks: long handoff delay and new call setup delay due to high complexity of processing with multiple channelization codes, and high cost of using more number of rake combiners. Especially, long handoff delay may result in more call dropping probability and higher Grade of Service, which will degrade significantly the utilization and revenue of the 3G cellular systems. Therefore, we propose herein an adaptive efficient codes determination algorithm based on the Markov Decision Process analysis approach to reduce the waste rate and reassignments significantly while providing fast handoff. Numerical results demonstrate that the proposed approach yields several advantages, including the lowest GOS, the least waste rate, and the least number of reassignments. Meanwhile, the optimal number of rake combiners is also analyzed in this paper. This research was supported in part by the National Science Council of Taiwan, ROC, under contract NSC-93-2213-E-324-018.     

基于两层均匀媒质的GPEN SAR地下目标成像方法及其性能分析

地表穿透合成孔径雷达(Ground PENetration SAR,GPEN SAR)为了探测掩埋在地下的目标,通常工作在多层媒质的环境中。传统成像模型是建立在同一均匀媒质的假设上,不再适合于GPEN SAR的实际情况。本文首先建立了两层分区均匀媒质中的成像模型,然后利用后向投影(BP)算法定量分析了成像几何参数、土壤参数等对成像的影响,进而提出了一种修正的后向投影(MBP)算法。MBP算法不仅能够校正两层分区均匀媒质对成像定位的影响,还能估计目标的掩埋深度,提供目标三维位置坐标。仿真结果验证了MBP算法在不同信噪比环境下,对多目标的三维定位精度能满足实际的需要。     

建设新一代城域网

在传统WDMSDH基础上建设城域传输网，由于其自身的限制，造成带宽利用率较低、网络层次复杂、接口单一等问题，不能很好满足现代的通信需求，随着技术的发展，出现了OADM、MSTP等基于传统技术改进的技术和产品，本着重从这两方面介绍了建设新一代城域传输网的技术。     

A novel compact ring dual-mode filter with adjustable second-passband for dual-band applications

In this letter, a novel compact ring dual-mode with adjustable second-passband for dual-band applications are presented. A ring resonator with two different geometric dimensions are derived and designed to have identical fundamental and the first higher-order resonant frequencies, and to establish appropriate couplings in the structure. Moreover, the proposed filter has smaller size as compared with the basic topology of stopband filters and stepped-impedance-resonator (SIR) filters. The measured filter performance is in good agreement with the simulated response.     

MULTICARRIER DS—CDMA WITH ADAPTIVE MODULATION AND POWER ALLOCATION

Adaptive modulation and power allocation is introduced into the multicarrier DSCDMA system to improve the system performance and bandwidth efficiency.First,the system design appropriate for adaptive modulation and power allocation is given,then the algorithm of adaptive modulation and power allocation is applied.Simulation results demonstrate great performance improvement compared with the fixed modulated one.     

微杯电子纸及其后加工制程

SiPix利用独特的微杯(Microcup)结构和顶部灌注封装技术，通过连续整卷高速涂布的制程成功地制造出高性能的双稳性、装填电泳微粒的电子纸。SiPix可提供下列两种规格形式任意的EPD卷式成品：(A)用于有源矩阵EPD和直接驱动产品的可剥离保护膜／已灌装及密封的Microcup／无图案导体膜夹层卷；及（P）用于无源矩阵的行导体膜／已灌装及密封的Microcup／列导体膜夹层卷。已经开发出将EPD卷制成不同的显示模块或产品的简单的后续加工制程。     

An adaptive p-persistent MAC scheme for multimedia WLAN

The letter proposes an adaptive p-persistent-based (APP) medium access control (MAC) scheme for the IEEE 802.11e distributed WLAN supporting multimedia services. The APP MAC scheme adaptively gives differentiated permission probabilities to transmission stations which are in different access category and with various waiting delay. Simulation results show that the APP MAC scheme can improve the performance of multimedia WLAN, such as small voice packet dropping probability, low delay variation, and high system throughput, compared to conventional MAC algorithms     

ESD protection design to overcome internal damage on interface circuits of a CMOS IC with multiple separated power pins

This paper reports a real case of electrostatic discharge (ESD) improvement on a complementary metal oxide semiconductor integrated circuit (IC) product with multiple separated power pins. After ESD stresses, the internal damage have been found to locate at the interface circuit connecting between different circuit blocks with different power supplies. Some ESD designs have been implemented to rescue this IC product to meet the required ESD specification. By adding only an extra ESD clamp N-channel metal oxide semiconductor with a channel width of 10 /spl mu/m between the interface node and the ground line, the human-body-model (HBM) ESD level of this IC product can be improved from the original 0.5 to 3 kV. By connecting the separated vertical sync signal (VSS) power lines through the ESD conduction circuit to a common VSS ESD bus realized by the seal ring, the HBM ESD level of the enhanced version IC product with 12 separated power supplies pairs can be significantly improved from original 1 kV up to > 5 kV, without the noise coupling issue.     

Enhanced thermal stability of a sputtered titanium-nitride film as a diffusion barrier for capacitor-bottom electrodes

The effect of a thin RuO_x layer formed on the Ru/TiN/doped poly-Si/Si stack structure was compared with that on the RuO_x/TiN/doped poly-Si/Si stack structure over the post-deposition annealing temperature ranges of 450–600°C. The Ru/TiN/poly-Si/Si contact system exhibited linear behavior at forward bias with a small increase in the total resistance up to 600°C. The RuO_x/TiN/poly-Si/Si contact system exhibited nonlinear characteristics under forward bias at 450°C, which is attributed to no formation of a thin RuO_x layer at the RuO_x surface and porous-amorphous microstructure. In the former case, the addition of oxygen at the surface layer of the Ru film by pre-annealing leads to the formation of a thin RuO_x layer and chemically strong Ru-O bonds. This results from the retardation of oxygen diffusion caused by the discontinuity of diffusion paths. In particular, the RuO_x layer in a nonstoichiometric state is changed to the RuO₂-crystalline phase in a stoichiometric state after post-deposition annealing; this phase can act as an oxygen-capture layer. Therefore, it appears that the electrical properties of the Ru/TiN/poly-Si/Si contact system are better than those of the RuO_x/TiN/poly-Si/Si contact system.