Investigation of Mechanical and Electrical Characteristics for Cracked Conductive Particle in Anisotropic Conductive Adhesive (ACA) Assembly

In an anisotropic conductive adhesive (ACA) assembly, the electrical conduction is usually achieved with the conductive particles between the bumps of integrated circuit (IC) and corresponding conductive tracks on the glass substrate. Fully understanding of the mechanical and electrical characteristics of ACA particles can help to optimize the assembly process and improve the reliability of ACA interconnection. Most conductive particles used in the ACA assembly are with cracks in the metal coating of the particles after the ACA bonding. This paper introduced the fracture analysis by applying the cohesive elements in the numerical model of the nickel-coated polymer particle and further simulating the cracks initiation and propagation in the nickel coating during the ACA bonding. The simulation results showed that the stress distribution on the nickel-coated particle with cracks was significantly different from that on the nickel-coated particle without crack, indicating that the stress analysis by taking the crack into consideration is very important for the reliability assessment of the ACA interconnection. The stress analysis of cohesive elements indicated that the cracks initiated at the central area of the nickel coating and propagated to the polar area. Furthermore, by the introduction of a new parameter of the virtual resistance, a mathematical model was established to describe the electrical characteristics of the nickel-coated particle with cracks. The particle resistance of the nickel-coated particle with cracks was found to be much higher than that of the particle without crack in the optimized bonding pressure range, indicating that it is necessary to take the crack into consideration for the particle conduction analysis as well. Therefore, the fracture analysis on the conductive particle by taking the crack into consideration could accurately evaluate the reliability of ACA interconnection and avoid serious reliability issues.     

全光纤脉冲压缩器的理论及实验研究

对色散位移光纤＋普通单模光纤构成的全光纤脉冲压缩器进行了理论分析，分析了压 缩效果与光纤参数及输入脉冲参数的关系；对不同中心波长和脉宽的主动锁模光纤激光器的 输出脉冲进行了压缩实验，均得到了近变换限Sech的压缩脉冲，实验结果与理论分析一致. 关键词： 全光纤脉冲压缩器 压缩因子 基座能量 主动谐波锁模光纤 激光器     

计算机高速并行通信的实现方案

利用CPLD芯片实现单片机与ISA总线接口之间的高速并行通信，给出系统的总体设计方法及程序框图。采用这种通信方式，在12MHz晶振的MCS51单片机控制的数据采集系统中，可以满足与PCI04 ISA总线接口实时通信的要求，通信速率达200khit／s。在开发工具MAX plusⅡ下，完成了整个设计的输入、编译和仿真，达到了预期效果。本设计方案能够推广应用到计算机的高速并行通信中。     

用PM3量化参数预测多氯代二苯并呋喃的logKow

从现有的PCDFs分子的正辛醇 /水分配系数 (logKow)实验数据出发 ,建立定量结构 性质关系方程(QSPR) .采用G98W程序包中的PM3方法对 13 5个多氯代二苯并呋喃 (PCDFs)分子和二苯并呋喃进行了优化计算 ,作业命令为 #pPM3optfreqscf(conver =9) ,以计算所得的分子轨道能量、碳原子电荷作为PCDFs分子结构描述符 ,运用多元线性回归技术建立了PCDFs的logKow与分子结构描述符的四元方程 ,最优相关系数为 0 .95 0 7,标准偏差为 0 .173 7,经检验该模型的稳健性好 ,并对未有实验数据的 85个PCDFs的logKow进行预测     

Yellow‐light‐emitting cyano‐substituted poly[(1,3‐phenylene vinylene)‐alt‐(1,4‐phenylene vinylene)] derivative: Its synthesis and optical properties

A soluble cyano‐substituted poly[(1,3‐phenylene vinylene)‐alt‐(1,4‐phenylene vinylene)] derivative ( 9 ) was synthesized and characterized. Comparison between 9 and its model compound ( 10 ) showed that the chromophore in 9 remained to be well defined as a result of a π‐conjugation interruption at adjacent m‐phenylene units. The attachment of a cyano substituent only at the β position of the vinylene allowed the maximum electronic impact of the cyano group on the optical properties of the poly(p‐phenylene vinylene) material. At a low temperature (?108 or ?198 °C), the vibronic structures of 9 and 10 were partially resolved. The absorption and emission spectra of a film of 9 were less temperature‐dependent than those of a film of 10 , indicating that the former had a lower tendency to aggregate. A light‐emitting diode (LED) based on 9 emitted yellow light (λ_max ≈ 578 nm) with an external quantum efficiency of 0.03%. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3149–3158, 2003     

电致发光色纯性增强的硅基有机微腔

报道了硅基有机微腔的电致发光（EL）.该微腔由上半透明金属膜、中心有源多层膜和多孔硅分布Bragg反射镜（PS DBR）组成.半透明金属膜由Ag（２０nm）构成，充当发光器件的负电极和微腔的上反射镜.有源多层膜由Al (1 nm) / LiF(05 nm) /Alq3/Alq3:DCJTB/NPB/CuPc/ITO/SiO2组成，其中的Al/LiF为电子注入层，ITO为正电极，SiO2为使正、负电极电隔离的介质层.该PS DBR是采用设备简单、成本低廉且非常省时的电化学腐蚀法用单晶Si来制备的；该PS 关键词： 电化学腐蚀 电致发光 窄峰发射 硅基有机微腔     

CNx纳米管的制备、结构观察及低场致电子发射性能研究

采用高温热解法，以乙二胺为前驱液，在沉积有铁催化剂的p型硅（111）基底上制备出了定向生长的CNx纳米管.利用扫描电子显微镜、高分辨率透射电子显微镜和拉曼光谱对CNx纳米管进行了形貌观察和表征.CNx纳米管的高度在20?μm左右，直径在50—100nm之间，具有明显的“竹节状”结构，结晶有序度较差.对CNx纳米管薄膜进行低场致发射性能测试：外加电场为1.4V/μm，观察到20?μA /cm2发射电流，外电场升至2.54V/μm时发射电流达到1.280mA/cm2，在较高外电场下，没有发现电流“饱和”.这比 关键词： CNx纳米管 高温热解 “竹节状”结构 场致发射     

Sensitivity-enhanced IPAP experiments for measuring one-bond C–C and C–H residual dipolar couplings in proteins

Sensitivity-enhanced 2D IPAP experiments using the accordion principle for measuring one-bond 13C'-13Calpha and 1Halpha-13Calpha dipolar couplings in proteins are presented. The resolution of the resulting spectra is identical to that of the decoupled HSQC spectra and the sensitivity of the corresponding 1D acquisitions are only slightly lower than those obtained with 3D HNCO and 3D HN(COCA)HA pulse sequences due to an additional delay 2Delta. For cases of limited resolution in the 2D 15N-1HN HSQC spectrum the current pulse sequences can easily be modified into 3D versions by introducing a poorly digitized third dimension, if so desired. The experiments described here are a valuable addition to the suites available for determination of residual dipolar couplings in biological systems.     

New heuristics for over-constrained flight to gate assignments

We consider the over-constrained Airport Gate Assignment Problem where the number of flights exceed the number of gates available, and where the objectives are to minimize the number of ungated flights and the total walking distances. The problem is formulated as a binary quadratic programming problem. We design a greedy algorithm and use a Tabu Search meta-heuristic to solve the problem. The greedy algorithm minimizes ungated flights while we devise a new neighbourhood search technique, the Interval Exchange Move, which allows us flexibility in seeking good solutions, especially when flight schedules are dense in time. Experiments conducted give good results.     

辐射加热金X光再发射时间测量

利用星光Ⅱ三倍频激光打双盘靶，研究了辐射加热材料的Ｘ光发射时间。激光脉冲能量４０～６０Ｊ、脉冲宽度６００～７００ｐｓ。通过两台时间关联的亚千Ｘ光能谱仪分别监测双盘靶初、次级发射Ｘ光谱，给出了辐射加热次级Ｘ光再发射时间。