Recording of volume hologram using a beam pattern from taperedoptical fiber

A photorefractive volume hologram was recorded and probed using light diffracted from a tapered optical fiber as a reference beam. A single-mode fiber (SMF) was chemically etched and tapered to give a complicated beam pattern, and it is shown that the tapered optical fiber can be utilized to increase the storage density of the volume hologram. Spatial selectivity of the volume hologram with this method was increased by two times compared to the normal SMF referencing, which is due to the fact that the complicated beam pattern has little correlation with its shifted version     

深亚微米MOSFET衬底电流的模拟与分析

利用器件模拟手段对深亚微米ＭＯＳＦＥＴ的衬底电流进行了研究和分析，给出了有效的道长度，栅氧厚度，源漏结深，衬底掺杂浓度以及电源电压对深亚微米ＭＯＳＦＥＴ衬底电流的影响，发现电源电压对深亚微米ＭＯＳＦＥＴ的衬底电流有着强烈的影响，热载流子效应随电源电压的降低而迅速减小，当电源电压降低到一定程度时，热载流子效应不再成为影响深亚微米ＭＯＳ电路可靠性的主要问题。     

Selection of network and learning parameters for an adaptive neural robotic control scheme

This paper presents the results of a study in the design of a neural network based adaptive robotic control scheme. The neural network used here is a two hidden layer feedforward network and the learning scheme is the well-known backpropagation algorithm. The neural network essentially provides the inverse of the plant and acts in conjunction with a standard PD controller in the feedback loop. The objective of the controller is to accurately control the end position of a single link manipulator in the presence of large payload variations, variations in the link length and also variations in the damping constant. Based on results of this study, guidelines are presented in selecting the number of neurons in the hidden layers and also the parameters for the learning scheme used for training the network. Results also indicate that increasing the number of neurons in the hidden layer will improve the convergence speed of learning scheme up to a certain limit beyond which the addition of neurons will cause oscillations and instability. Guidelines for selecting the proper learning rate, momentum and fast backpropagation constant that ensure stability and convergence are presented. Also, a relationship between the r.m.s. error and the number of iterations used in training the neural network is established.     

A new hybrid active power filter (APF) topology

In this paper, a new hybrid active power filter topology is presented. A higher-voltage, low-switching frequency insulated gate bipolar transistor (IGBT) inverter and a lower-voltage high-switching frequency metal oxide semiconductor field effect transistor (MOSFET) inverter are used in combination to achieve harmonic current compensation. The function of the IGBT inverter is to support utility fundamental voltage and to compensate for the fundamental reactive power. The MOSFET inverter fulfills the function of harmonic current compensation. To further reduce cost and to simplify control, the IGBT and MOSFET inverters share the same DC-link via a split capacitor bank. With this approach harmonics can be cancelled over a wide frequency range. Compared to the conventional APF topology, the proposed approach employs lower dc-link voltage and generates less noise. Simulation and experimental results show that the proposed active power filter topology is capable of compensating for the load harmonics     

Characterization method of thermomechanical parameters for microelectronic materials

Reliability of thermomechanical simulations is critically linked to the accuracy of the mechanical properties that govern the behaviour of structure, like Young's modulus (E) and coefficient of thermal expansion (CTE). For many cases, the values found in literatures are dealing with bulk properties without detailed information on temperature effects. To address such issues, it is necessary to measure the materials parameters as a function of temperature. The measurement of CTE is usually accomplished by evaluating the thermal deflections of a subjected material layer deposited on a substrate, providing that E is known at a specific temperature of experiment. A bilayer method, based on theory of elasticity, is proposed to determine both E and CTE for a given temperature with a good resolution. This paper presents the theoretical analysis, the design and process of the microsystem test structures, and the main calculation results.     

Linewidth and FM characteristics of a distributed feedback laser monolithically integrated with a tunable external cavity

A narrow linewidth has been obtained in a new 1.5 ?m distributed feedback laser integrated monolithically with a tunable external cavity. The linewidth of 18 MHz has been achieved by tuning the current in the external cavity, and the FM response was flat from 100 kHz to 500 MHz.     

On a stochastic nonlinear equation in one-dimensional viscoelasticity

In this paper we discuss an initial-boundary value problem for a stochastic nonlinear equation arising in one-dimensional viscoelasticity. We propose to use a new direct method to obtain a solution. This method is expected to be applicable to a broad class of nonlinear stochastic partial differential equations.

     

Scanning tunnelling microscope studies of growth of RuO2（110） thin layer on Ru（0001）

This paper reports that the growth of RuO_x(110) thin layer growth on Ru(0001) has been investigated by means of scanning tunnelling microscope (STM). The STM images showed a domain structure with three rotational domains of RuO_x(110) rotated by an angle of 120℃. The as-grown RuO_x(110) thin layer is expanded from the bulk-truncated RuO_x(110) due to the large mismatch between RuO_x(110) and the Ru(0001) substrate. The results also indicate that growth of RuO_x(110) thin layer on the Ru(0001) substrate by oxidation tends first to formation of the Ru-O (oxygen) chains in the [001] direction of RuO_x(110).     

Performance engineering and topological design of metro WDM opticalnetworks using computer simulation

This paper demonstrates the use of computer simulation for topological design and performance engineering of transparent wavelength-division multiplexing metropolitan-area networks. Engineering of these networks involves the study of various transport-layer impairments such as amplifier noise, component ripple, chirp/dispersion, optical crosstalk, waveform distortion due to filter concatenation, fiber nonlinearities, and polarization effects. A computer simulation methodology composed of three main simulation steps is derived and implemented. This methodology obtains performance estimations by applying efficient wavelength-domain simulations on the entire network topology, followed by time-/frequency-domain simulations on selected paths of the network and finally Q-budgeting on an identified worst case path. The above technique provides an efficient tool for topological design and network performance engineering. Accurate simulation models are presented for each of the performance impairments, and the computer simulation methodology is used for the design and engineering of a number of actual metro network architectures     

Applications of coupled LC-GC: A review

Although coupled liquid chromatographygas chromatography (LC-GC) was first demonstrated ten years ago, only in the last few years has there been a sudden surge of interest in the technique. Approximately 70% of the total number of LC-GC applications have been published in the last two years (1987–88) alone. This review categorizes LC-GC publications into four main application areas: fossil fuels, foods, environmental samples, biologiical/pharmaceutical samples, and miscellaneous samples. Multidimensional separations carried out using other coupled-column chromatographic techniques (such as supercritical fluid chromatography (SFC) with GC, and on-line trace enrichment-GC) have also been included in this review.