Determination of the glass transition temperature of latex films: Comparison of various methods

The glass transition temperature (T_g) for two latices with different styrene/butadiene compositions was determined by the thermal SPM probe resonance frequency method. The results were compared with the T_g values obtained by differential scanning calorimetry (DSC), dynamical mechanical analysis (DMA), process rheometer (PR) and thermo-mechanical analyzer (TMA) measurements. The T_g values detected by the thermal SPM method agreed well with the T_g values obtained by DSC and calculated by the Fox–Flory equation. DMA, on the other hand, showed a significantly higher T_g value for both latices than those obtained from theoretical calculations, the thermal SPM method and DSC. The T_g obtained from the PR curve was slightly higher for the latex with a low styrene content, whereas good agreement was obtained with the thermal SPM data for the latex with a high styrene content. The glass transition temperature determined by TMA agreed fairly well with the thermal SPM data for the latex with the low styrene content, whilst the value of T_g for the second latex was much less than those obtained by the other methods. The thermal SPM method detects changes in thermal behavior (thermal diffusivity, heat capacity) during heating of the latex films rather than changes in the mechanical properties. Information about the sample history could be seen in the thermal SPM curves, which was further associated with the degree of latex film formation, especially when the roughness of the films was taken into consideration.     

Effect of temperature on the buildup of polyelectrolyte multilayers

The effect of temperature on the buildup of polyelectrolyte multilayers consisting of poly(styrenesulfonate) (PSS), poly(diallyldimethylammonium) (PDADMA), and poly(allylamine) (PAH) was studied by using a quartz crystal microbalance. The increase of temperature in the deposition process was shown to have a considerable effect on the rate of the layer-by-layer buildup. The effect of temperature on the PDADMA/PSS deposition was found to be stronger than on the PAH/PSS deposition. The increasing temperature was found to extend the exponential buildup regime in all of the studied systems. A buildup model was created to simulate the buildup and to explain the effect of temperature. The model is based on the assumption that each deposition step leads to a quasi-equilibrium between the concentration of the polymer repeating unit in solution and the composition of the layer. According to the model, the layer-by-layer buildup is inherently exponential, becoming linear whenever diffusion is not fast enough to carry the polymer within the entire thickness of the film. This buildup model is discussed jointly with the earlier published three-zone model of the polyelectrolyte multilayers. The rate of the buildup is characterized by growth exponent beta. The temperature dependence of the growth exponent is discussed in connection with the thermodynamic parameters of the deposition.     

Thermal and topographical characterization of polyester- and styrene/acrylate-based composite powders by scanning probe microscopy

The thermal properties of two conventional polyester-based toners and a chemically prepared styrene/acrylate toner with different thermal histories were studied by scanning probe microscopy (SPM) and differential scanning calorimetry (DSC). The thermal transition temperatures detected by SPM agreed with the results of the DSC measurements. The validity of SPM for detecting thermal transitions was further confirmed by studying two amorphous reference polymers with different glass transition points (T_g) and three crystalline reference polymers with different melting points (T_m). When the toner sample was heated by the SPM probe above the glass transition temperature of the toner powder (T_probe > T_g), changes occurred in the surface topography and roughness causing different levels of local sintering of the particles. A set of roughness parameters calculated from the SPM image data were used to quantify the most essential features of toner surfaces. Environmental scanning electron microscopy (ESEM) was used to study the penetration depth of heat dissipated by the SPM probe. The probe-annealing was compared with oven-annealing in order to establish the effect of thermal history on the thermal properties of the materials.     

An efficient strategy for the synthesis of 1-chloroethyl phosphates and phosphoramidates

[reaction: see text] A versatile, efficient, and simple method for the preparation of various 1-chloroethyl phosphates and phosphoramidates is described. The protected chlorophosphates or phosphoramidates are synthesized to the vinyl derivative under mild conditions, followed by conversion to the chloroethylidene phosphate or phosphoramidate by dry HCl gas, resulting in good to excellent yields. 1-Chloroethyl phosphates and phosphoramidates are excellent building blocks for the synthesis of novel ethylidene-linked phosphate prodrugs.     

Morphological changes in never-dried kraft fibers under mechanical shearing

The modification of bleached never-dried cellulose fibers was studied under controlled compression and shearing conditions. Fibers were further treated in a high-intensity mixing device in low-consistency to determine if the fiber structure was weakened in the in-pad attrition. The difference between the development of the softwood and hardwood fibers was examined. The fiber properties were analyzed using a fiber morphology analyzer, fractional fiber analysis and an electron microscope. The results indicate that the shearing under the controlled compression at high consistency modified the softwood and hardwood fibers already at low-energy consumptions. The fiber length and width decreased, and the formation of curls and kinks was pronounced. However, the intensive mixing after in-pad attrition revealed that the fiber structure was not weakened under compression and shear forces; conversely, the fiber cell wall was more resistant for the intensive mixing. When comparing the results for hardwood and softwood fibers, the softwood fibers were more modified during in-pad attrition, whereas the fiber wall strengthening was more significant in the hardwood fibers.     

Liquid chromatography tandem mass spectrometry determination of total budesonide levels in dog plasma after inhalation exposure

A sensitive and selective method to quantify budesonide in dog plasma samples was developed and fully validated. Liquid–liquid extraction was followed by solid-phase extraction and liquid chromatography–tandem mass spectrometry with electrospray ionization. After reconstitution of the analytes in the mobile phase, samples were analysed by reversed-phase liquid chromatography with isocratic elution. d8-Budesonide was used as an internal standard, and characteristic transitions of d8-budesonide and budesonide were used for quantification. The method was validated with respect to selectivity, specificity, linearity, recovery, repeatability, reproducibility and limits of detection and quantification. The validated method was successfully applied to monitor the plasma levels of budesonide in dogs exposed to clinical doses of inhaled and intravenous drug.     

Experimental humidity dependency of small particle adhesion on silica and titania

The humidity present in ambient atmosphere affects the adhesion of small particles by causing capillary bridge formation between the particle and the surface. Even in moderate relative humidities this, usually attractive, force can have a significant effect on adhesion behaviour of micro and sub-micro particles. We have directly measured the pull-off forces of initially adhered oxide particles on oxide surfaces with atomic force microscope in controlled atmosphere with adjustable humidity. We demonstrate the effect of the surface roughness resulting in two different regions of capillary formation and the particle shape having a strong effect on the humidity dependency of adhesion. The experimental results are explained by theoretical framework.     

Twisted K Theory Invariants

An invariant for twisted K theory classes on a 3-manifold is introduced. The invariant is then applied to the twisted equivariant classes arising from the supersymmetric Wess–Zumino–Witten model based on the group SU(2). It is shown that the classes defined by different highest weight representations of the loop group LSU(2) are inequivalent. The results are compatible with Freed–Hopkins–Teleman identification of twisted equivariant K theory as the Verlinde algebra.     

Cationic wood cellulose films with high strength and bacterial anti-adhesive properties

In this work, periodate oxidized birch wood pulp and microfibrillated cellulose (MFC) were cationized using Girard’s reagent T or aminoguanidine. Cationic celluloses were used to obtain films via solvent-casting method, and the effects of the cationization route and the cellulose fiber source on the properties of the films were studied. Thermal and optical properties of the films were measured using differential scanning calorimetry and UV–Vis spectrometry, and the morphology of the films was examined using an optical microscope and a field emission scanning electron microscope. Bacterial anti-adhesive properties of the films were also studied using a modified leaf print method and against Staphylococcus aureus and Escherichia coli. Both cationizing agents exhibited similar reactivity with periodate oxidized celluloses, however, MFC had significantly higher reactivity compared to birch pulp. The films with high tensile strength (39.1–45.3 MPa) and modulus (3.5–7.3 GPa) were obtained from cationized birch pulp, aminoguanidine modification producing a film with slightly better mechanical properties. Modulus of the films was significantly increased (up to 14.0 GPa) when MFC was used as a cellulose fiber source. Compared to the unmodified MFC films, the cationic MFC films were less porous and significantly more transparent; however, they had slightly lower tensile strength values. It was found that aminoguanidine modified celluloses had no culturable bacteria on its surface and also exhibited resistance to microbial degradation, whereas there were culturable bacteria on the surface of Girard’s reagent modified films and they were partially degraded by the bacteria.     

Effect of tempo and periodate-chlorite oxidized nanofibrils on ground calcium carbonate flocculation and retention in sheet forming and on the physical properties of sheets

Nanofibrils (NFC) or microfibrils (MFC) are potential candidates for high filler-loaded papers and board as they are able to compensate for strength loss caused by the filler itself. However, the interaction of nanofibrils and the filler during sheet forming is not yet well understood. The aim here was to examine 2,2,6,6-tetramethylpiperidine-1-oxyl radical (TEMPO) and periodate-chlorite oxidized (DCC) anionic nanofibrils during sheet forming in order to determine their effects on flocculation, filler retention and the strength and optical properties of the handsheets. The experiments were carried out by manufacturing filler-loaded sheets from refined kraft fibres and ground calcium carbonate (GCC) with various added levels of TEMPO and DCC nanofibrils. The results showed that both types of nanofibril caused pronounced agglomeration of the GCC filler, which increased its retention in the paper web. Given the same filler content, the strength properties were the same or slightly better than in a sheet formed without any chemical agent, while light scattering was slightly inferior. Poorer formation seemed to be the explanation for why the increased bonding induced by NFCs was not reflected in obviously better sheet strengths. The physical properties of sheets containing NFC were superior to those of sheets formed with cationic polyacrylamide as a retention aid with the same filler content and level of formation. Thus NFCs seem to be potential retention aids for use in fine paper production instead of traditional polymers.