Comparison of four quantification methods for the determination of PCB in transformer oils

The analysis of PCB in transformer oils has been achieved with three HRGC/ECD based methods, proposed by the International Electrotechnical Commission (IEC/TC 10), by the Comité Européen de Normalisation (CEN/TC 19/WG 22) and by the Deutsches Institut für Normung (DIN 51 527). The same clean-up, described in the CEN/TC 19/WG 22, has been used for all the samples, allowing a comparison of the quantification procedure only. The total chlorine content has also been determined with X-ray fluorescence. These different methods of quantification are compared and their application for legislative purposes is discussed.Dedicated to Professor Dr Dieter Klockow on the occasion of his 60th birthday     

Preconcentration of trace antimony in tap and sea water on activated alumina. Determination by graphite furnace atomic absorption spectrometry

Summary A method is described for antimony preconcentration based on retention on a column of activated alumina. Recovery is 80% when no pH-control and 4 mol/l HCl as eluent are used. The preconcentration factor is 400. The method was applied to the determination of antimony in spiked tap and sea water. The analytical performance of the method is discussed.     

A boost-type converter for DC-supply of fluorescent lamps

A boost type converter is described that is suitable for low-voltage DC-supply of fluorescent lamps. It has inherent lamp current limitation (ballast action) and provides the high voltage pulses and electrode heating that are required for igniting the lamp. The proposed circuit is applicable in automotive, emergency, and portable light sources.<>     

On the piezoelectricity of anionic collagen films

In this paper, we report results of a study of the physicochemical, dielectric and piezoelectric properties of anionic and native collagen films, considering the development of new biomaterials which have potential applications in coating of cardiovascular prostheses, support for cellular growth and in systems for controlled drug delivery. The piezoelectric strain tensor element d₁₄, the elastic constant s₅₅, and the dielectric permittivity ?₁₁ were measured for the anionic and native collagen films. It was observed that the collagen samples submitted to the alkaline treatment present lower thermal stability than those made from native collagen. However, the treated samples present a higher piezoelectricity compared with the native collagen. The frequency constant fL and the piezoelectric strain element d₁₄, obtained for the alkaline-treated sample (72 h), present the highest values for the samples under study (444.1 kHz m and 0.079 pC/N, respectively). We believe that the alkaline treatment led to an increase of the organization of the microscopic fiber structure of the sample, which could result in an increase of the piezoelectricity.     

Influence of Al content x on hot electron noise in AlxGa1-xAs n+nn+ devices: comparison withGaAs

Hot electron noise measurements are performed in Si doped Al_x Ga_1-xAs n⁺nn⁺ devices, for three different Al concentrations: x=0.15, 0.2, 0.25. Noise temperatures are obtained using a pulsed measurement technique as functions of electric field and frequency. Longitudinal diffusion coefficients D(E) are deduced at 4 GHz. Results are analyzed through the scattering mechanisms which greatly affect the electron velocity properties of Al_xGa_1-xAs materials. Comparisons with n⁺ nn⁺ GaAs devices are made     

On the hot-carrier-induced post-stress interface trap generation inn-channel MOS transistors

A continued fast interface trap generation is observed in n-channel MOS transistors after termination of the hot-carrier stress. The magnitude of this post-stress effect is strongly dependent on the conditions of the preceding stress, on the post-stress conditions and on the process parameters. For measurements at 293 K, a simple model is proposed which is based on the release of hydrogen by the thermal detrapping of holes, and which can explain the observed dependencies. The importance of the post-stress D_it-generation is illustrated for the case of dynamic stress conditions where it can lead to an apparently deviating degradation behavior