高质量的一级光栅1．55μmDFB激光器

本文详细叙述了ＤＦＢ激光器的设计要点和新的工艺。采用一级全息光栅和二步液相外延法批量研制出高稳定单纵模工作的１．５５μｍ分布反馈激光器（ＤＦＢ—ＬＤ）。外延片成品率＞４０％。器件特性：２５℃时阈值电流２０ｍＡ，单面光功率＞１０ｍｗ，主边模抑制比ＳＭＳＲ达４３ｄＢ（λ／４相移光栅），谱线宽度△ν－２０ｄＢ＝０．３ｎｍ，调制速率＞１．８ＧＨｚ。可靠性测试显示：高温监测光谱稳定，２５°Ｃ时阈值退化率△Ｉｔｈ／ｔ＜０．３ｍＡ／ｋｈ，对应器件预估寿命将超过１０万ｈ。     

Modeling low-frequency electrode-type resistivity tools in invadedthin beds

The authors formulate and implement a numerical mode-matching (NMM) method to model electrode-type resistivity tools in invaded thin beds. The authors derive the low-frequency approximation of the Maxwell's equations to obtain the partial differential equation for the potential field. The new NMM program is validated by comparing the numerical results with those obtained from other dc programs. It is found that this new program is much faster than the program using the finite-element method (FEM), and hence is useful for routine interpretation of resistivity logs and for inversion     

An error and sensitivity analysis of the atmospheric- andsoil-correcting variants of the NDVI for the MODIS-EOS

Several soil- and atmospheric-correcting variants of the normalized difference vegetation index (NDVI) have been proposed to improve the accuracy in estimating biophysical plant parameters. In this study, a sensitivity analysis, utilizing simulated model data, was conducted on the NDVI and variants by analyzing the atmospheric- and soil-perturbed responses as a continuous function of leaf area index. Percent relative error and vegetation equivalent “noise” (VEN) were calculated for soil and atmospheric influences, separately and combined. The NDVI variants included the soil-adjusted vegetation index (SAVI), the atmospherically resistant vegetation index (ARVI), the soil-adjusted and atmospherically resistant vegetation index (SARVI), the modified SAVI (MSAVI), and modified SARVI (MSARVI). Soil and atmospheric error were of similar magnitudes, but varied with the vegetation index. All new variants outperformed the NDVI. The atmospherically resistant versions minimized atmospheric noise, but enhanced soil noise, while the soil adjusted variants minimized soil noise, but remained sensitive to the atmosphere. The SARVI, which had both a soil and atmosphere calibration term, performed the best with a relative error of 10 percent and VEN of ±0.33 LAI. By contrast, the NDM had a relative error of 20 percent and VEN of ±0.97 LAI     

Suppression of boron penetration in p+ polysilicon gateP-MOSFETs using low-temperature gate-oxide N2O anneal

It has been reported that high-temperature (~1100°C) N₂ O-annealed oxide can block boron penetration from poly-Si gates to the silicon substrate. However, this high-temperature step may be inappropriate for the low thermal budgets required of deep-submicron ULSI MOSFETs. Low-temperature (900~950°C) N₂O-annealed gate oxide is also a good barrier to boron penetration. For the first time, the change in channel doping profile due to compensation of arsenic and boron ionized impurities was resolved using MOS C-V measurement techniques. It was found that the higher the nitrogen concentration incorporated at Si/SiO₂ interface, the more effective is the suppression of boron penetration. The experimental results also suggest that, for 60~110 Å gate oxides, a certain amount of nitrogen (~2.2%) incorporated near the Si/SiO₂ interface is essential to effectively prevent boron diffusing into the underlying silicon substrate     

Development of Bi(Pb)-2223/Ag pancake-shaped and solenoidal coils

High temperature superconducting (HTSC) multifilamentary (MT) Bi(Pb)-2223/Ag tapes with reproducible critical current density of between 15000 and 20000 A/cm² at 77 K in self field have been achieved using the standard flat-rolling method as the intermediate deformation between sintering periods. Long lengths of Bi(Pb)-2223/Ag MT tapes up to 43 m prepared by the conventional method of powder-in-tube (PIT) have been successfully produced on a laboratory scale. Several coils have been fabricated from sections of the long length tape, using the co-wound wind-and-react (W&R) procedure for the pancake-shaped and the singly-wound W&R as well as R&W procedure for the solenoidal coils. A novel W&R solenoidal coil (reaching ~973 ampere-turns) wound on an alumina ceramic tube generates a DC field of ~19 mT at 77 K and has been fabricated together with five pancake-shaped coils, each generating an average of ~5 mT at 77 K. These are destined for magnet construction with a possible combined calculated field of ~0.04 T at 77 K (with liquid nitrogen as a coolant)     

Solution of nonlinear kinematics of a parallel-link constrained Stewart platform manipulator

The Stewart platform manipulator is a fully parallel kinematic linkage system that has great advantages over typical serial link robots. However, one major problem in controlling this kind of manipulator is that, due to its closed kinematic chain and parallel-link constrained structure, it is impossible to derive an explicit kinematic solution. This paper proposes a simplified algorithm to numerically solve the forward kinematics of a six-links Stewart platform. Taking advantage of some fundamental geometric operations, the proposed algorithm involves only 3 nonlinear simultaneous equations. The explicit expressions are derived for some special configurations which can directly give the geometric limitations to motion in terms of the geometric dimensions of the platforms and the legs.Research was supported by Texas Advanced Technology program under grant 003656-008 and National Science Foundation under grant MSS9211970.     

羰基铁类随机混合吸波材料等效电磁参数的计算

本文为计及多重散射偶极子间的相互作用，引入参量εｈ和μｈ，导得一组公式。它不仅能计算铁氧体类也能计算羰基铁类的随机混合吸波材料的等效电磁参数，均与实验结果吻合良好。     

A constrained joint source/channel coder design

The design of joint source/channel coders in situations where there is residual redundancy at the output of the source coder is examined. It has previously been shown that this residual redundancy can be used to provide error protection without a channel coder. In this paper, this approach is extended to conventional source coder/convolutional coder combinations. A family of nonbinary encoders is developed which more efficiently use the residual redundancy in the source coder output. It is shown through simulation results that the proposed systems outperform conventional source-channel coder pairs with gains of greater than 9 dB in the reconstruction SNR at high probability of error     

Reversible addition–fragmentation transfer (RAFT) copolymerization of methyl methacrylate and styrene in miniemulsion

In the reversible addition–fragmentation transfer (RAFT) copolymerization of two monomers, even with the simple terminal model, there are two kinds of macroradical and two kinds of polymeric RAFT agent with different R groups. Because the structure of the R group could exert a significant influence on the RAFT process, RAFT copolymerization may behave differently from RAFT homopolymerization. The RAFT copolymerization of methyl methacrylate (MMA) and styrene (St) in miniemulsion was investigated. The performance of the RAFT copolymerization of MMA/St in miniemulsion was found to be dependent on the feed monomer compositions. When St is dominant in the feed monomer composition, RAFT copolymerization is well controlled in the whole range of monomer conversion. However, when MMA is dominant, RAFT copolymerization may be, in some cases, out of control in the late stage of copolymerization, and characterized by a fast increase in the polydispersity index (PDI). The RAFT process was found to have little influence on composition evolution during copolymerization. The synthesis of the well‐defined gradient copolymers and poly[St‐b‐(St‐co‐MMA)] block copolymer by RAFT miniemulsion copolymerization was also demonstrated. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 6248–6258, 2004     

Application of asymptotic waveform evaluation to eigenmode expansion method for analysis of simultaneous switching noise in printed circuit boards (PCBs)

In this paper, the asymptotic waveform evaluation (AWE) technique is first applied to the conventional eigenmode expansion method for characterizing a power/ground (P/G) plane pair and analyzing the simultaneous switching noise on such plane pairs for printed circuit boards or multichip modules. The application of AWE avoids a large number of iterations in computing the impedance frequency response of a P/G plane pair structure and greatly reduces the computation time. Meanwhile, to obtain an accurate solution in an entire frequency range, we employ the complex frequency hopping technique which can help select multiple expansion points. In addition, the proposed approach can also be used to characterize the P/G plane pair structures with irregular shapes. Three examples demonstrate its high efficiency and good accuracy.