A 0.9 V 92 dB Double-Sampled Switched-RC Delta-Sigma Audio ADC

A 0.9 V third-order double-sampled delta-sigma audio ADC is presented. A new method using a combination of a switched-RC technique and a floating switched-capacitor double-sampling configuration enabled low-voltage operation without clock boosting or bootstrapping. A three-level quantizer with simple dynamic element matching was used to improve linearity. The prototype IC implemented in a 0.13 CMOS process achieves 92 dB DR, 91 dB SNR and 89 dB SNDR in a 24 kHz audio signal bandwidth, while consuming 1.5 mW from a 0.9 V supply. The prototype operates from 0.65 V to 1.5 V supply with minimal performance degradation.     

Efficient microwave induced direct α-halogenation of carbonyl compounds

A novel and direct method for the synthesis of α-halocarbonyl compounds using sequential treatment of carbonyl compounds with [hydroxy(tosyloxy)iodo]benzene followed by magnesium halides under solvent-free microwave irradiation conditions is described.     

Algebraic decoding of (103, 52, 19) and (113, 57, 15) quadratic residue codes

In this paper, two algebraic decoders for the (103, 52, 19) and (113, 57, 15) quadratic residue codes, which have lengths greater than 100, are presented. The results have been verified by software simulation that programs in C++ language have been executed to check possible error patterns of both quadratic residue codes.     

Reliability and wireability optimizations for chip placement on multichip modules

The chip placement problem of multichip module (MCM) designs is to map the chips properly to the chip sites on the MCM substrate. Chip placement affects not only the thermal characteristics of an MCM but also routing efficiency, which translates directly into manufacturability, performance, and cost. This paper presents a solution methodology for the optimal placement problem considering both thermal and routing design objectives simultaneously. The coupling is achieved through use of a hybrid-force model that is a combination of the traditional interconnection-force model and a novel thermal-force model. The placement procedure can be used as a design tool to place chips and then determine the tradeoffs which can be made in placing for reliability and wireability. Experiments on five examples including three benchmarks show that the present algorithm yields very high-quality results.     

Direct adaptive control of nonminimum phase systems using integralaction

A direct adaptive control scheme is proposed for nonminimum-phase systems in which controller parameters are estimated from the recursive least-squares algorithm and additional auxiliary parameters are obtained from the proposed polynomial identity. A local convergence is guaranteed without any extra condition. Integral action is incorporated into the adaptive controller to eliminate the steady-state error and to satisfy a condition of the unique solution for the polynomial identity. The control law used in this scheme is based on the set-point-on-I-only proportional-integral-derivative (PID) structure     

High dielectric constant thin film EBG power/ground network for broad-band suppression of SSN and radiated emissions

We experimentally demonstrated the great advantages of a high dielectric constant thin film electromagnetic bandgap (EBG) power distribution network (PDN) for the suppression of power/ground noises and radiated emissions in high-performance multilayer digital printed circuit boards (PCBs). Five-layer test PCBs were fabricated and their scattering parameters measured. The power plane noise and radiated emissions were measured, investigated and related to the PDN impedance. This successfully demonstrated that the bandgap of the EBG was extended more than three times, covering a range of hundreds of MHz using a 1-cm /spl times/ 1-cm EBG cell, the SSN was reduced from 170 mV to 10 mV and the radiated emission was suppressed by 22 dB because of the high dielectric constant thin film EBG power/ground network.     

Entities,identities, identifiers and credentials — what does it all mean?

This paper looks at the concepts of entities, identities, identifiers and credentials, their definitions, and how they combine to authenticate an identity to an account, or function, within a service. Credentials can be divided into several different types on the basis of their use, origin and characteristics. In particular, types such as composite, dynamic and derived credentials will be considered, and their applicability within an identity management system. Each credential must be managed through its entire life cycle from initial registration, general use and suspension, to deletion. The notion of public (i.e. freely distributable) and private (i.e. known only to you) aspects of a credential is explored. The bindings, by trusted third parties, of identifiers and public credentials into permits and instruments of proof is explained along with the convenience, but greater exposure, of local information. Several scenarios are analysed in terms of how different types of credentials are employed during the authentication process.     

Dielectric reliability of stacked Al2O3–HfO2 MIS capacitors with cylinder type for improving DRAM data retention characteristics

Dielectric reliability in Al₂O₃(2–3.1nm)–HfO₂(3nm) stack capacitor with Metal–Insulator–Si(MIS) structure is investigated in this paper. We propose an optimized capacitor process through the Time–Dependent Dielectric Breakdown (TDDB) data under various process conditions. Furthermore, due to asymmetric current at both negative and positive voltage stress polarities, we show different lifetime extrapolation by a fluence–driven model. As a result, the maximum allowed operating voltage is projected to be 1.7V (failure rate 10ppm during 10year @ 85°C) for Data “0” retention lifetime.     

Spectrum efficient region-based resource allocation with fractional loading for FH-OFDMA cellular systems

A practical resource management method that can significantly reduce cochannel interference (CCI) and improve spectrum utilisation in FH-OFDMA packet-based cellular networks is presented. The proposed method seeks an effective combination of dynamic resource allocation with fractional coding and bit loading to respectively minimise CCI and maximise system throughput for a desired performance.     

W-band divide-by-3 frequency divider using 0.1 /spl mu/m InAlAs/InGaAs metamorphic HEMT technology

A W-band divide-by-3 frequency divider with wide bandwidth and low power dissipation is presented using harmonic injection-locking technique. A cascode FET is employed for a self-oscillating second-harmonic mixer which is injection-locked by third-harmonic input to obtain the division order of three. The fabricated frequency divider using 0.1 /spl mu/m GaAs metamorphic HEMT technology shows superior performance such as large bandwidth of 6.1 GHz around 83.1 GHz (7.3%) under small DC power consumption of 12 mW.