水雾化制备Fe74Al4Sn2P10C2B4Si4非晶合金粉末及其磁粉芯性能研究

采用水雾化方法制备Fe7Al4Sn2P10C2B4Si4合金粉末,研究发现该合金具有强的非晶形成能力和高热稳定性,在粉末粒度小于400目时可以形成非晶态合金.采用该非晶粉末制备的磁粉芯在高频下品质因数显著高于MPP粉芯,说明该磁粉芯高频损耗较低.分析表明,非晶合金磁粉芯高频下损耗低的主要原因是电阻率较高.     

多功能半导体激光医疗仪电源的研制

根据“多功能半导体激光医疗仪”整机的要求,采用同一电源对667nm和808nm半导体激光器实施供电。为避免电源在开、关机时对半导体激光管产生浪涌冲击,电源在设计中采用了适当的逻辑功能。并可保证对667nm激光器供电时,即使打开808nm激光器供电开关,也不对808nm半导体激光器供电,反之亦然。电源设有手动、计算机两种控制方法,及恒定功率、电流两种工作方式。     

无线信道中的电波传播

分析了信号在无线信道中传输时所经受的两种衰落,介绍了主要的无线传播模型,在此基础上提出了对抗衰落的措施。     

Surface free energy of CrNx films deposited using closed field unbalanced magnetron sputtering

CrN_x thin films have attracted much attention for semiconductor IC packaging molding dies and forming tools due to their excellent hardness, thermal stability and non-sticking properties (low surface free energy). However, few data has been published on the surface free energy (SFE) of CrN_x films at temperatures in the range 20-170 °C. In this study CrN_x thin films with CrN, Cr(N), Cr₂N (and mixture of these phases) were prepared using closed field unbalanced magnetron sputtering at a wide range of Cr⁺² emission intensity. The contact angles of water, di-iodomethane and ethylene glycol on the coated surfaces were measured at temperatures in the range 20-170 °C using a Dataphysics OCA-20 contact angle analyzer. The surface free energy of the CrN_x films and their components (e.g., dispersion, polar) were calculated using the Owens-Wendt geometric mean approach. The influences of CrN_x film surface roughness and microstructure on the surface free energy were investigated by atomic force microscopy (AFM) and X-ray diffraction (XRD), respectively. The experimental results showed that the lowest total SFE was obtained corresponding to CrN at temperature in 20 °C. This is lower than that of Cr(N), Cr₂N (and mixture of these phases). The total SFE, dispersive SFE and polar SFE of CrN_x films decreased with increasing surface temperature. The film roughness has an obvious effect on the SFE and there is tendency for the SFE to increase with increasing film surface roughness.     

一机多控视频点播系统

介绍一种自行设计、开发的一机多控视频点播系统，讲述了系统组成及设计方案，它具有服务功能多，操作方便、性能价格比高等特点。     

偶氮苯衍生物三阶非线性的四波混频研究

用皮秒Ｎｄ：ＹＡＧ激光器的倍频光（５３２ｎｍ）对具有离域π－共轭电子云结构的偶氮苯类样品材料作简并四波混频补给，测得三阶非线性电极化率ｘ＾（３）和它们的时间响应分别为１０＾－９ｅｓｕ和２０ｐｓ，并对影响ｘ＾（３）的瞬时光栅作用和ｘ＾（３）的响应时间人了讨论。     

Influence of Cr interlayer on the structure and optical properties of Ag films on glass substrate by magnetron sputtering

Optical properties and microstructure of Ag film on glass substrate with Cr intermediate layer were studied by using spectrophotometer and XRD. The spectra results showed that introducing Cr intermediate layer reduced the surface roughness and promoted the reflectivity of Ag film. The XRD analysis showed that the crystalline grains increased and the stress decreased. The adhesion was also improved by using the tape test method.     

Preparing polymer brushes on polytetrafluoroethylene films by free radical polymerization

Films of polytetrafluoroethylene (PTFE) were exposed to sodium naphthalenide (Na/naphtha) etchant so as to defluorinate the surface for obtaining hydroxyl functionality. Surface-initiators were immobilized on the PTFE films by esterification of 4,4′-azobis(4-cyanopentanoic acid) (ACP) and the hydroxyl groups covalently linked to the surface. Grafting of polymer brushes on the PTFE films was carried out by the surface-initiated free radical polymerization. Homopolymers brushes of methyl methacrylate (MMA) were prepared by free radical polymerization from the azo-functionalized PTFE surface. The chemical composition and topography of the graft-functionalized PTFE surfaces were characterized by X-ray photoelectron spectroscopy (XPS), attenuated total reflectance (ATR) FT-IR spectroscopy and atomic force microscopy (AFM). Water contact angles on PTFE films were reduced by surface grafting of MMA.     

石家庄市CATV系统网络技术指标分配初探

在ＣＡＴＶ系统网络工程设计中，技术指标的分配产关键问题。本文介绍了石家庄市在系统设计时采用的符合实际的设计程序，并对系统前端，传输及用户网各部分技术指标的确定，计算与分配方法，指标的核算等作了较详细地阐述，以供同行参考。