Preparation and structural stability investigation of CoN/CN soft X-ray multilayers

The structural stability of heat-treated CoN/CN soft X-ray multilayers fabricated by dual-facing-target sputtering has been investigated by using complementary measurement techniques. The high temperature annealing results imply that the destructive threshold of the Co/C multilayers is improved by 100–200 degrees centigrade through doping with N. The low-angle X-ray diffraction of CoN/CN soft X-ray multilayers indicates that the period expansion of the multilayers is only 4 % at 400°C, and the interface pattern still exists even if they were annealed at 700°C. The Raman spectra analyses give the evidence that the formation of the sp³ bonding in the CN sublayers can be suppressed effectively by doping N with atoms, and thus the period expansion resulting from the changes in the density of CN layers can be decreased considerably. The X-ray photoelectron spectra analyses present the information of the existence of the strong covalent bonding betweenC andN atoms, and the ionic bonding between Co and N atoms, which can slow down the tendency of the structural relaxation. The interstitial N atoms decrease the mobility of Co atoms, and thus the fcc-Co and hcp-Co coexist even though the annealing temperature is much higher than the phase transformation temperature of 420°C, leading to the suppression of the grain growth.     

四氢β—咔啉类化合物的~(13)C NMR研究

测定了四对新合成的四氢β-咔啉化合物的~13C NMR谱,通过APT,HETCOR和HETCOLOC谱指认了所有碳的归属.所确定的化学位移规律可以用来确定它们的构型.     

Accurate mass measurements of organic compounds by an internal standard method for laser desorption/electron impact fourier transform mass spectrometry

A method for determining accurate relative molecular masses and elemental compositions of several non-volatile and thermally labile organic compounds in the source cell was established. The experimental sequence included laser desorption/electron impact Fourier transform mass spectrometry and direct-mode observation over a narrow mass range. Perfluorotributylamine was used as internal calibrant. Errors were about 1 ppm.     

多处理器芯片体系结构研究

随着超大规模集成电路工艺和超级计算技术的发展，作者认为在单个芯片内集成多处理器系统将成为可能。本文详细讨论了多处理器芯片的分类和结构，着重阐述了同构型多处理器芯片的主要研究方向，并对同构型多处理器的可行性作出了分析。     

A NEW ALGORITHM FOR ADAPTIVE LATTICE FILTERAND ITS APPLICATION IN THE SPEECH LINEARPREDICTIVE SYNTHESIS

In this paper, an adaptive line spectral pair filter is derived from an adaptive lattice filter. A least-mean-square(LMS) type adaptive algorithm used to calculate directly the line spectral pair(LSP) coefficients on a stage-by-stage basis is presented. Experimental results show that the algorithm has higher convergence rate and lower misadjustment as compared with the other algorithms. The LSP coefficients calculated by the algorithm have been used to carry out speech linear predictive synthesis, resulting in better results than PARCOR coefficients.     

Si1－xGex/Si量子阱发光材料的分子束外延生长及其结构研究

采用固源Si分子束外延,在较高的生长温度于Si(100)衬底上制备出Si1－xGex/Si量子阱发光材料。发光样品的质量和特性通过卢瑟福背散射、X射线双晶衍射及光致发光评估。背散射实验中观察到应变超晶格的反常沟道效应;X射线分析表明材料的生长是共度的、无应力释放的,结晶完整性好。低温光致发光主要是外延合金量子阱中带边激子的无声发射和横光学声子参与的激子复合。并讨论了生长温度对量于阱发光的影响。     

磷酸盐激光玻璃中铂颗粒密度与氧化还原平衡关系的研究

用吸收光谱法研究了Ｒ２Ｏ—ＢａＯ—Ｐ２Ｏ５系统磷酸盐激光玻璃中铂颗粒密度与铭的氧化还原平衡的关系。结果表明，玻璃中铂颗粒密度随平衡向右移动而减小；玻璃中平衡随熔炼气氛中氧分压增大、熔炼温度升高而向右移动，当足够大时，铂颗粒不能形成。     

The optical properties of planar waveguides in LiB3O5 crystals formed by Cu implantation

A planar optical waveguide has been formed in a LiB₃O₅ crystal using 6.0 MeV Cu⁺-ions with a dose of 1 × 10¹⁵ ions/cm² at room temperature. Possible propagating modes were measured at a wavelength of 633 nm using the prism-coupling method. The refractive index profiles of the waveguide were reconstructed by an effective refractive index method and the beam propagation method was used to investigate the properties of the propagation modes in the formed waveguide. The results suggest that the fundamental TE₀ and TM₀ modes may be well-confined and propagate a longer distance inside the waveguide. The implantation process was also simulated using the transport of ions in matter code (TRIM), which indicates that the nuclear energy deposition may be the main factor for the refractive index change.     

A Novel Athermal 40-Channel DWDM Multi/Demultiplexer Based on the Combination of AWGs and Interleaver

An athermal 40-channel dense wavelength-division-multiplexing multi/demultiplexer using a novel combination technology is proposed. It consists of one 1times4 100- to 400-GHz spacing interleaver filter and four sub-arrayed-waveguide gratings (AWGs). The temperature-dependent wavelength shift of the combined device is successfully suppressed to 0.058 nm in the -20degC to 70degC temperature range. Moreover, the combined device's adjacent crosstalk (typically -35 dB) is much better than conventional AWGs (typically -25 dB).     

Model-based automated extraction of microtubules from electron tomography volume.

We propose a model-based automated approach to extracting microtubules from noisy electron tomography volume. Our approach consists of volume enhancement, microtubule localization, and boundary segmentation to exploit the unique geometric and photometric properties of microtubules. The enhancement starts with an anisotropic invariant wavelet transform to enhance the microtubules globally, followed by a three-dimensional (3-D) tube-enhancing filter based on Weingarten matrix to further accentuate the tubular structures locally. The enhancement ends with a modified coherence-enhancing diffusion to complete the interruptions along the microtubules. The microtubules are then localized with a centerline extraction algorithm adapted for tubular objects. To perform segmentation, we novelly modify and extend active shape model method. We first use 3-D local surface enhancement to characterize the microtubule boundary and improve shape searching by relating the boundary strength with the weight matrix of the searching error. We then integrate the active shape model with Kalman filtering to utilize the longitudinal smoothness along the microtubules. The segmentation improved in this way is robust against missing boundaries and outliers that are often present in the tomography volume. Experimental results demonstrate that our automated method produces results close to those by manual process and uses only a fraction of the time of the latter.