Solving ML equations for 2-parameter Poisson-process models forungrouped software-failure data

Existence conditions are given for maximum likelihood (ML) parameter estimates for several families of 2-parameter software-reliability Poisson-process models. For each such model, the ML equations can be expressed in terms of one equation in one unknown. Bounds are given on solutions to these one equation problems to serve as initial intervals for search algorithms like bisection. Uniqueness of the solutions is established in some cases. Solutions are also tabulated for certain simple cases. Results are given for ungrouped failure data (exact times are available for all failures). ML estimation problems for such a situation are treated as limiting cases of problems based on failure times grouped into intervals of decreasing mesh     

Magnetometer spacing criterion for biomagnetic source currentimaging

A criterion for determining the maximum spacing between magnetometers for measuring the magnetic field is derived. A two-dimensional (2-D) filter model is employed to determine the maximum spatial frequency component present in the magnetic field that is above the spectral noise level. This maximum frequency component is then sampled at a rate greater than twice per period as indicated by the Nyquist criterion, yielding the required magnetometer spacing. It is shown that the rule-of-thumb employed in current clinical biomagnetic array systems, that the spacing between the coils should be approximately equal to the depth of the source, is adequate when the signal-to-noise power ratio is less than 28.4 (14.5 dB). The analysis also quantitatively demonstrates that reducing the separation between the measurement and source planes has a greater effect on the resolution than decreasing the noise level by the same factor. This result is important for employing high T_c superconductor magnetometers that allow thinner thermal insulating layers at the cost of higher thermal noise     

A comparison of two conformal methods for FDTD modeling

Two conformal finite-difference time-domain (FDTD) methods are considered, the contour path (CPFDTD) method of Jurgens et al. (see IEEE Trans. Antennas Propagat., vol.40, p.357, 1992) and the overlapping grid (OGFDTD) method of Yee et al. (see IEEE Trans. Antennas Propagat., vol.40, p.1068, 1992). Both TE and TM scattering from a two-dimensional (2-D), perfectly conducting circular cylinder are used to test the accuracy of the methods for curved surfaces. Also, TE and TM scattering from a 2-D, perfectly-conducting rotated square cylinder are used to test the accuracy for corners and edges. It is shown that the conformal method proposed by Yee et al. provide significant improvement in accuracy over the original FDTD algorithm for most of the geometries studied. However, implementation becomes more difficult as the geometries become more complex. The conformal method proposed by Jurgens et al. provide significant improvement in accuracy as well for most of the geometries studied. However, improvement does not occur for the TM case when the square cylinder is not aligned properly with the grid. Implementation of the CPFDTD method is relatively straightforward. For the majority of the cases studied, the OGFDTD method is more accurate than the CPFDTD method     

Tunable wavelength filters based on nonlinear optical interactionsin semiconductor amplifiers

A novel class of narrow-band tunable wavelength filters is proposed and evaluated. Wavelength selectivity of the proposed filters Is derived from the finite time response of an optical nonlinearity. The nonlinearity is gain saturation in semiconductor optical amplifier structures. The filters are shown to have very narrow passbands tunable over the entire semiconductor gain bandwidth. The key to filter implementation is a device configuration in which the wave-mixing products can be isolated from the amplified inputs. Three integrated optics compatible configurations are considered and shown to have high filter throughputs 34 to 180% and subangstrom bandwidths     

New concept for applying edge line phase-shifting masks to arbitrary mask layouts

This paper explains the principle of a method which avoids printing of phantom resist lines due to undesired intensity minima appearing on Cr-less edge line phase-shifting masks. The method combines principles of grey-tone lithography and attenuated phase-shifting masks to give, what we call, a Cr-Less Attenuated Phase-shifting mask (CLAP). Rules for generating a CLAP design and a paradigm setup of a CLAP mask are presented. The capabilities and possible limitations of the CLAP method based on simulated results for a standard wafer stepper setup using the SOLID lithography simulator are being assessed.     

Optimized partitioning of a wavelength distributed data interfacering network

A fiber optic ring network, such as fiber distributed data interface (FDDI), can be operated over multiple wavelengths on its existing fiber plant consisting of point-to-point fiber links. Using wavelength division multiplexing (WDM) technology, FDDI nodes can be partitioned to operate over multiple subnetworks, with each subnetwork operating independently on a different wavelength, and inter-subnetwork traffic forwarding performed by a bridge. For this multiwavelength version of FDDI, which we refer to as wavelength distributed data interface (WDDI), we examine the necessary upgrades to the architecture of a FDDI node, including its possibility to serve as a bridge. The main motivation behind this study is that, as network traffic scales beyond (the single-wavelength) FDDI's information-carrying capacity, its multiwavelength version, WDDI, can gracefully accommodate such traffic growth. A number of design choices exist in constructing a good WDDI network. Specifically, we investigate algorithms using which, based on prevailing traffic conditions, partitioning of nodes into subnetworks can be performed in an optimized fashion. Our algorithms partition the nodes into subrings, such that the total traffic flow in the network and/or the network-wide average packet delay is minimized     

Minimum-phase filter design from linear-phase startpoint viabalanced model truncation

A new practical design approach for minimum-phase FIR or IIR filters, setting out from a high dimensionality FIR linear-phase prototype is described. The novelty of this technique lies in overcoming the inherent problem of finding the roots of a high order polynomial with repeated and/or very closely clustered roots     

Phasenbeziehungen und Natriumionenleitung im quasi-binären System Na2SiF6/Na3AlF6

Phase Relations and Sodium Ion Conductivity within the Quasi-binary System Na₂SiF₆/Na₂AIF₆ . The phase diagram of the Na₂SiF₆/Na₃AlF₆ system has been determined by means of x-ray powder diffraction, thermal analysis and conductivity measurements in the sub-solidus region. Na₃AlF₆ accomodates up to 73 mol.-% Na₂SiF₆ maintaining the crystal structure type. The sodium ion conductivity increases by about five orders of magnitude upon doping Na₃AlF₆ with Na₂SiF₆.