State of polarization changes: Classification and measurement

We propose a standardization procedure that provides a convenient, quantitative and reproducible laboratory-based method for measuring the state of polarization (SOP) fluctuations produced by polarization varying devices. This method is based on the SOP distributions generated by commercial polarization scramblers. We show that these devices generate distributions of the maximum change of the SOP (in a given sample time) that follow Rayleigh statistics, which scale linearly with scrambling frequency and the sample time. We use this procedure to measure the SOP fluctuations in a short length of coiled fiber subject to mechanical perturbations.     

Nonlinearity analysis and optimization of HBTs for optical mixer designs

Two types of photo heterojunction bipolar transistor (HBT) to directly down-convert optical signals to electronic signals have been reported in the literature: a conventional photo-HBT in which light penetrates through the area of the base-collector junction and an HBT where light shines through the base-collector edge for higher conversion efficiency. Although the performance in relation to bias conditions has been published, the detailed analyses for identifying the parameters and bias conditions that provide optimum direct down-conversion have not been examined. This paper provides a full explanation of the operation of the down-conversion for both HBT configurations based on low-frequency analyses. Such information is useful for both understanding the nonlinear mechanisms involved and designing for maximum efficiency. In addition, a new circuit has been developed from the basic HBT down-conversion circuit that provides improved performance.     

Training and optimization of an artificial neural network controlling a hybrid power filter

A hybrid power compensator (HPC) consisting of a static VAr compensator and a dynamic compensator needs to be optimally controlled during the compensation of nonlinear loads. The HPC must be controlled to meet minimum requirements in terms of power factor and harmonic distortion, while at the same time minimizing its total cost. An artificial neural network (ANN) is used to control the HPC amidst a very dynamic power system environment. The performance of a reference ANN is evaluated while controlling an HPC connected to a typical nonlinear industrial load. The training and performance of the ANN is then optimized in terms of training set size, training set packing and ANN topology and the performance compared to the reference ANN. This paper highlights the importance of optimising the mentioned ANN parameters to achieve optimum ANN training and modeling accuracy. The results obtained reveals that the application of an ANN in controlling an HPC is feasible given that the ANN parameters are chosen appropriately.     

High-performance MIM capacitor using ALD high-k HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectrics

For the first time, we successfully fabricated and demonstrated high performance metal-insulator-metal (MIM) capacitors with HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectric using atomic layer deposition (ALD) technique. Our data indicates that the laminate MIM capacitor can provide high capacitance density of 12.8 fF//spl mu/m/sup 2/ from 10 kHz up to 20 GHz, very low leakage current of 3.2 /spl times/ 10/sup -8/ A/cm/sup 2/ at 3.3 V, small linear voltage coefficient of capacitance of 240 ppm/V together with quadratic one of 1830 ppm/V/sup 2/, temperature coefficient of capacitance of 182 ppm//spl deg/C, and high breakdown field of /spl sim/6 MV/cm as well as promising reliability. As a result, the HfO/sub 2/-Al/sub 2/O/sub 3/ laminate is a very promising candidate for next generation MIM capacitor for radio frequency and mixed signal integrated circuit applications.     

Hydrogen annealing effect on DC and low-frequency noise characteristics in CMOS FinFETs

The hydrogen annealing process has been used to improve surface roughness of the Si-fin in CMOS FinFETs for the first time. Hydrogen annealing was performed after Si-fin etch and before gate oxidation. As a result, increased saturation current with a lowered threshold voltage and a decreased low-frequency noise level over the entire range of drain current have been attained. The low-frequency noise characteristics indicate that the oxide trap density is reduced by a factor of 3 due to annealing. These results suggest that hydrogen annealing is very effective for improving device performance and for attaining a high-quality surface of the etched Si-fin.     

High-resolution photonics-based interference suppression filter with wide passband

A new topology for a photonic signal processor, which overcomes the basic recursive frequency response problem that limits the passband range, is presented. The structure is based on a new multiple-wavelength offset-cavity structure that is cascaded with a series of unbalanced delay line structures. This not only can synthesize a very narrow notch response with good shape factor but also permits a multifold extension of the free spectral range (FSR) and passband width. Results on the interference mitigation filter demonstrate a stopband of 1% of center frequency and a fourfold increase in the FSR and passband width, while also having a very small shape factor, in excellent agreement with predictions.     

Wavelength-tunable 40-GHz picosecond harmonically mode-locked fiber laser source

We demonstrate a novel 40-GHz mode-locked fiber laser that utilizes a single active device to provide both gain and mode-locking. The laser produces pulses as short as 2.2 ps, is tunable over a 27-nm band centered at 1553 nm, and exhibits long-term stability without cavity-length feedback control. The pulse train at 1556 nm was used in a 40-Gb/s transmission experiment over 45 km with a low 0.4-dB power penalty.     

Multilayer power printed structures suitable for controlling EMI noises generated in power converters

Electromagnetic interference (EMI) noises generated in power converters are diffused on the surface of conductors. This means influences occur from radiated EMI noises emitted from power transmission lines as well as conducted EMI noises transmitted from them. EMI noises diffusing on the surface of conductors are generally difficult to control using conventional concentrated constant theory. Thus, a new approach based on distributed constant circuit theory is needed in order to control EMI noises. A power converter structure to control EMI noises using multilayer power printed circuit technology is studied in this paper. A structure which can control EMI noises should simultaneously satisfy two conditions, i.e., one to shut down and one to attenuate EMI noises. The structure satisfying these conditions is studied through simulations using the Transmission-Line Modeling Method. The simulations show that the diffusion of EMI noises is controlled by dividing the flow of currents produced by EMI noises into the horizontal and perpendicular directions. That is, the horizontal current flow is controlled inside using the differences in the resistance produced from differences between inner and outer diameter of power transmission lines and the perpendicular current flow can be controlled by properly designing the thickness of the dielectric layer sandwiched between P-and N-power transmission lines with the symmetrical structure. Moreover, it is confirmed by simulations and experiments that the attenuation of EMI noises is affected by the width of the power transmission lines. It is expected that the results obtained in this paper can provide important rules when designing power converters with EMI noise control functions which use the multilayer power printed circuit technology.