Operation of a nonlinear optical loop mirror with orthogonally polarized waves in nonpolarization-preserving, single-mode fiber

We demonstrate stable operation of a NOLM using orthogonally polarized control and signal beams in nonpolarization-preserving, single-mode fiber. The NOLM can transcribe data from an optically incoherent input at one wavelength to a coherent output over a range of wavelengths. Operation of the NOLM without tuning for the input bit rate is possible over a range of bit rates from less than 1 Gb/s to more than 50 Gb/s.     

连续运转的掺钛蓝宝石激光器

本文报导一种连续波氩离子激光泵浦的掺钛蓝宝石激光器。在氩离子激光功率(全谱线)为10.45瓦且仅用一组腔镜时,获得最大平均功率超过1000mW、调谐范围750～850nm的掺钛蓝宝石激光输出。     

Check! a generic and specific industrial inspection tool

The authors present an overview of an `inspection and control' package to perform automatic quality control of industrial components, specifically electronic circuit boards. This application has grown out of a set of tools designed initially to aid the development of point distribution models (PDMs) and grey-level models (GLMs) pioneered at the Wolfson Image Analysis Unit in Manchester. These models are both generic and specific. Generic, because they can be applied to most image classification problems; specific, because they aim at the full interpretation of the variability of the objects to be modelled. The underlying vision processing techniques are based on statistical pattern matching. Two synergetic approaches have been followed. The system is trained to recognise the components from either their shape or their grey level appearance or both     

A novel four-point bend test for strength measurement of opticalfibers and thin beams. II. Statistical analysis

In the first part of this work, a novel implementation of the well-known four-point bend test is described that determines the strength of thin beams and optical fibers by measuring the loading pin displacement, rather than the applied load. This paper extends the analysis of the nonlinear bending behavior to account for the stochastic nature of strength. A statistical analysis is presented that determines the effective tested length in bending and the tension to bending strength ratio. Results are given for both surface and volume flaws as well as for specimens of both circular and rectangular section. Strength measurements on a deliberately weakened silica optical fiber are consistent with the predictions of the analysis     

Control of photoresist properties: a Kalman filter based approach

The photolithography step in the semiconductor manufacturing process becomes increasingly critical as linewidths decrease for the next generation of integrated electronics. It therefore becomes necessary to reduce variations in photoresist parameters such as resist film thickness and photoactive compound concentration during manufacture. In this paper, we present a simple feedback scheme for accurately regulating these parameters. Our approach involves obtaining a simple, static process model the coefficients of which are recursively adjusted based on previous wafer measurements. We use this adaptive model to determine appropriate input setpoints for the next wafer. The effectiveness of this scheme in reducing process drift is exhibited by experimental data. Our results supports the widespread contention that modern feedback control offers the promise of improving the semiconductor manufacturing processes, often with relative ease and minimal capital cost     

High-T/sub 0/ strain-compensated InGaAsSb-AlGaAsSb quantum-well lasers emitting at 2.43 /spl mu/m

Strain-compensated InGaAsSb-AlGaAsSb quantum-well (QW) lasers emitting near 2.5 /spl mu/m have been grown by solid-source molecular beam epitaxy. The relatively high arsenic composition causing a tensile strain in the Al/sub 0.25/GaAs/sub 0.08/Sb barriers lowers the valence band edge and the hole energy level, leading to an increased hole confinement and improved laser performance. A 60% external differential efficiency in pulsed mode was achieved for 1000-/spl mu/m-long lasers emitting at 2.43 /spl mu/m. A characteristic temperature T/sub 0/ as high as 163 K and a lasing-wavelength temperature dependence of 1.02 nm//spl deg/C were obtained at room temperature. For 2000 /spl times/ 200 /spl mu/m/sup 2/ broad-area three-QW lasers without lateral current confinement, a low pulsed threshold of 275 A/cm/sup 2/ was measured.     

Impact of Preferential P-Diffusion Along the Grain Boundaries on Fine-Grained Polysilicon Solar Cells

Thin-film polysilicon solar cells are a promising low-cost alternative for bulk silicon solar cells due to their reduced material thickness. Recently, we showed that the use of an amorphous silicon/polycrystalline silicon heterojunction emitter instead of a diffused homojunction emitter led to a boost in the open-circuit voltage by 90 mV. Now, we present a full evidence that shows that this improvement is related to the absence of dopant smearing along the grain boundaries. By using scanning spreading resistance microscopy, we found an enlargement of the junction area by a factor of five in case of a homojunction. The tips of the dopant spikes represent lowly doped areas with an enhanced recombination.     

Selective spatial localization of the atom displacements in one-dimensional hybrid quasi-regular (Thue-Morse and Rudin-Shapiro)/periodic structures

We have studied the vibrational frequencies and atom displacements of one-dimensional systems formed by combinations of Thue-Morse and Rudin-Shapiro quasi-regular stackings with periodic ones. The materials are described by nearest-neighbor force constants and the corresponding atom masses. These systems exhibit differences in the frequency spectrum as compared to the original simple quasi-regular generations and periodic structures. The most important feature is the presence of separate confinement of the atom displacements in one of the parts forming the total composite structure for different frequency ranges, thus acting as a kind of phononic cavity.     

A high-stability fiber amplifier source for the fiber opticgyroscope

We demonstrate an erbium-doped fiber amplifier (EDFA) source for the fiber gyroscope with an overall mean wavelength stability of four parts per million. This source, which amplifies the gyroscope signal before detection, is shown to be more stable than a similar single-pass source in a standard configuration. The effects of varying the fiber temperature, pump power, pump wavelength, gyroscope feedback power and signal polarization state on the output mean wavelength are individually explored. Experimental results are in excellent agreement with simulations