Measurement of PLL phase error caused by power supply noise

The measurement of the accumulated phase error of phase-locked loops (PLLs) in microprocessor systems is discussed. A system which creates controlled power supply noise and measures the PLL response is described. Examples of the use of this technique are shown for a PLL used in a 400 MHz microprocessor     

Optical detection of NO3 and NO2 in “pure” HNO3 vapor,the liquid-phase decomposition of HNO3

Flowing and static gas-phase samples of HNO₃ in O₂ and N₂ were analyzed by long-path ultraviolet/visible (UV/VIS) spectroscopy to reveal the presence of both NO₂ and NO₃, the concentrations of which were calculated using differential absorption cross sections. NO₂ is produced predominantly by the heterogeneous decomposition of HNO₃, whereas NO₃ is generated in the gas phase by the thermal decomposition of N₂O₅, a product of the self-disproportionation of liquid HNO₃. © 1993 John Wiley & Sons, Inc.     

Enhanced electron emission from phosphorus-doped diamond-cladsilicon field emitter arrays

Undoped and phosphorus (P)-doped diamond-clad Si field emitter arrays have been successfully fabricated using microwave plasma chemical vapor deposition (MPCVD) technology. The electron emission from the blunt diamond-clad microtips are much higher than those for the pure Si tips with sharp curvature due to a lower work function. Furthermore, the characteristics of emission current against applied voltage for the P-doped diamond-clad tips show superior emission at lower field to the undoped ones. After the examination of Auger electron spectroscopy (AES) and electrical characteristics of as-grown diamond, such a significant enhancement of the electron emission from the P-doped diamond-clad tips is attributed to a higher electron conductivity and defect densities     

Short-pulse, eye-safe Nd:YAG laser using cavity-dumping

A short-pulse 1.444-μm laser based on Nd:YAG technology has been demonstrated. The 1.444-μm is eye-safe. With the cavity-dump technique, a pulse of 50 m× and 14 ns was obtained. The beam quality was excellent with an M² of 1.6 by the use of a telescopic resonator. Silicon-window polarizers were used to suppress the 1.06-μm radiation but showed 1.444-μm absorption as well     

Radiation and scattering from ferrite-tuned cavity-backed slotantennas: theory and experiment

A three-dimensional finite-element method hybridized with the spectral/spatial domain method of moments is presented for the analysis of ferrite-tuned cavity-backed slot antennas. The cavity, which is partially filled with magnetized ferrite layers, is flush mounted on an infinite ground plane with possible dielectric or magnetic overlay. The antenna operates primarily in the ultrahigh-frequency band. The finite-element method is used to solve for the electric-field distribution inside the cavity, whereas the spectral-domain approach is used to solve for the exterior region. An asymptotic extraction of the exponential behavior of the Green's function followed by a spatial evaluation of the resulting integral is used to improve computational speed. Radar cross section, input impedance, return loss, gain, and efficiency of ferrite-tuned cavity-backed slots (CBS) are calculated for various biasing conditions. Numerical results are compared with experimental data     

Ultralow-voltage boron-doped diamond field emitter vacuum diode

A boron-doped diamond field emitter diode with ultralow turn-on voltage and high emission current is reported. The diamond field emitter diode structure with a built-in cap was fabricated using molds and electrostatic bonding techniques. The emission current versus anode voltage of the capped diamond emitter diode with boron doping, sp² content, and vacuum thermal electric (VTE) treatment shows a very low turn-on voltage of 2 V. A high emission current of 1 μA at an anode voltage of less than 10 V can be obtained from a single diamond tip. The turn-on voltage is significantly lower than comparable silicon field emitters     

Small-signal modeling and control of the quasi-square-wave boostconverter

Sampled-data techniques are used to examine the dynamic characteristics and closed-loop performance of the quasi-square-wave boost converter. Direct duty-ratio control and current-mode control are considered. With direct duty-ratio control, the system poles remain well damped under all load conditions, and there is no zero in the control-to-output transfer function. Good closed-loop performance is therefore achieved. Under current-mode control, the requirement for a stabilizing ramp is seen to depend on load conditions, and the achievable voltage control-loop bandwidth is smaller than that using direct duty-ratio control; however, there is a significant reduction in the magnitude of the DC source to output-voltage frequency response     

Thickness and temperature dependence of subsidiary absorption thresholds in yttrium-iron-garnet thin films

The microwave subsidiary absorption threshold in tangentially magnetized yttrium-iron-garnet (YIG) films was measured as a function of the static magnetic field, film thickness and decrease in the 0.3–3 μm range is observed. The effect is explained quantitatively by using modified Damon-Eshbach dispersion relations which take into account exchange interactions.

The effect of temperature on h_crit, the smallest threshold field amplitude, in the 250<T< 450 K temperature range can be expressed by an empirical relationship h_crit M_s(T)^-1.6 where M_s is the saturation magnetization. This h_crit vs M_s relationship is similar to that obtained for the magnetization dependence of parallel pump thresholds in Li-Ti ferrite compounds.     

Performance of the PAC optical packet network

For multiuser packet communications with unpredictable user demands (e.g., in a local or metropolitan area network), coordination and control of access to the frequency-division multiplexing (FDM) channels are difficult. B. Glance (J. Lightwave Technol., vol.10, pp.1323-1328, Sep 1992) proposed using a simple protection-against-collision (PAC) circuit to solve this media access problem and achieve full optical connectivity. The PAC system has the potential to interconnect hundreds of ports, each transmitting at several gigabits per second. Performance aspects of the PAC optical packet network are discussed here. The delay-throughout performance of this network is analyzed for uniform traffic patterns. The results show that in geographically distributed applications the maximum achievable throughput (normalized to the transmission rate) is typically between 0.4 and 0.5 per channel. In a centralized switch the (normalized) maximum achievable throughput can approach 0.8 per channel