Influence of the intensity of gg irradiation on the photoluminescence of GaAs:Te

The influence of gg irradiation (⁶⁰Co) of various intensities (P _γ≈1.7−7.5kGR/h) on the photoluminescence of GaAs:Te single crystals [n ₀=(1.2–2.3×10¹⁸ cm⁻³] is investigated. Together with the known photoluminescence impurity bands (hν _max≈1.2 eV and/or hν _max≈1.35 eV) and edge band (hν _max≈1.51 eV), new bands are also observed in the spectra at hν _max≈1.3 eV and hν _max≈1.48 eV. The observed effects are attributed to radiation-stimulated ordering of the donor impurity and deep impurity centers. Fiz. Tekh. Poluprovodn. 32, 38–39 (January 1998)     

Design aspects of planar and conventional SMPS transformer: a cost benefit analysis

The intent of this paper is to design a high-frequency transformer that is to be incorporated into the DC/DC pulsewidth-modulated switch-mode power supplies by two different technical approaches: a conventional wound-coil magnetic using copper wires, and a planar magnetic with layered copper tracks on laminated printed circuit board. Comparisons will be made between the two approaches in terms of profile: mounting height and surface area, and performance: power losses and efficiency. Other indicators like temperature rise and leakage inductance that causes electromagnetic interference, and cost, materials, and process fluency are also to be looked into. A sandwiched configuration for primary and secondary windings is proposed for the planar type. Issues arising and typical phenomena encountered will be discussed in detail. Primarily, the dominating factor in performance, cost effectiveness, or circuit compactness that restrains the choice of a particular type is to be evaluated.     

Designer's casebook-bridge-controlled duty-cycle oscillator withgrounded capacitor

A circuit that uses the parallel connection of a Schmitt-trigger-type multivibrator and a voltage-controlled current source is proposed. The circuit was developed for use with integrated silicon sensors. The operation of the circuit is described     

Variation of the temperature factor of models on a ballistic range

A technique for variation of the temperature factor of free-flight models by varying their initial temperature is described. An experiment on a ballistic range is carried out with a free-flying supersonic blunt cone with a half-angle of 15° at a Mach number of 2.3. The flow at the cone base is studied in the transition range (from the laminar to turbulent flow) of Reynolds numbers. The base flow pattern is determined from the shadowgraphs of the flow about the models. The drag coefficient of the blunt cone at a zero angle of attack is found by processing trajectory data. It is found that the near wake geometries and the drag coefficients of the models tested at the laboratory temperature and a temperature of 120 K differ. Explanations of this effect are given.     

Gas solubility of carbon dioxide in poly(lactic acid) at high pressures: Thermal treatment effect

The sorption of carbon dioxide in glassy Poly(lactic acid) (PLA) films was studied by quartz crystal microbalance (QCM) at high pressures. Two thermal treatments, melted and quenched, were performed in PLA with two different L:D contents, 80:20 and 98:2, films and compared with a third thermal protocol, annealed, and used in a previous work. The results obtained show that for pressures higher than 2 MPa, the carbon dioxide solubility is larger in PLA 80:20 than in PLA 98:2, indicating that the L:D plays a dominant role on this property. The thermal treatments only affect the gas solubility in PLA 98:2. Sorption isotherms at temperatures 303, 313, and 323 K, below the glass transition temperature of the polymer, and pressures up to 5 MPa were measured and analyzed with three different models, the dual‐mode sorption model, the Flory–Huggins equation, and a modified dual‐mode sorption model where the Henry's law term was substituted by the Flory–Huggins equation. This last model performs especially well for CO₂ in PLA 80:20, due to the convex upward curvature of the solubility isotherms for that system. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 616–625, 2007