Hydrogen annealing effect on DC and low-frequency noise characteristics in CMOS FinFETs

The hydrogen annealing process has been used to improve surface roughness of the Si-fin in CMOS FinFETs for the first time. Hydrogen annealing was performed after Si-fin etch and before gate oxidation. As a result, increased saturation current with a lowered threshold voltage and a decreased low-frequency noise level over the entire range of drain current have been attained. The low-frequency noise characteristics indicate that the oxide trap density is reduced by a factor of 3 due to annealing. These results suggest that hydrogen annealing is very effective for improving device performance and for attaining a high-quality surface of the etched Si-fin.     

High-resolution photonics-based interference suppression filter with wide passband

A new topology for a photonic signal processor, which overcomes the basic recursive frequency response problem that limits the passband range, is presented. The structure is based on a new multiple-wavelength offset-cavity structure that is cascaded with a series of unbalanced delay line structures. This not only can synthesize a very narrow notch response with good shape factor but also permits a multifold extension of the free spectral range (FSR) and passband width. Results on the interference mitigation filter demonstrate a stopband of 1% of center frequency and a fourfold increase in the FSR and passband width, while also having a very small shape factor, in excellent agreement with predictions.     

Wavelength-tunable 40-GHz picosecond harmonically mode-locked fiber laser source

We demonstrate a novel 40-GHz mode-locked fiber laser that utilizes a single active device to provide both gain and mode-locking. The laser produces pulses as short as 2.2 ps, is tunable over a 27-nm band centered at 1553 nm, and exhibits long-term stability without cavity-length feedback control. The pulse train at 1556 nm was used in a 40-Gb/s transmission experiment over 45 km with a low 0.4-dB power penalty.     

Joint scheduling and power control supporting multicasting in wireless ad hoc networks

This paper addresses the problem of power control in a multihop wireless network supporting multicast traffic. We face the problem of forwarding packet traffic to multicast group members while meeting constraints on the signal-to-interference-plus-noise ratio (SINR) at the intended receivers. First, we present a distributed algorithm which, given the set of multicast senders and their corresponding receivers, provides an optimal solution when it exists, which minimizes the total transmit power. When no optimal solution can be found for the given set of multicast senders and receivers, we introduce a distributed, joint scheduling and power control algorithm which eliminates the weak connections and tries to maximize the number of successful multicast transmissions. The algorithm allows the other senders to solve the power control problem and minimize the total transmit power. We show that our distributed algorithm converges to the optimal solution when it exists, and performs close to centralized, heuristic algorithms that have been proposed to address the joint scheduling and power control problem.     

Multilayer power printed structures suitable for controlling EMI noises generated in power converters

Electromagnetic interference (EMI) noises generated in power converters are diffused on the surface of conductors. This means influences occur from radiated EMI noises emitted from power transmission lines as well as conducted EMI noises transmitted from them. EMI noises diffusing on the surface of conductors are generally difficult to control using conventional concentrated constant theory. Thus, a new approach based on distributed constant circuit theory is needed in order to control EMI noises. A power converter structure to control EMI noises using multilayer power printed circuit technology is studied in this paper. A structure which can control EMI noises should simultaneously satisfy two conditions, i.e., one to shut down and one to attenuate EMI noises. The structure satisfying these conditions is studied through simulations using the Transmission-Line Modeling Method. The simulations show that the diffusion of EMI noises is controlled by dividing the flow of currents produced by EMI noises into the horizontal and perpendicular directions. That is, the horizontal current flow is controlled inside using the differences in the resistance produced from differences between inner and outer diameter of power transmission lines and the perpendicular current flow can be controlled by properly designing the thickness of the dielectric layer sandwiched between P-and N-power transmission lines with the symmetrical structure. Moreover, it is confirmed by simulations and experiments that the attenuation of EMI noises is affected by the width of the power transmission lines. It is expected that the results obtained in this paper can provide important rules when designing power converters with EMI noise control functions which use the multilayer power printed circuit technology.     

Analogue switch for very low-voltage applications

A new analogue switch suitable for operation at very low-voltage supply in a standard CMOS technology is presented. The proposed switch is based on 'quasi-floating-gate' transistors and has a simple and compact structure. For illustrative purposes, two sample-and-hold circuits operating from a single supply voltage close to the threshold voltage of a transistor, and using the proposed technique, are presented. Experimental results obtained from prototypes in a 1.5 /spl mu/m CMOS technology are provided.     

An investigation of sugar extraction methods and the use of microwave power for date syrup processing: efficiency and color related considerations.

This study investigates the effect of extraction methods on the color of date syrup and the potential use of microwave power for syrup processing. Sugar solutions were extracted from dates by boiling, soaking and blending. Color and sugar content of the extracted solutions were measured, and the percentage of sugar extracted form the total fruit sugar determined. Boiling was found to be the most efficient method of extraction whereby 74% of total samples sugar was extracted. In contrast, only 54.2% of fruit sugar was extracted by blending and 42% by soaking. In addition, solutions extracted by soaking and blending had a foaming problem in the subsequent concentration process. The extraction method had no effect on the product final color. The extracted solution was concentrated using two heating methods: conventional and microwave heating at a 600 W capacity and a frequency of 2450 MHz applied at three power levels: 10, 7, and 6. In the heating process, 180 minutes were needed to achieve a 77% degrees Brix using convective heating, while it took 81, 138, and 166 minutes of microwave heating at power level 10, 7, and 6, respectively to achieve the same concentration. Water activity of the syrup was measured within a sugar content range of 50 to 80% degrees Brix and the sugar concentration at which the product is shelf stable was determined at 76%.     

Nondiffusive weak localization in two-dimensional systems with spin-orbit splitting of the spectrum

The effect of spin splitting caused by structural asymmetry (Rashba’s contribution) and bulk asymmetry (Dresselhaus’s contribution) on the magnetoconductance of two-dimensional structures with high mobility of charge carriers is studied. The theory of weak localization with regard to both of the contributions is developed. The theory is valid in the entire region of classically low magnetic fields for arbitrary relations between the frequencies of spin precession and elastic collisions. The suppression of the correction for antilocalization is demonstrated in the case of equal contributions of structural anisotropy and bulk anisotropy to the spin splitting. The effect of the contribution, cubic in the wave vector, to the spin splitting on the quantum magnetoresistance is studied.     

Bandpass filters with reconfigurable transmission zeros using varactor-tuned tapped stubs

In this letter, bandpass filters with one or two tunable transmission zeros are proposed. The reconfigurable transmission zeros are implemented through varactors in combination with tapped quarter-wavelength stubs. Based on mixed mode simulations including EM simulation and circuit simulation, the proposed filters were designed and fabricated on low-cost FR4 board. The measurement results verified the design concepts.