Improvement of AlGaInP light emitting diode by sulfide passivation

The brightness of AlGaInP light emitting diodes (LEDs) has been raised by a factor of 1.12 at 20 mA by sulfide passivation. Meanwhile, the sulfide also can decrease leakage current of AlGaInP LEDs at -2 V to nearly one thousandth of that in the as-fabricated device. The possible causes for the brightness increase of AlGaInP LEDs after sulfide treatment including surface roughness, reduction of Fresnel loss, and effective injection of carriers were demonstrated.     

An adaptive p-persistent MAC scheme for multimedia WLAN

The letter proposes an adaptive p-persistent-based (APP) medium access control (MAC) scheme for the IEEE 802.11e distributed WLAN supporting multimedia services. The APP MAC scheme adaptively gives differentiated permission probabilities to transmission stations which are in different access category and with various waiting delay. Simulation results show that the APP MAC scheme can improve the performance of multimedia WLAN, such as small voice packet dropping probability, low delay variation, and high system throughput, compared to conventional MAC algorithms     

Bandpass filters with reconfigurable transmission zeros using varactor-tuned tapped stubs

In this letter, bandpass filters with one or two tunable transmission zeros are proposed. The reconfigurable transmission zeros are implemented through varactors in combination with tapped quarter-wavelength stubs. Based on mixed mode simulations including EM simulation and circuit simulation, the proposed filters were designed and fabricated on low-cost FR4 board. The measurement results verified the design concepts.     

Transient response of ARROW VCSELs under external optical feedback

The effect of external optical feedback on the transient response of antiresonant reflecting optical waveguide (ARROW) vertical-cavity surface-emitting lasers (VCSELs) is studied. It can be shown that the proper design of ARROW can suppress the excitation of high-order transverse leaky mode as well as increase the critical feedback strength so that stable high-power single-mode operation of VCSELs can be obtained even under the influence of strong external optical feedback.     

Feasibility analysis of phonon lasers

We identify the main reason impeding coherent generation of phonons in solid state - the inherently high density of phonon states. Based on the results of our analysis we formulate a set of conditions that may make phonon lasing practical and point out the most promising mechanism of phonon lasing: LO/spl rarr/LA+TO in InP. We then develop a complete set of phonon laser equations and evaluate the threshold, output power and efficiency of phonon lasers based on InP MESFET. We show that one can obtain high-power 1.26-THz coherent phonon emission with pump power as small as a few milliwatts and up to 5% slope efficiency. Potential applications are also discussed.     

异步DS-CDMA系统中基于矩阵点除算法的DOA估计

针对异步DS-CDMA系统中的多用户环境,本文提出了一种低复杂度的DOA估计算法——矩阵点除算法。该算法通过对感兴趣信息的逐次分离,实现了DOA的逐路径估计。算法具有两方面显著优势:(1)克服了传统的DOA估计算法在路径总数大于天线阵元数时不能工作这一缺陷:(2)避免了计算复杂的特征值分解运算,大大降低了算法复杂度。仿真实验验证了算法的有效性。     

Effect of Fog and Clouds on the Image Quality in Millimeter Communications

The effect of fog and clouds in millimeter communication is discussed, and the attenuation caused by fog and clouds is reviewed. Signal-to-noise ratio (SNR) of image is derived using relating models of fog and clouds attenuation. According to the relation of image quality and its signal-to-noise ratio, the system behavior is forecasted theoretically. It is shown that the signal-to-noise ratio of receiver at certain transmitter power is inverse with radio wave frequency, from about 70dB at 10GHz to 48dB for fog and 49dB for clouds. The image quality of received signal at certain transmitter power is inverse with radio wave frequency, from about 7 grade at 10GHz to 5.27 grade for fog and 5.37 grade for clouds. The above calculated results are consistent with experimental results.     

30.4 nm光电成像系统分辨率的初步实验研究

本文基于微通道板MCP(Microchannel Plate)探测器件设计一套成像系统，用于对波长为30．4nm的极紫外EUV(Extreme Ultraviolet)光进行成像．结果获得了一宽度为3mm的狭缝的像，实验测得490μm的成像系统的空间分辨率，并分析了影响系统分辨率的各种因素及为提高系统分辨率所应采取的措施．     

热作模具钢表面激光堆焊耐磨合金层的研究

本文主要通过在H13钢上用大功率CO_2激光束进行堆焊,阐述了激光堆焊工艺变化对堆焊组织和性能的影响,在本试验条件下,得到了高密度弥散金属化合物组织的激光堆焊层,平均硬度为HV800,与基体呈冶金结合,耐磨性比H13模具钢提高149%。