Ultratrace determination of cadmium by cold vapor atomic absorption spectrometry after preconcentration with a simplified cloud point extraction methodology

A simplified micelle-mediated extraction methodology for the preconcentration of ultratrace levels of cadmium as a prior step to its determination by cold vapor atomic absorption spectrometry (CV-AAS) has been developed. The methodology is based on the cloud point extraction (CPE) of cadmium at pH 8 by using the non-ionic surfactant polyethyleneglycolmono-p-nonylphenylether (PONPE 7.5) without adding any chelating agent. Cadmium cold vapor was generated from 2 ml of the extracted surfactant-rich phase by means of sodium tetrahydroborate (3%, w/v) as a reducing agent and hydrochloric acid (0.2 mol l⁻¹) as a carrier solution. Several important variables that affect the cloud point extraction and cold vapor cadmium generation efficiency were investigated and optimized. The preconcentration of only 50 ml of solution in the presence of 0.06% (v/v) PONPE 7.5 gives an enhancement factor of 62. The calibration graph using the preconcentration system was linear in the range of 4-100 ng l⁻¹ with a correlation coefficient of 0.9992. Detection limit (3 s) obtained in the optimal conditions was 0.56 ng l⁻¹. The relative standard deviation (R.S.D.) for six replicate determinations at 20 ng l⁻¹ Cd level was 3.2%. The proposed method was successfully applied to the ultratrace determination of cadmium in water samples.     

Mitigation of mutual interference in IEEE 802.15.4-based wireless body sensor networks deployed in e-health monitoring systems

Wireless Networks - One of the main issues experienced in wireless body sensor networks (WBSNs) is the destructive impacts of “mutual interference” caused by neighboring WBSNs on each...     

Toward manageable middleboxes in software‐defined networking

Software‐defined networking (SDN) acts as a centralized management unit, especially in a network with devices that operate under the transport layer of the OSI model. However, when a network with layer 7 middleboxes (MBs) is considered, current SDNs exhibit limitations. As such, to achieve a real‐centralized management unit, a new architecture is required that decouples the data and control planes of all network devices. In this report, we propose such a complementary architecture to the current SDN in which SDN‐enabled MBs are included along with contemporary SDN‐enabled switches. The management unit of this architecture improves network performance and reduces routing cost by considering the status of the MBs during flow forwarding. This unit consists of the following two parts: an SDN controller (SDNC) and a middlebox controller (MBC). The latter selects the best MBs for each flow and the former determines the best path according to its routing algorithm and provides information via the MBC. The results show that the proposed architecture improved performance because the utilization of all network devices including MBs is manageable.     

Synthesis and analytical application of a novel tetradentate N(2)O(2) Schiff base as a chromogenic reagent for determination of nickel in some natural food samples

A novel sensitive chromogenic reagent, N,N′-bis(3-methylsalicylidene)-ortho-phenylene diamine (MSOPD), has been synthesized and used in the spectrophotometric determination of nickel. At pH 8, MSOPD can react with nickel ion at room temperature to form a 1:1 complex. The apparent molar absorptivity is 9.5 × 10⁴ l mol⁻¹ cm⁻¹ at 430 nm. Beer's low is obeyed over the range 0-1.0 × 10⁻⁵ M of nickel with a detection limit of 1.36 × 10⁻⁸ M. The relative standard deviation for measurement of 3.41 × 10⁻⁶ M nickel is 1.3% (n = 10). The method has successfully been applied to determination of trace amounts of nickel in some natural food samples.     

A new family of bis-tetrazole (BIZOL) BINOL-type ligands

The synthesis and characterization of 5-(1-(2-(1H-tetrazole-5-yloxy)naphthalen-1-yl)naphthalen-2-yloxy)-1H-tetrazole (BIZOL) as the first bis-tetrazole BINOL-type ligands is described.     

Protein separation and surfactant control of electroosmotic flow in poly(dimethylsiloxane)-coated capillaries and microchips

A thermally pyrolyzed poly(dimethylsiloxane) (PDMS) coating intended to prevent surface adsorption during capillary electrophoretic (CE) [Science 222 (1983) 266] separation of proteins, and to provide a substrate for surfactant adsorption for electroosmotic mobility control was prepared and evaluated. Coating fused-silica capillaries or glass microchip CE devices with a 1% solution of 100 cSt silicone oil in CH2Cl2, followed by forced N2 drying and thermal curing at 400 degrees C for 30 min produced a cross-linked PDMS layer. Addition of 0.01 to 0.02% Brij 35 to a 0.020 M phosphate buffer gave separations of lysozyme, cytochrome c, RNase, and fluorescein-labeled goat anti-human IgG Fab fragment. Respective plates/m typically obtained at 20 kV (740 V cm(-1)) were 2, 1.5, 1.25, and 9.4-10(5). In 50 mM ionic strength phosphate, 0.01% Brij 35 running buffer, the electroosmotic flow observed was about 25% of that in a bare capillary, and showed no pH dependence between pH 6.3-8.2. Addition of sodium dodecylsulfate (SDS) or cetyltrimethylammonium bromide (CTAB) to this running buffer allowed ready control of electroosmotic mobility, mu(eo). Concentrations of SDS between 0.005 to 0.1% resulted in mu(eo) ranging from 3 to 5 x 10(-4) cm2 V(-1) s(-1). Addition of 1 to 2.3 x 10(-4)% (2.7-6.3 microM) CTAB caused flow reversal. CTAB concentrations between 3.5 x 10(-4) and 0.05% (0.0014-1.37 mM) allowed control of mu(eo) between -1 x 10(-4) and -5.0 x 10(-4) cm2 V(-1) s(-1). For both surfactants the added presence of 0.01% Brij 35 provided slowly varying changes in mu(eo) with charged surfactant concentration.     

Interaction of Dioxovanadium(V) with Alanine, Alanylalanine, and Alanylglycine

The stability constants of the systems dioxovanadium(V) with alanylalanine, alanylglycine, and alanine have been determined in aqueous solution in 0.8 pH 5 at 25°C and 0.1 mol-dm^–3 (NaClO₄), using a combination of potentiometric and spectrophotometric techniques. The compositions of the formed complexes were determined and it was shown that dioxovanadium(V) forms two mononuclear 1:1 and 1:2 species with alanine of the type VO₂L and VO₂L₂ ^–, and two mononuclear 1:1 complexes with alanylpeptides of the type VO₂HL and VO₂L^–.     

Effects of Final State Interactions in Pure Annihilation Decay of B+ → D+K0*

The decay of the B ⁺ meson to the D ⁺ and K ⁰* mesons is a pure annihilation decay. For this reason, in the framework of the quantum chromodynamics factorization (QCDF) approach, this decay has a small amplitude and a small branching ratio. In this research we find that, before the D ⁺ and K ⁰* mesons are produced in the final states, pair mesons such as D _s ⁺* and D _s ⁺ρ⁰ are produced. The intermediate-state mesons via the exchange of K ⁰(K ⁰*) and D ⁺(D ⁺*) go to the D ⁺ and K ⁰* final state mesons. However we calculate the B ₊ → D ⁺ K ⁰* decay in two different frameworks. The first framework is the QCDF method and the second one is final state interaction (FSI). The experimental branching ratio of B ₊ → D ₊ K ⁰* decay is less than 3 × 10^–6, and our results obtained by the QCDF method and FSI are (0.35 ± 0.04) × 10^–6 and (2.94 ± 0.10) × 10^–6, respectively.     

Trace determination of manganese(II) by temperature-controlled/assisted ionic liquid-based dispersive liquid-phase microextraction and electrothermal atomic absorption spectrometry

A microextraction method, namely temperature-controlled/assisted ionic liquid-based dispersive liquid-phase microextraction (DLPME) for manganese(II) determination in environmental water samples is presented. Manganese(II) was extracted from aqueous solution into an ionic liquid (IL) after complexation with 1-(2-thiazolylazo)-2-naphthol (TAN) and directly introduced for electrothermal atomic absorption spectrometry (ETAAS) determination. Several factors that might affect ETAAS signal and extraction efficiency, such as pyrolysis and atomization temperature; and pH adjustment, concentration of TAN, extraction time, volume of IL and stirring rate were studied. Within optimal experimental conditions, the detection limit (3σ), the quantification limit (10σ), the enrichment factor and the relative standard deviation for five replicate determinations at 0.5 μg L^?1 of manganese(II) were calculated as 0.023 μg L^?1, 0.076 μg L^?1, 58.7 and 6.3 %, respectively. The presented method was also successfully applied to the determination of manganese(II) in real samples. The main benefits of the method are simplicity, low cost, rapidity, high recovery, powerful extraction efficiency and the proposed approach is free of volatile organic solvents.