Limited-trial Chase decoding

Chase decoders permit flexible use of reliability information in algebraic decoding algorithms for error-correcting block codes of Hamming distance d. The least complex version of the original Chase algorithms uses roughly d/2 trials of a conventional binary decoder, after which the best decoding result is selected as the final output. On certain channels, this approach achieves asymptotically the same performance as maximum-likelihood (ML) decoding. In this correspondence, the performance of Chase-like decoders with even less trials is studied. Most strikingly, it turns out that asymptotically optimal performance can be achieved by a version which uses only about d/4 trials.     

Hot carrier analysis in low-temperature poly-Si thin-film transistors using pico-second time-resolved emission microscope

We have analyzed degradation of N-channel thin-film-transistor (TFT) under dynamic stress using a pico-second time-resolved emission microscope. We have successfully detected emission at pulse fall edge for the first time. Emission intensity increased with the decrease of pulse fall time. As the degradation depended on the pulse fall time, this dependence clearly illustrates that hot electrons are the dominant cause of the degradation under dynamic stress. Based on these dependences, we proposed a model considering electron traps in the poly-Si.     

SiGe VCOs operating up to 88 GHz, suitable for automotive radar sensors

VCOs fully integrated in an SiGe preproduction technology are presented. By cutting interconnection lines a wide frequency range can be covered, up to 88.4 GHz. Special effort has been made to meet the demands for 77 GHz automotive radar. In the corresponding tuning range from 75.3 to 79.6 GHz, an output power of about 11 dBm (with -2.2 dBm potential measurement uncertainty) was achieved for each of the two complementary outputs, i.e. in total 14 dBm. The phase noise is about -94 dBc/Hz at 1 MHz offset frequency.     

Effect of thermal annealing on optical and photoelectric properties of microcrystalline hydrogenated silicon films

The effect of thermal annealing in the temperature range T _a=300–600°C of films of microcrystal-line hydrogenated silicon (μc-Si:H) lightly doped with boron on the spectral dependences of the absorption coefficient (α) at photon energies hν=0.8–2.0 eV, dark conductivity (σ_d), and photoconductivity (Δσ_ph) was studied at room temperature. With increasing annealing temperature, a nonmonotonic variation of α (at hν<1.2 eV), σ_d, and Δσ_ph was observed. The data obtained are attributed to a change in the concentration of electrically active impurities and formation of defects, caused by hydrogen effusion and bond restructuring at high annealing temperatures.     

On the synergy between electrical and photonic switching

This article focuses on the values of electrical switching vs. photonic switching in the context of telecom transport networks. In particular, we show that the requirement of providing agility at the optical layer in the face of traffic forecast uncertainties is served better through photonic switching. On the other hand, some of the network-level functions, such as fast protection, subwavelength aggregation, and flexible client connectivity, require electrical switching. We further argue that additional values are achieved with hybrid photonic and electrical switching, which do not exist when either of these options is used in isolation.     

Bandpass filters with reconfigurable transmission zeros using varactor-tuned tapped stubs

In this letter, bandpass filters with one or two tunable transmission zeros are proposed. The reconfigurable transmission zeros are implemented through varactors in combination with tapped quarter-wavelength stubs. Based on mixed mode simulations including EM simulation and circuit simulation, the proposed filters were designed and fabricated on low-cost FR4 board. The measurement results verified the design concepts.     

Towards intelligent dressing

The aim of this article is to state the principles of an intelligent monitoring and control system for the grinding machine, comprising the dressing process as well as grinding stability.     

Self-oscillating dimmable electronic ballast

This paper presents a simple alternative for an electronic ballast operating in self-sustained oscillating mode with dimming capability for fluorescent lamps. A simple modification in one of the gate drivers side circuit allows the lamp to dim without compromising the simplicity, reliability, and low cost which characterize the self-oscillating electronic ballast (SOEB). A qualitative analysis is presented to explain the behavior of the proposed self-oscillating electronic ballast with dimming feature. In addition, the stability and the key equations for the design are derived using the extended Nyquist criterion and describing function method. Experimental results from two 40-W electronic ballasts are presented to demonstrate the performance and to validate the analysis carried out.     

A military perspective on small unmanned aerial vehicles

In recent years, advancements in three technology areas, microelectronics, MEMS sensors, and GPS receivers, have allowed small UAVs to overcome critical deficiencies and become practical for insertion into the military mainstream. The maturation and commercialization of these technologies have resulted in readily available components that have decreased in both size and cost, to the point where truly low-cost, highly capable, small UAVs are possible. In particular, inertial devices such as MEMS accelerometers and angular rate sensors, pressure sensors, and magnetometers have reached the point where they are reliable, accurate, and affordable. These devices allow the determination of vehicle state with the precision required to enable autonomous flight. In addition, advanced microelectronic devices, such as digital signal processors, field programmable gate arrays, and microcontrollers have enabled sophisticated flight control functions, including fully autonomous flight using GPS waypoints. In combination, these advances have allowed small UAVs such as Pointer, Raven, and Dragon Eye to move into full-scale production and continue to allow the progression of UAVs into smaller and smaller packages. To address several of the deployment issues connected with small UAVs, a gun-launched version, along with the underpinning technologies, is under development. This device represents a clear departure from conventional UAVs with several clear advantages; however, it also contains severe design challenges, as well as test and evaluation dilemmas. An option of this type is envisioned not as a replacement for conventional small UAVs but rather as an augmenting capability.     

A 1-V 10.7-MHz switched-opamp bandpass /spl Sigma//spl Delta/ modulator using double-sampling finite-gain-compensation technique

A 1 V switched-capacitor (SC) bandpass sigma-delta (/spl Sigma//spl Delta/) modulator is realized using a high-speed switched-opamp (SO) technique with a sampling frequency of up to 50 MHz, which is improved ten times more than prior 1 V SO designs and comparable to the performance of the state-of-the-art SC circuits that operate at much higher supply voltages. On the system level, a fast-settling double-sampling SC biquadratic filter architecture is proposed to achieve high-speed operation. A low-voltage double-sampling finite-gain-compensation technique is employed to realize a high-resolution /spl Sigma//spl Delta/ modulator using only low-DC-gain opamps to maximize the speed and to reduce power dissipation. On the circuit level, a fast-switching methodology is proposed for the design of the switchable opamps to achieve a switching frequency up to 50 MHz. Implemented in a 0.35-/spl mu/m CMOS process (V/sub TP/=0.82 V and V/sub TN/=0.65 V) and at 1 V supply, the modulator achieves a measured peak signal-to-noise-and-distortion ratio (SNDR) of 42.3 dB at 10.7 MHz with a signal bandwidth of 200 kHz, while dissipating 12 mW and occupying a chip area of 1.3 mm/sup 2/.