Routing Correlated Data with Fusion Cost in Wireless Sensor Networks

In this paper, we propose a routing algorithm called minimum fusion Steiner tree (MFST) for energy efficient data gathering with aggregation (fusion) in wireless sensor networks. Different from existing schemes, MFST not only optimizes over the data transmission cost, but also incorporates the cost for data fusion, which can be significant for emerging sensor networks with vectorial data and/or security requirements. By employing a randomized algorithm that allows fusion points to be chosen according to the nodes' data amounts, MFST achieves an approximation ratio of 5/4log(k + 1), where k denotes the number of source nodes, to the optimal solution for extremely general system setups, provided that fusion cost and data aggregation are nondecreasing against the total input data. Consequently, in contrast to algorithms that only excel in full or nonaggregation scenarios without considering fusion cost, MFST can thrive in a wide range of applications     

Novel method for simultaneous formation of wires and vias of a printed circuit board using nanoporous body

A new type of a flexible printed circuit board with landless vias is developed using a novel method called interconnection via nanoporous structure (INPS). This method can make wires and vias of the printed circuit board simultaneously by a single photo-exposure process. A new photo-induced selective plating method was used to impregnate a nanoporous substrate with copper, and a new photomask was designed, which constitutes of a completely vacant large hole for via and aggregation patterns of very fine holes for wire. Because of the simple process, the INPS board is characterized by landless vias and very fine circuit. Owing to the structure, it is also characterized by flexibility and detachable wires.     

A comparative study of DPSK and OOK WDM transmission over transoceanic distances and their performance degradations due to nonlinear phase noise

We have compared experimentally the transmission performance of return-to-zero differential phase-shift keying (RZ-DPSK) with RZ-ON-OFF keying (OOK), nonreturn-to-zero differential phase-shift keying (NRZ-DPSK), and NRZ-OOK for 100/spl times/10-Gb/s transmission with a spectral efficiency of 0.22 b/s/Hz over transoceanic distances. The Q degradation of the RZ-DPSK after transmission over 9180 km was 3 dB greater than that of RZ-OOK. The experimental results clearly showed the major cause of degradation for DPSK is not cross-phase modulation but self-phase modulation. The calculated nonlinear phase noise, i.e., the Gordon-Mollenauer effect, agreed with the experimental results. A distributed-Raman-amplifier assisted erbium-doped-fiber-amplified transmission line acted well in reducing the nonlinear phase noise.     

Graph-theoretic construction of low-density parity-check codes

This article presents a graph-theoretic method for constructing low-density parity-check (LDPC) codes from connected graphs without the requirement of large girth. This method is based on finding a set of paths in a connected graph, which satisfies the constraint that any two paths in the set are either disjoint or cross each other at one and only one vertex. Two trellis-based algorithms for finding these paths are devised. Good LDPC codes of practical lengths are constructed and they perform well with iterative decoding.     

Extracting Light from Polymer Light‐Emitting Diodes Using Stamped Bragg Gratings

In this paper, we describe a method for increasing the external efficiency of polymer light‐emitting diodes (LEDs) by coupling out waveguided light with Bragg gratings. We numerically model the waveguide modes in a typical LED structure and demonstrate how optimizing layer thicknesses and reducing waveguide absorption can enhance the grating outcoupling. The gratings were created by a soft‐lithography technique that minimizes changes to the conventional LED structure. Using one‐dimensional and two‐dimensional gratings, we were able to increase the forward‐directed emission by 47 % and 70 %, respectively, and the external quantum efficiency by 15 % and 25 %.     

Planar lightwave integrated circuits with embedded actives for board and substrate level optical signal distribution

This paper explores design options for planar optical interconnections integrated onto boards, discusses fabrication options for both beam turning and embedded interconnections to optoelectronic devices, describes integration processes for creating embedded planar optical interconnections, and discusses measurement results for a number of integration schemes that have been demonstrated by the authors. In the area of optical interconnections with beams coupled to and from the board, the topics covered include integrated metal-coated polymer mirrors and volume holographic gratings for optical beam turning perpendicular to the board. Optical interconnections that utilize active thin film (approximately 1-5 /spl mu/m thick) optoelectronic components embedded in the board are also discussed, using both Si and high temperature FR-4 substrates. Both direct and evanescent coupling of optical signals into and out of the waveguide are discussed using embedded optical lasers and photodetectors.     

Reliability studies of MOCVD TiSiN and EnCoRe Ta(N)/Ta

Passivated single damascene copper SiO₂ damascene lines were evaluated in combination with TiSiN and Ta(N)/Ta diffusion barriers. Leakage current, breakdown and time-dependent dielectric breakdown properties were investigated on a wafer level basis for temperatures ranging between room temperature and 150 °C. It is found that the leakage performance of the wafers with a TiSiN barrier is better at room temperature, but at 150 °C the performance levels out with Ta(N)/Ta. Time-dependent dielectric breakdown measurements at 150 °C show that the lifetime of the interconnect is higher with the selected Ta(N)/Ta barrier than for TiSiN.     

Intelligent process analytics for CRM

Many organisations use decision models in their processes such as tables or trees to provide decision support to their operational divisions. For example, in fault management, customer contact centre operators usually use a decision model in the form of prescribed interviews. Based on the answers given by customers, the operator navigates through the decision model to reach an assessment of the problem. In order to achieve customer satisfaction and operational excellence, it is very important to constantly monitor the performance of a decision model not only on an overall level, but also on the level of individual decisions. In this paper we present a configurable business process analytics tool, known as the intelligent Universal Service Management System, that constantly monitors decision data and is capable of optimising the decisions based on high-level business objectives. We explain the various features of the software and show how it can be used to optimise decision processes. We also show how we can easily provide a customised version to monitor the performance of provision processes.     

Optical-transmission characteristics of optical-fiber cables and installed optical-fiber cable networks for WDM systems

Many cables containing 1.3-/spl mu/m zero-dispersion single-mode (SM) optical fibers are installed in trunk and access networks. Recently, there have been a number of studies on wavelength-division-multiplexing (WDM) systems designed to increase transmission capacity and flexibility. If we can construct WDM systems using SM optical-fiber cable networks designed to transmit using wavelengths in the 1.3-/spl mu/m window (O-band), this will prove very effective in reducing construction costs. It is therefore important to examine the wavelength dependence of the transmission characteristics of SM optical-fiber cables and networks that have already been installed and in which several optical fibers are joined. In this paper, we describe the measured optical characteristics of SM optical-fiber cables and installed optical-fiber cable networks at various wavelengths. The optical characteristics were stable in the 1.46 to 1.625-/spl mu/m wavelength range and we confirmed that the installed SM optical-fiber cable networks could be used for WDM system applications.     

Analytic models for the latency and steady-state throughput of TCP Tahoe, Reno, and SACK

Continuing the process of improvements made to TCP through the addition of new algorithms in Tahoe and Reno, TCP SACK aims to provide robustness to TCP in the presence of multiple losses from the same window. In this paper we present analytic models to estimate the latency and steady-state throughput of TCP Tahoe, Reno, and SACK and validate our models using both simulations and TCP traces collected from the Internet. In addition to being the first models for the latency of finite Tahoe and SACK flows, our model for the latency of TCP Reno gives a more accurate estimation of the transfer times than existing models. The improved accuracy is partly due to a more accurate modeling of the timeouts, evolution of cwnd during slow start and the delayed ACK timer. Our models also show that, under the losses introduced by the droptail queues which dominate most routers in the Internet, current implementations of SACK can fail to provide adequate protection against timeouts and a loss of roughly more than half the packets in a round will lead to timeouts. We also show that with independent losses SACK performs better than Tahoe and Reno and, as losses become correlated, Tahoe can outperform both Reno and SACK.