氢化丁苯共聚物结构的核磁共振波谱表征Ⅱ.微观结构的定量计算

在氢化丁苯共聚物¹³C-NMR谱脂肪碳部分谱带归属的基础上,根据各谱带的主要来源,推导出六个二单元浓度的计算公式。计算出二单元、一单元的相对含量,各结构单元的数均序列长度、嵌段含量和其它结构参数。加氢前后的¹H-和¹³C-NMR谱的组成计算结果基本一致。初步探讨了作为粘度指数改进剂的氢化丁苯共聚物微观结构与性能的关系,为合成提供了依据。     

The correlation of texture and magnetic properties in Co-Cr films

This investigation focuses on the correlation between the crystallographic orientation of grains with respect to magnetic properties in Co-Cr films. Based on a distribution measured for the (0002) crystallographic pole densities, modified formulae describing the texture were used to calculate the coercivity Hc, the squareness ratio Rs (Mr⊥/TMs) and the anisotropy field Ha for Co-Cr films. In general, calculated values for the coercive force He agreed well with the measured values. The calculated Rs⊥. values were much larger than the measured ones, however, indicating that the influence of the demagnetizing field and the magnetostriction on the orientation of the magnetization cannot be neglected. On leave from Institute of Computing Technology, Academia Sinica, P.O.Box 2704-6, Beijing, P.R. China.     

A hybrid spreading/despreading function with good SNR performancefor band-limited DS-CDMA

Code-division multiple-access (CDMA) implemented with direct-sequence spread spectrum (DS/SS) signaling is a promising multiplexing technique for cellular telecommunications services. The efficiency of a direct-sequence spread-spectrum code-division multiple-access (DS-CDMA) system depends heavily on the shape of the spectrum of the spread signal. Maximum efficiency is obtained with an ideal brick-wall bandpass spectrum. There are two approaches toward achieving such a spectrum. One is to use a simple spreader that produces a broad spectrum and then follow it with a precise, high order filter to band limit the spectrum. A second approach, which is the approach taken in this paper, is to use a spreader that produces a spectrum close to the ideal spectrum and then employ a simple filter to control the out-of-band power. The proposed spreader/despreader is based on a simple hybrid function and can be easily implemented. An analysis provides a compact expression for the signal-to-noise ratio (SNR) of a RAKE receiver. The expression includes the effects of baseband, intermediate frequency (IF) and RF filtering as well as the effects of the spectral densities of the spreading/despreading functions. The analysis shows that the proposed spreader/despreader yields superior performance over a conventional pseudo noise (PN) spreading/despreading mechanism     

可配置非幂方分频器的全新设计方法

本文采用基于计数空间完全划分和周期插入控制计数过程方法设计了非幂方分频器,采用这种全新思路设计的非幂方分频器分频范围很宽,分频输出对后续分频支持好,非常适用于通讯接口中的波特率时钟设计.此外,这种设计思路对系统定时电路和节拍控制电路设计也有一定的借鉴意义.     

关于一类二次哈密尔顿系统在二次扰动下的极限环个数问题

本文研究了一类具有两个鞍点和一个中心的通用二次哈密尔顿向量场在二次扰动下的三参数开折，证明极限环的最小上界为２。     

Automatic fault detection, isolation, and recovery in transparentall-optical networks

Network fault identification is an important network management function, which is closely related to fault management and has an impact on other network management functions such as configuration management, and performance management. This paper investigates fault surveillance and fault identification mechanisms for a transparent optical network in which data travels optically from the source node to the destination node without going through any optical-to-electrical (O/E) or electrical-to-optical (E/O) conversion. Mechanisms and algorithms are proposed to detect and isolate faults such as fiber cuts, laser, receiver, or router failures. These mechanisms allow nonintrusive device monitoring without requiring any prior knowledge of the actual protocols being used in the data transmission     

玻璃陶瓷材料中Tm3+离子红外到蓝色上转换发光

系统研究了PbF2+GeO2+WO3ⅩⅣTmF3玻璃陶瓷材料中,在近红外光(1.06μm)激发下,Tm3+离子的发光特性.实验中观测到Tm3+离子的两组峰值位置分别在20920cm-1和22173cm-1的蓝色上转换发光,并证实这两组上转换发光分别与吸收三个和四个光子有关,同时建立了上转换发光的模型.为了选择最佳掺杂浓度,详细地测量了Tm3+离子峰值为20920cm-1的蓝色上转换发光强度与TmF3浓度的关系.     

非线性光纤方向耦合器孤子动力特性分析

利用变分方法,导出了双曲正割型光孤子在非线性光纤耦合器中传输时满足的动力学方程组,分析了该方程组的平衡点性态,讨论了光孤子的开关特性.指出参数|β|<2π.是能实现完全的开关操作的必要条件.     

溶胶-凝胶制备技术与新型催化材料Ⅲ.溶胶粒子表面修饰方法制备催化膜

提出用溶胶粒子表面修饰方法，结合溶胶凝胶技术制备无机催化膜．该方法的基本原理是利用合适的金属配合物在胶粒表面的吸附作用，经溶胶凝胶过程，将活性组分结合到无机膜中．实验测定结果表明：（ＮｉＥＤＴＡ）２－，ＶＯ－３，ＭｏＯ２－４，（Ｐｄ（ＮＨ３）４）２＋，ＰｄＣｌ２－４，ＰｔＣｌ２－６和ＲｈＣｌ３－６可用来修饰ＡｌＯＯＨ溶胶．以Ｐｄ／γＡｌ２Ｏ３催化膜的制备为例，经三次溶胶凝胶过程，可制得无裂缺的厚度为９μｍ的Ｐｄ／γＡｌ２Ｏ３催化膜，膜材料的平均孔直径为６ｎｍ，Ｐｄ被均匀地分布在膜的顶层，其平均粒径为２３ｎｍ．     

深亚微米MOSFET衬底电流的模拟与分析

利用器件模拟手段对深亚微米ＭＯＳＦＥＴ的衬底电流进行了研究和分析，给出了有效的道长度，栅氧厚度，源漏结深，衬底掺杂浓度以及电源电压对深亚微米ＭＯＳＦＥＴ衬底电流的影响，发现电源电压对深亚微米ＭＯＳＦＥＴ的衬底电流有着强烈的影响，热载流子效应随电源电压的降低而迅速减小，当电源电压降低到一定程度时，热载流子效应不再成为影响深亚微米ＭＯＳ电路可靠性的主要问题。