Strong visible PL from the nc-Si thin film by Ni silicide mediated crystallization

We studied the growth of nanocrystalline silicon (nc-Si) thin film exhibiting a strong room temperature photoluminescence (PL) at 1.81–2.003 eV. The amorphous silicon was crystallized by Ni silicide mediated crystallization (Ni SMC) and then Secco-etched to exhibit the PL. The PL peak energy and intensity increase with increasing the metal density on the a-Si because of the reduction in the grain size down to 2 nm. The photoluminescence energy and peak intensity depend strongly on the Secco etch time because the grain size is reduced by etching the grain boundaries.     

Possible triggering of solar activity to big earthquakes (Ms ≥ 8) in faults with near west-east strike in China

A big earthquake (Ms = 8.1) occurred at western Kunlun Mts gap on November 14, 2001. It is the biggest earthquake in China in the past 50 years and the only one with a magnitude bigger than 8 in China after Dangxiong Earthquake (M = 8) in Tibet in 1951. The big earthquake has drawn wide attention of scientists in seismological, geophysical, geological and astro-geodynamic circles. Scientists are interested in the occurrence regularity of the very big earthquakes and try to find out the fac…     

Correlation between Al2O3 particles and interface of Al-Al2O3 coatings by cold spray

Al-Al₂O₃ composite coatings with different Al₂O₃ particle shapes were prepared on Si and Al substrate by cold spray. The powder compositions of metal (Al) and ceramic (Al₂O₃) having different sizes and agglomerations were varied into ratios of 10:1 wt% and 1:1 wt%. Al₂O₃ particles were successfully incorporated into the soft metal matrix of Al. It was found that crater formation between the coatings and substrate, which is typical characteristic signature of cold spray could be affected by initial starting Al₂O₃ particles. In addition, when the large hard particles of fused Al₂O₃ were employed, the deep and big craters were generated at the interface between coatings and hard substrates. In the case of pure soft metal coating such as Al on hard substrate, it is very hard to get proper adhesion due to lack of crater formation. Therefore, the composite coating would have certain advantages.     

短脉冲激光尾流场中的前向Raman散射

用212维粒子模拟分析了前向Raman散射对激光尾流场加速电子的影响.前向Raman散射使脉冲长度在传播方向上被拉长，脉冲后沿变陡，产生的尾流场相速度明显减小，而且超热电子的最大动能明显小于理论估计值.此外激光频率整体向低频移动.     

Some sufficient conditions for oscillation of impulsive delay hyperbolic systems with Robin boundary conditions

This paper deals with the oscillation problems of delay hyperbolic systems with impulses. Some sufficient conditions for oscillations of impulsive delay hyperbolic systems with Robin boundary conditions are obtained and the criteria of oscillation of the systems are established.     

Coriolis耦合对Cl+H2→H+HCl非绝热反应的影响

使用含时波包方法 ,在Capecchi和Werner拟合的非绝热耦合势能面上 ,研究了Cl处在自旋轨道基态以及自旋轨道激发态时与H2 反应的活性 ,并且讨论了Coriolis耦合的影响 .计算了某些角动量时的反应几率 .计算结果显示 ,当Cl原子处在自旋轨道激发态与处在基态的H2 的反应活性很小 ,Coriolis耦合在这个反应中起了很小的作用 .     

紧急输送策略的线性规划模型

以美国南弗洛里达州递避飓风袭击为例建立了紧急输送情况下的线性规划模型。其中具体建立了以SCEPD(美国南弗洛里达州紧急情况预防部门)提出的公路反向，地区分块撤离，使用小路等三个最受人们关注的策略的模型。模型的灵敏度分析能很好地解释建立更多的临时避难所、限制车辆等策略对撤离的影响。在相近的环境下，中模型解得的结果很接近官方预测的结果，并且本的模型能对更广泛的情况进行分析．可给SCEPD提供一定参考。     

The Fabrication and Characterization of Single‐Component Polymeric White‐Light‐Emitting Diodes

By using Ni⁰‐mediated polymerization, we have systematically synthesized a series of fluorene‐based copolymers composed of blue‐, green‐, and red‐light‐emitting comonomers with a view to producing polymers with white‐light emission. 2,7‐Dibromo‐9,9‐dihexylfluorene, {4‐(2‐[2,5‐dibromo‐4‐{2‐(4‐diphenylamino‐phenyl)‐vinyl}‐phenyl]‐vinyl)‐phenyl}‐diphenylamine (DTPA), and 2‐{2‐(2‐[4‐{bis(4‐bromo‐phenyl)amino}‐phenyl]‐vinyl)‐6‐tert‐butyl‐pyran‐4‐ylidene}‐malononitrile (TPDCM) were used as the blue‐, green‐, and red‐light‐emitting comonomers, respectively. It was found that the emission spectra of the resulting copolymers could easily be tuned by varying their DTPA and TPDCM content. Thus with the appropriate red/green/blue (RGB) unit ratio, we were able to obtain white‐light emission from these copolymers. A white‐light‐emitting diode using the polyfluorene copolymer containing 3 % green‐emitting DTPA and 2 % red‐emitting TPDCM (PG3R2) with a structure of indium tin oxide/poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonic acid)/PG3R2/Ca/Al was found to exhibit a maximum brightness of 820 cd m^–2 at 11 V with Commission Internationale de L'Eclairage (CIE) coordinates of (0.33,0.35), which are close to the standard CIE coordinates for white‐light emission (0.33,0.33).