Phase-insensitive all-optical transistors based on second-ordernonlinearities

We demonstrate and compare two phase-insensitive all-optical transistors (AOT's) based on frequency-degenerate quadratic three-wave interactions. In particular, we demonstrate gain using KTP in a type II geometry. Both AOT's exploit the phase insensitivity inherent to three-wave parametric processes when only two fields are input, providing amplification of a small signal at the operating frequency via the interaction with a second-harmonic wave. The first scheme is based on successive up- and down-conversion (i.e., cascading) while the second relies on parametric down-conversion. We obtain gains of 5 and 160 in the two configurations, respectively, with a significant background and output coherent to the pump in the first case, no background and coherence between output and signal in the second     

Mode analysis of DFB SE lasers

This paper presents theoretical results on mode characteristics of surface-emitting (SE) lasers utilizing an active second-order grating section. Based on a coupled-mode approach, longitudinal modes and the associated space-harmonic transverse modes are calculated via a numerical technique. From these, the lasing-mode spectrum, near- and far-field patterns of the radiation mode, and the surface-emission power efficiency are obtained. Effects of the substrate reflector and the grating parameters are also investigated. Finally, comparisons are made with conventional, edge-emitting DFB lasers. The results indicate that with a suitable choice of structural parameter values, DFB SE lasers can be made to possess both the spectral discrimination of the conventional DFB lasers and the advantages of SE lasers at the same time and also that the second lowest longitudinal mode may be preferred over the fundamental longitudinal mode for many applications due to its symmetric field distribution     

On detecting the presence of fetal R-wave using the moving averagedmagnitude difference algorithm

An efficient algorithm detecting the presence of a fetal QRS complex is presented. The proposed fetal QRS detection method computes the averaged magnitude of the difference between the fetal ECG signal and the reference signal to detect the fetal QRS event. The detected fetal QRS complexes are exponentially averaged to generate the template signal which can track the slowly varying shape of the fetal ECG signal. As an effort to obtain improved detection performances, two approaches of normalizing the fetal ECG signal and the template are considered.     

Separation of screw-sensed particles in a homogeneous shear field

The Stokes motions of three-dimensional screw-sensed slender particles in a homogeneous shear field are investigated, including the effects of buoyancy. Conclusions are drawn about the possibility of achieving a separation of mixtures of right- and left-handed particles. The linearity of the Stokes equations allows complex flows to be solved by adding the effects of the several terms which describe the flow in which the particle is immersed. The homogeneous shear flow considered here consists of three such terms; solutions for a series of 12 unit motions are sufficient to determine the hydrodynamic resistance tensors. The forces and torques experienced by screw-sensed particles are calculated from these 51 resistance tensors, using slender-filament theory. The results allow an estimate of the range of buoyancy parameters for which gravitational sedimentation can be neglected. The fundamental component of the particle motion is a rotation, at approximately the same angular velocity as that of the fluid. Superimposed on this are variations, of large period, in the particle orientation. A phase plane analysis is used to find the terminal orientations. Very long calculation times are required for the phase portrait. An approximate method based on azimuthally-averaged equations is developed to avoid the requirements for long time integration.     

Complete joint weight enumerators and self-dual codes

We define the complete joint weight enumerator in genus g for codes over /spl Zopf//sub 2k/ and use it to study self-dual codes and their shadows. These weight enumerators are related to the theta series of the associated lattices and Siegel and Jacobi forms are formed from these series.     

Dual effects of fullerene doped to holographic polymer dispersed liquid crystals

Doping of conductive fullerene particles to the formulation of conventional holographic polymer dispersed liquid crystal‐induced dual effects of reducing both droplet coalescence and operating voltage. Fullerene induced an induction period which otherwise does not exist, followed by a gradual increase of diffraction efficiency to a saturation value being increased with increasing fullerene content. The increased diffraction efficiency was caused by the decreased droplet coalescence which was due to the hindered migration of LC by the fullerene particles. On the other hand, doped fullerene particles augmented the conductivity of polymer phase and hence the local electrical field imposed on LC droplet, which overcome the threshold for driving and reduced operating voltage and response times. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5590–5596, 2007     

Simulation and design methodology for a 50-Gb/s multiplexer/demultiplexer package

A 50 Gb/s package for SiGe BiCMOS 4:1 multiplexer and 1:4 demultiplexer targeting SONET OC-768 serial communication systems is introduced in this work. The package was designed to facilitate bit-error-rate tests and constructed with high-speed coaxial connectors, transmission lines on ceramic substrate, ribbon bonds for chip-to-package interconnects, and a metal composite housing. Numerical simulations were conducted to guide the package design, and both small signal measurements and operational tests were performed thereafter to verify the design and modeling concepts. To keep the model structure under the existing computing capability, the simulation was segmented into three sections - coaxial connector to transmission line, transmission line alone, and transmission line to ribbon bond, and then the results were assembled to predict the performance of the entire package. The package was operated up to 50 Gb/s with low degradation to input digital waveforms and free of error.     

Design and Experimental Characterization of Low‐Volume PM10/2.5/1.0 Trichotomous Sampler Inlet

This paper presents the development and laboratory evaluation of a PM10/2.5/1.0 trichotomous sampling inlet that consists of two main parts: a previously designed PM10 size‐selective inlet part and a PM2.5/1.0 two‐stage virtual impactor, which was newly fabricated and attached serially to the PM10 size selective inlet part. Particles are collected in three locations through the trichotomous sampling inlet to provide for not only particle concentration measurements of PM10, PM2.5 and PM1.0, but also those of PM2.5–10 and PM1.0–2.5.     

Assessment of thermal expansion coefficient of methylsilsesquioxane thin film

For the methylsilsesquioxane film whose optical birefringence is almost zero, it was recently reported that its vertical thermal expansion coefficient (CTE) was approximately one order of magnitude larger than the lateral CTE. Though the birefringence is not an absolute predictor of anisotropic behavior, the discrepancy in both the CTEs was so remarkable that it was essential to investigate whether the anisotropy was intrinsic property or not. If the effect of Poisson's ratio is considered in the calculation of the vertical CTE and when elastic modulus measured by surface acoustic wave spectroscopy is used in the assessment of the lateral CTE, both the CTEs are coincident with each other. Therefore, it can be concluded that the discrepancy in the CTEs can be attributed to a higher in‐plane polymer chain orientation but it can also arise from the misleadingly assumed modulus and Poisson's ratio. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3109–3120, 2006     

Validation of 3-D curved objects: CAD model and fabricatedworkpiece

This paper proposes a new method to describe and identify a 3-D curved object for the purpose of validating a fabricated object to the design specification. Curved 3-D objects are, in general, difficult to represent and identify because they lack distinct properties such as edges, planes, or cylindrical surfaces which are the building blocks in representing objects. In this paper, the authors propose to use principal axes of a 3-D object to establish a reference for the representation. A method of obtaining an inertia matrix from a 3-D range image is developed. The unique set of principal axes is obtained from the inertia matrix of an object with an arbitrary 3-D position and orientation, and the object can be described uniquely on these principal axes. On the principal axes, an object is described by a set of features describing the shape of the object such as spine, section size, section orientation, and section contraction. The features are used for comparing two objects for the validation purpose. The authors also propose a direct measure of similarity between two objects as a mean-squared difference of radii. As an experiment, two 3-D object models are designed through a CAD package, and fabricated objects are compared with the designed models for validation purposes