Analysis on plasma chemistry and particle growth in corona discharge process for NO/sub x/ removal using discrete-sectional method

The particle formation and growth combined with plasma chemistry in the pulsed corona discharge process (PCDP) to remove NO/sub x/ were analyzed by the discrete-sectional model. In the PCDP, most of the NO is converted into NO/sub 2/ and, later, into HNO/sub 3/ which reacts with NH/sub 3/ to form the NH/sub 4/NO/sub 3/ particle. In the beginning of the reactor, we have the high concentration of small size particles and, later, the particle size distribution in the reactor becomes bimodal with the large size and small size particles and, finally, becomes monodisperse with the large size particles. As the average electron concentration increases, it takes a shorter reactor length to remove the NO/sub x/. As the initial NO and H/sub 2/O concentrations decrease, the NH/sub 3/ is consumed more slowly to form the ammonium nitrates particles. As the averaged electron concentration and initial H/sub 2/O concentration increase, the large size particles grow more quickly and the particle size distribution becomes bimodal earlier. As the initial NO and NH/sub 3/ concentrations increase, the diameter of large size particles becomes larger by the faster coagulation between particles. The predicted NO/sub x/ conversion and particle size distribution were in close agreements with the published experimental results at the averaged electron concentration of 2/spl times/10/sup 5/ cm/sup -3/ in this study.     

A high-capacity broadband packet switch architecture based on a multilink approach

Broadband packet networks based on asynchronous transfer mode (ATM) are expected to provide a wide range of services, including motion video, voice, data and image. When these networks become prevalent, some applications such as motion video and high-speed LAN interconnections will place a very large bit rate requirement on the channels. Currently, the physical layer supported by the synchronous optical network (SONET) allows the transmission of up to 2.4 Gbit/s with the OC-48 optical interface. However, it is not feasible for the electronic packet switch to route packets at this rate on a single link. In this paper we present a design of a broadband packet switch that uses multiple links in parallel to realize a high-speed channel. This implementation permits the switch to operate at the lower link rate, which can be at 150 Mbit/s, while having the ability to support a virtual circuit at a higher rate (up to 2.4 Gbit/s). The main contribution of the design is that packet sequence on a channel is still maintained even though packets are allowed to use any of the links belonging to the same channel. Besides allowing the switch to function at a slower rate than the transmission channel rate, the implementation of the multilinks benefits from statistical multiplexing gain. Analytical results show the performance advantages of multilink design with respect to delay, throughput and packet loss probability.     

The effect of olefinic terminal chains on the mesomorphic properties of 4,4'-disubstituted diphenyldiacetylenes

New diphenyldiacetylenes of the type with A, B = H and/or F; m = 0, 1; n = 1-4; and X = C n H 2n + 1 , F, CF 3 or CN were synthesized and their mesomorphic properties determined by hot stage polarizing microscopy and DSC. When m = 0, all of these compounds showed only a nematic phase except when X = CF 3 when both nematic and smectic A phases were seen. Both clearing and melting temperatures were higher than those reported for substitution with the corresponding alkyl chains but the much larger increase in clearing temperatures produced considerably wider nematic phases. Eutectic mixtures of a few of these olefins yielded nematic materials also having much wider temperature ranges and higher clearing temperatures than the eutectic mixtures of the alkyl compounds, while retaining their high birefringence and low viscosities. Such materials are of interest for beam-steering devices.

Four of the diacetylenes with m = 1 ( A, B = H) were also prepared ( X = C 6 H 13 , F, n = 2, 3). When X was C 6 H 13 ( n = 2), the nematic range was smaller in the 2- than in the 1-olefin but wider than in the alkyl series. When X = F, either no nematic phase or a monotropic one was observed, whereas the 1-olefins gave a much wider nematic phase. Both transition temperatures were lower than those for the corresponding 1-olefin and alkyl analogues. The compound with X = C 6 H 13 and n = 2 had a melting temperature below room temperature.     

89-GHz fT room-temperature silicon MOSFETs

The authors report the implementation of deep-submicrometer Si MOSFETs that at room temperature have a unity-current-gain cutoff frequency (f_T) of 89 GHz, for a drain-to-source bias of 1.5 V, a gate-to-source bias of 1 V, a gate oxide thickness of 40 Å, and a channel length of 0.15 μm. The fabrication procedure is mostly conventional, except for the e-beam defined gates. The speed performance is achieved through an intrinsic transit time of only 1.8 ps across the active device region     

Control of high common mode voltage during transthoracicdefibrillation

A high common mode voltage (V_cm) relative to earth ground is produced on the myocardium during the delivery of a defibrillator pulse and can generate a differential error signal when potential gradients are recorded with bipolar electrodes and isolation amplifiers. The error signal is proportional to V_cm, and therefore, a reduction in V_cm improves the accuracy of the potential gradient data. Experiments were conducted on 5 dogs to determine whether V_cm can be controlled using a bridge circuit. The bridge circuit consisted of a 5 kΩ power rheostat in parallel with the transthoracic resistance of the dog. The variable contact of the rheostat was connected to earth ground, and by adjusting the rheostat, V_cm on the myocardium could be varied. In each dog, 20 A shocks were delivered through stainless steel transthoracic electrodes. Point contact electrodes sutured to the epicardium were used to measure V_cm. It was determined that V_cm could be reduced to approximately zero at a given electrode on the heart. In addition, for the 5 dogs studied, the maximum measured V_cm on the heart was only 10% of the transthoracic voltage when the bridge circuit was balanced for an interior point in the heart     

Computation of the average power pattern of a reflector antennawith random surface errors and misalignment errors

To specify manufacturing tolerances of a reflector antenna, various errors such as random surface errors and misalignment errors must be considered at one time because superposition of the effects of those errors may not hold. Based on the Rahmat-Samii's formulation (1983), a method for computing efficiently the average power pattern of a reflector antenna with those errors is presented. Simulation results show that superposition of the effects of errors does not generally hold and demonstrate how those errors degrade the peak-gain and sidelobe levels     

Preparation of enantiomerically pure (R)-2-butyryloxymethylglycidol by lipase-catalyzed asymmetric hydrolysis

Optically active epoxy alcohol, (R)-2-butyryloxymethylglycidol3 which is the precursor of a tert-alcohol chiral building block was obtained in high enantiomeric purity, 98.7% e.e., by lipase-catalyzed asymmetric hydrolysis using a phosphate buffer and organic co-solvent system in 95% of chemical yield.     

Precipitation and characterization of uniform submicrometer lead titanate particles. Part II: Reaction mechanism

The chemical mechanism of the precipitation of lead titanium peroxohydroxide particles in a solution of nitrilotriacetate (NTA) complexes of lead and titanium peroxo-hydroxide is envisioned as the interaction between cations of lead hydroxide and anions of polymeric titanium peroxo-hydroxide.     

Reduction of loading effect by tungsten etchback in a magneticallyenhanced reactive ion etcher

The plug loading effect occurring during the etchback of tungsten was investigated in a magnetically enhanced reactive ion etcher using SF ₆/Ar mixtures. It was found that while the plug loading effect is independent of varying SF₆/Ar flow rate ratio and magnetic field intensity, it is reduced under the condition of high selectivity of tungsten relative to TiN which was achieved at high chamber pressure and low RF power. It is proposed that when TiN is used as a glue layer, the W etch rate enhancement in the plug is mainly controlled by a local loading effect. Under the optimized etchback conditions the plug loss was successfully controlled without the tungsten residue left on severe topology     

Recent advances in theory and applications of scrambling techniquesfor lightwave transmission

This paper discusses recent advances in the theory and applications of scrambling techniques for digital lightwave transmission. It introduces the theories of sequence space and shift register generator (SRG) space which enable systematic analysis and mathematical manipulation of the behavior of sequences in general and the related SRG's. It discusses the behavior and realization of frame synchronous scrambling (FSS) and distributed sample scrambling (DSS) with emphasis on parallel sequences and the related parallel SRG's (PSRG). In addition, it describes self synchronous scrambling (SSS). Then the paper applies the theories to today's lightwave transmission systems by demonstrating practical parallel designs of FSS for SDH/SONET transmission, DSS for cell-based ATM transmission, and SSS for SDH-based ATM transmission. It finally considers how DSS can be used for scrambling of mixed isochronous and nonisochronous data in future high-speed data networks. The paper employs various new concepts and terminology, such as PSRG engine, generating vector discrimination matrix, (M,N) PSRG, sampling vector, correction vector, correction matrix, predictable scrambling concurrent sampling, and immediate correction