InGaAs（P）分别限制应变单量子阱激光器的优化设计

针对较常用的ＩｎＧａＡｓ（Ｐ）分别限制应变单量子阱激光器，给出了为得到最大净增益的优化设计参数。对于激射波长为１．５５μｍ的无应变激光器，最佳的光限制层波长为１．２４μｍ，厚度为１００ｎｍ。当阱材料引入压缩应变后．由于价带的有效状态密度减小，量子阱激光器的微分增益变大，阱深的增大对增大线性增益的效果更加明显．所以最佳光限制层的波长将变短，为１．２０μｍ     

气相色谱-质谱联用法测定维生素C泡腾片中的甜蜜素

采用气相色谱-质谱(GC-MS)选择离子监测法(SIM),建立了准确可靠、灵敏度高、快速简便的测定维生素C泡腾片中甜蜜素含量的新方法.样品中的甜蜜素衍生后用有机试剂提取,在选择离子模式下进行测定,以保留时间和特征离子比例进行定性,单离子定量.甜蜜素的线性范围为0.05-10mg/L,检出限为0.6mg/kg,回收率为90.5%-96.9%,相对标准偏差小于4.4%.方法分析所用时间短,结果准确可靠,选择性好,适用于维生素C泡腾片中甜蜜素含量的检验.     

Synthesis of TiO2–SiO2/polymer core–shell microspheres with a microphase‐inversion method

A novel microphase‐inversion method was proposed for the preparation of TiO₂–SiO₂/poly(methyl methacrylate) core–shell nanocomposite particles. The inorganic–polymer nanocomposites were first synthesized via a free‐radical copolymerization in a tetrahydrofuran solution, and the poor solvent was added slowly to induce the microphase separation of the nanocomposite and result in the formation of nanoparticles. The average particle sizes of the microspheres ranged from 70 to 1000 nm, depending on the reaction conditions. Transmission electron microscopy and scanning electron microscopy indicated a core–shell morphology for the obtained microspheres. Thermogravimetric analysis and X‐ray photoelectron spectroscopy measurements confirmed that the surface of the nanocomposite microspheres was polymer‐rich, and this was consistent with the core–shell morphology. The influence of the synthetic conditions, such as the inorganic composition and the content of the crosslinking monomer, on the particle properties was studied in detail. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3911–3920, 2006     

Effect of glass bead packing on the fibrillation of liquid‐crystalline polymer in polycarbonate

Polycarbonate (PC) was melt blended with small amount of liquid‐crystalline polymer (LCP) and various contents of glass beads (GB) having different diameters. The rheological measurements indicated that the GB addition increased the viscosity ratio and seemed unfavorable to the LCP fibrillation. However, the morphological observation showed that the LCP fibrillation was promoted by the GB addition and varied with the GB packing. With the increased GB packing by increasing the GB content and/or decreasing the GB diameter, LCP deformed from spheres and ellipsoids into stretched ellipsoids at lower shear rates and into long fibrils at higher shear rates. Although higher content of smaller GB jammed into the larger LCP droplets and inhibited the LCP fibrillation, very long LCP fibrils formed at higher shear rates at a high enough packing of GB. The relationship between GB packing and LCP fibrillation revealed two kinds of hydrodynamic effects of GB promoting the LCP fibrillation: at lower GB packing, the shear flow was enhanced by the high local shear between GB, in quantity; and for a high enough GB packing, the shear flow was changed, in quality, into elongational flow, which was more effective for the LCP fibrillation. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1020–1030, 2006     

仲态电子偶素湮没辐射能量的改进测量

用充氧气的气凝硅胶作仲态电子偶素源,用¹⁹²Ir精密γ能量作标准,以时间选择能谱仪和滑动比较法改进测量仲态电子偶素2γ湮没能量,得到hv=510995.34±0.69eV.经电子偶素结合能修正,得正、负电子对静止质量,与电子质量比较,表明正、负电子质量在1.4ppm内一致.     

面向对象方法在7号信令软件设计中的应用

随着交换技术的飞速发展，程控交换软件的规模越来越大，改动也越来越频繁，如何使代码对数据的改动具有相对的稳定性成为程控软件设计的一个首要问题。本文以ＣＣＳ７（７号公共信道信令）为例，从对象模型、动态模型、功能模型３个方面阐述了ＯＯ（面向对象）方法在ＣＣＳ７软件设计中的应用。这一方法，也可应用于程控软件的设计。     

Interaction of gravitational waves with a superconducting cylindrical antenna

In this paper we investigate the effects of gravitational waves (GW) on a superconducting cylindrical antenna (S-antenna). We suggest that the electric fields induced by GW of dimensionless amplitudeh - 10^–24 in the interior of existing cylindrical antenna might be detectable.     

树脂吸附法处理水杨酸甲酯生产废水的研究

采用吸附树脂NDA—99处理水杨酸甲酯生产废水，结果表明该树脂时废水中的5磺基水杨酸及水杨酸均具有良好的吸附—脱附性能．废水经预处理和吸附处理后，CODCr由57000-59000mg／L降至6300mg／L左右，去除率接近89％．用IBV8％NaOH 3BVH2O作脱附剂，在温度为60℃、流量为IBV／h的条件下，脱附率接近100％，树脂可重复使用．高浓度脱附液经酸化、浓缩、冷却结晶，可回收5—磺基水杨酸，回收率为95％左右。纯度为78％。     

Direct fourier reconstruction in fan-beam tomography

We consider the problem of reconstructing tomographic imagery from fan-beam projections using the direct Fourier method (DFM). Previous DFM reconstructions from parallel-beam projections produced images of quality comparable to that of filtered convolution back-projection. Moreover, the number of operations using DFM in the parallel-beam case is proportional to N2 log N versus N3 for back projection [3]. The fan-beam case is more complicated because additional interpolation of the nonuniformly spaced rebinned data is required. We derive bounds on the detector spacing in fan-beam CT that enable direct Fourier reconstruction and describe the full algorithm necessary for processing the fan-beam data. The feasibility of the method is demonstrated with an example. A key result of this paper is that high-quality imagery can be reconstructed from fan-beam data using the DFM in 0 (N2 log N) operations.