Optimal pilot waveform assisted modulation for ultrawideband communications

Ultrawideband (UWB) transmissions induce pronounced frequency-selective fading effects in their multipath propagation. Multipath diversity gains can be collected to enhance performance, provided that the underlying channel can be estimated at the receiver. To this end, we develop a novel pilot waveform assisted modulation (PWAM) scheme that is tailored for UWB communications. We select our PWAM parameters by jointly optimizing channel estimation performance and information rate. The resulting transmitter design maximizes the average capacity, which is shown to be equivalent to minimizing the mean-square channel estimation error, and thereby achieves the Crame/spl acute/r-Rao lower bound. Application of PWAM to practical UWB systems is promising because it entails simple integrate-and-dump operations at the frame rate. Equally important, it offers a flexible UWB channel estimator, capable of striking desirable rate-performance tradeoffs depending on the channel coherence time.     

On the physical and logical topology design of large-scale optical networks

We consider the problem of designing a network of optical cross-connects (OXCs) to provide end-to-end lightpath services to large numbers of label switched routers (LSRs). We present a set of heuristic algorithms to address the combined problem of physical topology design (i.e., determine the number of OXCs required and the fiber links among them) and logical topology design (i.e., determine the routing and wavelength assignment for the lightpaths among the LSRs). Unlike previous studies which were limited to small topologies with a handful of nodes and a few tens of lightpaths, we have applied our algorithms to networks with hundreds or thousands of LSRs and with a number of lightpaths that is an order of magnitude larger than the number of LSRs. In order to characterize the performance of our algorithms, we have developed lower bounds which can be computed efficiently. We present numerical results for up to 1000 LSRs and for a wide range of system parameters such as the number of wavelengths per fiber, the number of transceivers per LSR, and the number of ports per OXC. The results indicate that it is possible to build large-scale optical networks with rich connectivity in a cost-effective manner, using relatively few but properly dimensioned OXCs.     

The effects of nonlocal impact ionization on the speed of avalanche photodiodes

The nonlocal enhancement in the velocities of charge carriers to ionization is shown to outweigh the opposing effects of dead space, increasing the avalanche speed of short avalanche photodiodes (APDs) over the predictions of a conventional local model which ignores both of these effects. The trends in the measured gain-bandwidth product of two short InAlAs APDs reported in the literature support this result. Relatively large speed benefits are predicted to result from further small reductions in the lengths of short multiplication regions.     

High resistivity measurement of SiC wafers using different techniques

To establish fast, nondestructive, and inexpensive methods for resistivity measurements of SiC wafers, different resistivity-measurement techniques were tested for characterization of semi-insulating SiC wafers, namely, the four-point probe method with removable graphite contacts, the van der Pauw method with annealed metal and diffused contacts, the current-voltage (I-V) technique, and the contactless resistivity-measurement method. Comparison of different techniques is presented. The resistivity values of the semi-insulating SiC wafer measured using different techniques agree fairly well. As a result, application of removable graphite contacts is proposed for fast and nondestructive resistivity measurement of SiC wafers using the four-point probe method. High-temperature van der Pauw and room-temperature Hall characterization for the tested semi-insulating SiC wafer was also obtained and reported in this work.     

Analysis of feedback for higher order polarization-mode dispersion mitigation of NRZ 40-Gb/s optical transmission

First-order polarization-mode dispersion (PMD) compensation by means of a polarization controller and a differential delay line is not sufficient to guarantee error-free transmission for 40-Gb/s channels when higher order effects severely increase signal distortion. Higher order mitigation is possible by cascading more than one first-order block. However, only two-stage or three-stage devices remain simple enough to be actually controlled. The performance of such higher order PMD compensators is evaluated by means of numerical simulations. Two different feedback signals have been used, demonstrating that first-order and higher order PMD distortion of nonreturn-to-zero (NRZ) pulses at 40 Gb/s can be strongly mitigated for instantaneous values of the differential group delay (DGD) up to the bit slot, when the compensator is properly controlled.     

Miniature and tunable filters using MEMS capacitors

Microelectromechanical system (MEMS) bridge capacitors have been used to design miniature and tunable bandpass filters at 18-22 GHz. Using coplanar waveguide transmission lines on a quartz substrate (/spl epsiv//sub r/ = 3.8, tan/spl delta/ = 0.0002), a miniature three-pole filter was developed with 8.6% bandwidth based on high-Q MEMS bridge capacitors. The miniature filter is approximately 3.5 times smaller than the standard filter with a midband insertion loss of 2.9 dB at 21.1 GHz. The MEMS bridges in this design can also be used as varactors to tune the passband. Such a tunable filter was made on a glass substrate (/spl epsiv//sub r/ = 4.6, tan/spl delta/ = 0.006). Over a tuning range of 14% from 18.6 to 21.4 GHz, the miniature tunable filter has a fractional bandwidth of 7.5 /spl plusmn/ 0.2% and a midband insertion loss of 3.85-4.15 dB. The IIP/sub 3/ of the miniature-tunable filter is measured at 32 dBm for the difference frequency of 50 kHz. The IIP/sub 3/ increases to >50 dBm for difference frequencies greater than 150 kHz. Simple mechanical simulation with a maximum dc and ac (ramp) tuning voltages of 50 V indicates that the filter can tune at a conservative rate of 150-300 MHz//spl mu/s.     

End‐Capping as a Method for Improving Carrier Injection in Electrophosphorescent Light‐Emitting Diodes

The electronic properties, carrier injection, and transport into poly(9,9‐dioctylfluorene) (PFO), PFO end‐capped with hole‐transporting moieties (HTM), PFO–HTM, and PFO end‐capped with electron‐transporting moieties (ETM), PFO–ETM, were investigated. The data demonstrate that charge injection and transport can be tuned by end‐capping with HTM and ETM, without significantly altering the electronic properties of the conjugated backbone. End‐capping with ETM resulted in more closely balanced charge injection and transport. Single‐layer electrophosphorescent light‐emitting diodes (LEDs), fabricated from PFO, PFO–HTM and PFO–ETM as hosts and tris[2,5‐bis‐2′‐(9′,9′‐dihexylfluorene)pyridine‐κ²NC_3′]iridium(III ), Ir(HFP)₃ as the guest, emitted red light with brightnesses of 2040 cd m^–2, 1940 cd m^–2 and 2490 cd m^–2 at 290 mA cm^–2 (16 V) and with luminance efficiencies of 1.4 cd A^–1, 1.4 cd A^–1 and 1.8 cd A^–1 at 4.5 mA cm^–2 for PFO, PFO–HTM, and PFO–ETM, respectively.     

Modeling of a constant Voltage transformer

This paper presents a comprehensive nonlinear model of the controlled constant voltage transformer also known as the ferroresonant transformer. Saturation is a normal mode of operation for this device. This paper derives an equivalent electrical circuit that relates to the physical structure of a typical design. The level of detail includes winding resistances, continuously nonlinear magnetizing inductances, tapped windings, and leakage inductances. The paper describes methods to extract the winding resistances, leakage inductances, and hysteresis loops of the transformer and how to fit the latter into single-valued nonlinear functions. The paper compares computer simulation results of the model with those obtained analytically and experimentally. The results show that the derived circuit will be very useful for designers of the ferroresonant transformer, which is used in uninterruptible power supplies.     

Combined RLS-LMS initialization for per tone equalizers in DMT-receivers

In discrete multitone receivers, the classical equalizer structure consists of a (real) time domain equalizer (TEQ) combined with complex one-tap frequency domain equalizers. An alternative receiver is based on a per tone equalization (PTEQ), which optimizes the signal-to-noise ratio (SNR) on each tone separately and, hence, the total bitrate. In this paper, a new initialization scheme for the PTEQ is introduced, based on a combination of least mean squares (LMS) and recursive least squares (RLS) adaptive filtering. It is shown that the proposed method has only slightly slower convergence than full square-root RLS (SR-RLS) while complexity as well as memory cost are reduced considerably. Hence, in terms of complexity and convergence speed, the proposed algorithm is in between LMS and RLS.     

Steady-state operation of a high-voltage multiresonant converter in a high-temperature environment

Often scientific instruments on exploratory satellites are used to collect cosmic particles. These instruments, such as the Faraday cup, require a high-voltage regulated power source. On the proposed solar probe satellite there will be instruments which will collect cosmic particles close to the sun. Naturally temperature effects on the voltage regulator are a concern. Specifically power dissipation within the regulator must stay within stringent guidelines. The high-voltage regulator circuit is a resonant flyback topology with a dissipative series switch whose on resistance controls the output voltage level. The extreme temperatures in space will change the inductance of the flyback transformer which will affect the output voltage. State space analysis techniques are used to determine how the value of the transformer inductance and capacitance in the flyback converter affects the output voltage and consequently the power dissipated by the transformer and the switch. The accuracy of the analysis is verified by comparing results with those obtained from an experimental circuit. The results can then be used to help the designer chose nominal capacitance and inductance values that will work over the temperature range of interest.