A 1-V 10.7-MHz switched-opamp bandpass /spl Sigma//spl Delta/ modulator using double-sampling finite-gain-compensation technique

A 1 V switched-capacitor (SC) bandpass sigma-delta (/spl Sigma//spl Delta/) modulator is realized using a high-speed switched-opamp (SO) technique with a sampling frequency of up to 50 MHz, which is improved ten times more than prior 1 V SO designs and comparable to the performance of the state-of-the-art SC circuits that operate at much higher supply voltages. On the system level, a fast-settling double-sampling SC biquadratic filter architecture is proposed to achieve high-speed operation. A low-voltage double-sampling finite-gain-compensation technique is employed to realize a high-resolution /spl Sigma//spl Delta/ modulator using only low-DC-gain opamps to maximize the speed and to reduce power dissipation. On the circuit level, a fast-switching methodology is proposed for the design of the switchable opamps to achieve a switching frequency up to 50 MHz. Implemented in a 0.35-/spl mu/m CMOS process (V/sub TP/=0.82 V and V/sub TN/=0.65 V) and at 1 V supply, the modulator achieves a measured peak signal-to-noise-and-distortion ratio (SNDR) of 42.3 dB at 10.7 MHz with a signal bandwidth of 200 kHz, while dissipating 12 mW and occupying a chip area of 1.3 mm/sup 2/.     

Fuzzy rule-based classification of remotely sensed imagery

The purpose of this paper is to investigate the applicability of fuzzy rule-based modeling to classify a LANDSAT TM scene from 1984 of an area located in the south of Germany. Both a land cover map with four different categories and an image depicting the degree of ambiguity of the classification for each pixel is the expected output. The fuzzy classification algorithm will use a rule system derived from a training set using simulated annealing as an optimization algorithm. The results are then validated and compared with a common classification method in order to judge the effectiveness of the proposed technique. It will also be shown that the proposed method with only nine rules for four different land cover classes performs slightly better than the maximum likelihood classifier (MLC). For error assessment, the traditional error matrix and fuzzy operators have been used     

The measurement of solar array discharges in a simulated spaceenvironment

A spacecraft in a plasma builds up charge on all the dielectric surfaces and interfaces. Once the net charge exceeds the dielectric breakdown of the material, a discharge occurs. One of the more susceptible pieces of equipment is the antenna/receiver system. The radiated E-field may be strong enough to create an ambiguous signal which may be misinterpreted by the system electronics and cause a system malfunction. A technique is developed to monitor the radiated E-field of materials discharging in an electron environment, using vacuum chambers for measuring the material discharges which are made of highly reflective materials. These chambers affect the radiated E-field due to multiple reflections from the walls. The technique developed defines a method for correcting the effects caused by the measurement facilities. The methodology is: monitor the radiated E-field with a broadband dipole antenna, and digitize the radiated signal as a function of time. Determine the frequency response of the radiated E-field using an FFT algorithm. Measure the transmission and reflection characteristics of the two-port network inside the measurement chamber, and determine the impedance network from the measured E-parameters across the frequency band of interest. Transform the measured E-field frequency response through the impedance network to obtain the frequency response of the actual radiated discharge current. Find the inverse FFT of this response to obtain the actual radiated discharge current response. This technique aids in the prediction of the E-field coupling into receive antennas on-board actual satellites     

Microscopic simulation of electronic noise in semiconductormaterials and devices

We present a microscopic interpretation of electronic noise in semiconductor materials and two-terminal devices. The theory is based on Monte Carlo simulations of the carrier motion self-consistently coupled with a Poisson solver. Current and voltage noise operations are applied and their respective representations discussed. As application we consider the cases of homogeneous materials, resistors, n⁺nn ⁺ structures, and Schottky-barrier diodes. Phenomena associated with coupling between fluctuations in carrier velocity and self-consistent electric field are quantitatively investigated for the first time. At increasing applied fields hot-carrier effects are found to be of relevant importance in all the cases considered here. As a general result, noise spectroscopy is found to be a source of valuable information to investigate and characterize transport properties of semiconductor materials and devices     

Diurnal and spatial variation of xylem dielectric constant in Norway Spruce (Picea abies [L.] Karst.) as related to microclimate, xylem sap flow, and xylem chemistry

Spatial and temporal variations in vegetation dielectric properties strongly influence the microwave backscatter characteristics of forested landscapes. This paper examines the relationship between xylem tissue dielectric constant, xylem sap flux density, and xylem sap chemical composition as measured in the stems of two Norway Spruce (Picea abies [L.] Karst.) trees in the Fichtelgebirge region of Northern Bavaria, Germany. Dielectric constant and xylem sap flux were monitored continuously from June through October 1995, at several heights along the tree trunks. At the end of the measurement series, each tree was harvested, and its xylem sap extracted and analyzed to determine the concentrations of amino acids and cations. Results show that the sap flux density was correlated with vapor pressure deficit (VPD) at all heights in the stem. In contrast, the xylem tissue dielectric constant is influenced by VPD but can exhibit a significant temporal lag relative to changes in VPD. This lag varies with position along the tree trunk. The temporal variability of the dielectric constant is compared with both trees at several positions along the tree trunks. Results of xylem sap chemical analysis are presented. We show that spatial and temporal variability in the xylem tissue dielectric constant is influenced not only by water content, but by variations in xylem sap chemistry as well. This has important implications for microwave remote sensing of forested landscapes, as useful information may be acquired regarding stand physiology and water relations and where variations in dielectric properties within individual trees and across geographic areas can be significant error sources for forest inventory mapping.     

Effect of phonon scattering from neutral and charged impurity centers on the lattice heat conductivity of PbTe:(Tl, Na)

Experimental data on the effect of thallium and sodium impurities on the lattice heat conductivity of PbTe at room temperature are reported. Because the lattice of lead chalcogenides is strongly polarized near charged impurities, the effect of impurities on the lattice heat conductivity depends substantially on their charge state. This property of the material has been used to determine the charge state of the thallium impurity in PbTe. The results obtained argue for a model of quasi-local thallium-impurity states which assumes low electron-correlation energy at an impurity center. Fiz. Tverd. Tela (St. Petersburg) 40, 1206–1208 (July 1998)     

Current-mode A/D converter

The authors report the design of a new current-mode A/D converter, based on a modified successive-approximations model, in 1.2 μm CMOS technology. The proposed circuit is characterised by good accuracy and fast dynamic performance, low power consumption and small occupation area. SPICE simulations allow the design approach to be validated and the electrical performance of the ADC to be predicted     

Filter matrix estimation in automated DNA sequencing

In four-color fluorescence-based automated DNA sequencing, a 4×4 filter matrix parameterizes the relationship between the dye-intensity signals of interest and the data collected by an optical imaging system. The filter matrix is important because the estimated DNA sequence is based on the dye intensities that can only be recovered via inversion of the matrix. Here, the authors present a calibration method for the estimation of the columns of this matrix, using data generated through a special experiment in which DNA samples are labeled with only one fluorescent dye at a time. Simulations and applications of the method to real data are provided, with promising results