Interfacial effects on stress distribution in model composites

Raman mechanical spectroscopy was used to examine interfacial effects on the stress distribution in model polydiacetylene fiber/epoxy composites. Epoxy release agents were coated on fiber surfaces to modify the interfacial adhesion properties. The modified fiber surfaces were then characterized by scanning electron microscopy and x-ray photoelectron spectroscopy as well as optical microscopy. No difference in the maximum stress value or stress distribution was observed for the two types of fibers, coated or uncoated, used in composites. This suggests that adhesion properties at the composite interface do not affect tensile stress transfer efficiency nor, therefore, the composite tensile modulus along the fiber axis direction in uniaxial composites. Experimental data were also compared with theoretical calculations assuming perfect bonding between fiber and matrix, and idealized frictional force transfer mechanism at the fiber–matrix interface.     

Plasma immersion ion implantation for SOI synthesis: SIMOX and ion-cut

We have demonstrated feasibility to form silicon-on-insulator (SOI) substrates using plasma immersion ion implantation (PIII) for both separation by implantation of oxygen and ion-cut. This high throughput technique can substantially lower the high cost of SOI substrates due to the simpler implanter design as well as ease of maintenance. For separation by plasma implantation of oxygen wafers, secondary ion mass spectrometry analysis and cross-sectional transmission electron micrographs show continuous buried oxide formation under a single-crystal silicon overlayer with sharp Si/SiO₂ interfaces after oxygen plasma implantation and high-temperature (1300°C) annealing. Ion-cut SOI wafer fabrication technique is implemented for the first time using PIII. The hydrogen plasma can be optimized so that only one ion species is dominant in concentration and there are minimal effects by other residual ions on the ion-cut process. The physical mechanism of hydrogen induced silicon surface layer cleavage has been investigated. An ideal gas law model of the microcavity internal pressure combined with a two-dimensional finite element fracture mechanics model is used to approximate the fracture driving force which is sufficient to overcome the silicon fracture resistance.     

“J—646”新型光学光敏胶胶合工艺简介

“J—646”光敏胶具有透光率好,收缩率小,粘接强度适中,耐老化,毒性小和成本低廉等特点。本文简要介绍了该胶的胶合工艺。     

不同激发密度下CdS晶体的光致发光和受激发射

本文主要研究在77-111K温度范围内、不同激发密度的N2激光器的337.1nm谱线激发下,激子-激子(Ex-Ex)、激子-载流子(Ex-e)的相互作用和发射一个LO声子(Ex-1LO)、两个LO声子(Ex-2LO)的自由激子的辐射复合行为.并在77K温度下观测到由Ex-Ex发射产生的受激发射.     

金催化化学发光新体系——苯并吡喃化学发光分析法测定金矿中的痕量金

本文提出了一种测定矿样中痕量金的化学发光分析法,氯化6,7-二羟基-2,4-二甲基苯并吡喃-H_2O_2化学发光体系,方法的检出限为7ppb。工作曲线线性范围是10～1000ppbAu,测定的相对标准偏差小于7％。应用本法测定矿样中的金,结果良好。     

Watermarking for intellectual property protection

A new watermarking method for intellectual property (IP) protection is presented. The proposed method uses a uniquely generated stream of bits, known as a watermark, embedded into the self-test circuit to represent ownership. This scheme can detect the ownership rights of the IP provider even when the chip has been packaged. Experimental results show the proposed embedding technique can survive synthesis, placement and routing. The experimental results are given to demonstrate the proposed method.     

Structure and mechanical properties of Al/AlN multilayer with different AlN layer thickness

Nanometer scale Al/AlN multilayers have been prepared by dc magnetron sputtering technique with a columnar target. A set of Al/AlN multilayers with the Al layer thickness of 2.9 nm and the AlN layer thickness variation from 1.13 to 6.81 nm were determined. Low angle X-ray diffraction (LAXRD) was used to analyze the layered structure of multilayers. The phase structure of the coatings was investigated with grazing angle XRD (GAXRD). Mechanical properties of these multilayers were thoroughly studied using a nanoindentation and ball-on-disk micro-tribometer. It was found that the multilayer hardness and reduced modulus showed no strong dependence on the AlN layer thickness. Al2.9 nm/AlN1.13 nm multilayer had more excellent tribological properties than single layers and other proportion multilayers with a lowest friction coefficient of 0.15. And the tribological properties of all the multilayers are superior to the AlN single layer.