Component-relevancy and characterization results in multistatesystems

Two new versions of component relevancy for multistate structure functions are introduced. They are compared with some existing component-relevance conditions and their general properties are investigated. Based on the two relevance conditions, two component-importance measures for multistate systems are defined; they are most appropriate for comparing components when a certain type of system improvement is considered. Series and parallel structures are characterized within the L-superadditive and L-subadditive structure functions by imposing the two new relevance conditions     

Improved spacer design and cost reduction in an electrodialysis system

In electrodialysis using thin membranes and spacers, the compactness of the membrane cell-pairs leads to a small potential drop, and hence to energy saving. The spacer design itself has a great effect on the cost of the plants, since spacers act as turbulence promoters. A careful design, to increase the mass transfer coefficients, can reduce the membrane surface area required for a given application. Limiting current measurements, cell-pair resistance and pressure losses are presented for several thin spacers, for different flow-velocity values and feed water concentrations. It was possible to find an advantageous geometry of the separating mesh leading to substantial savings on investment and operation costs.     

Studies of the compositions of Pd(II) hydrolysis products

The characterization of the clusters formed on alkaline hydrolysis of [PdCl₄]^2– was performed using¹⁷O,²³Na,³⁵Cl,¹³³Cs NMR and UV spectroscopy. The chemical composition of the clusters was found to be [Pd(OH)₂] _n ·nNaCl. No mononuclear oxo- or hydroxocomplexes were detected. The spatial structure of the clusters is stabilized by alkali metal cations.Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 4, pp. 675–679, April, 1993.     

Solving ML equations for 2-parameter Poisson-process models forungrouped software-failure data

Existence conditions are given for maximum likelihood (ML) parameter estimates for several families of 2-parameter software-reliability Poisson-process models. For each such model, the ML equations can be expressed in terms of one equation in one unknown. Bounds are given on solutions to these one equation problems to serve as initial intervals for search algorithms like bisection. Uniqueness of the solutions is established in some cases. Solutions are also tabulated for certain simple cases. Results are given for ungrouped failure data (exact times are available for all failures). ML estimation problems for such a situation are treated as limiting cases of problems based on failure times grouped into intervals of decreasing mesh     

Magnetometer spacing criterion for biomagnetic source currentimaging

A criterion for determining the maximum spacing between magnetometers for measuring the magnetic field is derived. A two-dimensional (2-D) filter model is employed to determine the maximum spatial frequency component present in the magnetic field that is above the spectral noise level. This maximum frequency component is then sampled at a rate greater than twice per period as indicated by the Nyquist criterion, yielding the required magnetometer spacing. It is shown that the rule-of-thumb employed in current clinical biomagnetic array systems, that the spacing between the coils should be approximately equal to the depth of the source, is adequate when the signal-to-noise power ratio is less than 28.4 (14.5 dB). The analysis also quantitatively demonstrates that reducing the separation between the measurement and source planes has a greater effect on the resolution than decreasing the noise level by the same factor. This result is important for employing high T_c superconductor magnetometers that allow thinner thermal insulating layers at the cost of higher thermal noise     

A comparison of two conformal methods for FDTD modeling

Two conformal finite-difference time-domain (FDTD) methods are considered, the contour path (CPFDTD) method of Jurgens et al. (see IEEE Trans. Antennas Propagat., vol.40, p.357, 1992) and the overlapping grid (OGFDTD) method of Yee et al. (see IEEE Trans. Antennas Propagat., vol.40, p.1068, 1992). Both TE and TM scattering from a two-dimensional (2-D), perfectly conducting circular cylinder are used to test the accuracy of the methods for curved surfaces. Also, TE and TM scattering from a 2-D, perfectly-conducting rotated square cylinder are used to test the accuracy for corners and edges. It is shown that the conformal method proposed by Yee et al. provide significant improvement in accuracy over the original FDTD algorithm for most of the geometries studied. However, implementation becomes more difficult as the geometries become more complex. The conformal method proposed by Jurgens et al. provide significant improvement in accuracy as well for most of the geometries studied. However, improvement does not occur for the TM case when the square cylinder is not aligned properly with the grid. Implementation of the CPFDTD method is relatively straightforward. For the majority of the cases studied, the OGFDTD method is more accurate than the CPFDTD method     

Tunable wavelength filters based on nonlinear optical interactionsin semiconductor amplifiers

A novel class of narrow-band tunable wavelength filters is proposed and evaluated. Wavelength selectivity of the proposed filters Is derived from the finite time response of an optical nonlinearity. The nonlinearity is gain saturation in semiconductor optical amplifier structures. The filters are shown to have very narrow passbands tunable over the entire semiconductor gain bandwidth. The key to filter implementation is a device configuration in which the wave-mixing products can be isolated from the amplified inputs. Three integrated optics compatible configurations are considered and shown to have high filter throughputs 34 to 180% and subangstrom bandwidths     

New concept for applying edge line phase-shifting masks to arbitrary mask layouts

This paper explains the principle of a method which avoids printing of phantom resist lines due to undesired intensity minima appearing on Cr-less edge line phase-shifting masks. The method combines principles of grey-tone lithography and attenuated phase-shifting masks to give, what we call, a Cr-Less Attenuated Phase-shifting mask (CLAP). Rules for generating a CLAP design and a paradigm setup of a CLAP mask are presented. The capabilities and possible limitations of the CLAP method based on simulated results for a standard wafer stepper setup using the SOLID lithography simulator are being assessed.