AIRS/Vis near IR instrument

A component of the Atmospheric Infrared Sounder (AIRS) instrument system is the AIRS/Visible Near InfraRed (Vis/NIR) instrument. With a nadir ground resolution of 2.28 km and four channels, the Vis/NIR instrument provides diagnostic support to the infrared retrievals from the AIRS instrument and several research products, including surface solar flux studies. The AIRS Vis/NIR is composed of three narrowband (channel 1: 0.40-0.44 /spl mu/m; channel 2: 0.58-0.68 /spl mu/m, and channel 3: 0.71-0.92 /spl mu/m) and one broadband (channel 4: 0.49-0.94 /spl mu/m) channel, each a linear detector array of nine pixels. It is calibrated onboard with three tungsten lamps. Vicarious calibrations using ground targets of known reflectance and a cross-calibration with the Moderate Resolution Imaging Spectroradiometer (MODIS) augment the onboard calibration. One of AIRS Vis/NIR's principal supporting functions is the detection of low clouds to flag these conditions for atmospheric temperature retrievals. Once clouds are detected, a cloud height index is obtained based on the ratio (channel 2 - channel 3)/channel 1 that is sensitive to the partitioning of water vapor absorption above and below clouds. The determination of the surface solar radiation flux is principally based on channel 4 broadband measurements and the well-established relationship between top-of-the atmosphere (broadband) radiance and the surface irradiance.     

Experimental and numerical assessment of gate-lag phenomena in AlGaAs-GaAs heterostructure field-effect transistors (FETs)

Gate-lag effects are characterized in AlGaAs-GaAs heterostructure field-effect transistors (HFETs) by means of measurements and numerical device simulations. Gate lag increasingly affects device switching at increasing ungated recess extension, suggesting that responsible deep levels be located at the ungated, recess surface of the HFET. Gate lag diminishes by making the off-state gate-source voltage less negative and by increasing the drain bias. Increasing the temperature makes the turn-on transient faster at low drain bias, while slightly delaying it at high drain bias. Numerical device simulations accounting for acceptor-like traps at the ungated surface predict gate-lag phenomena in good agreement with experiments, reproducing correctly the observed bias and temperature dependences. Simulations show that surface states behave, during the turn-on transient, as hole traps capturing holes attracted at the ungated surface by the negative trapped charge.     

A New Hand-Held Microsystem Architecture for Biological Analysis

This paper presents a hand-held microsystem based on new fully integrated magnetoresistive biochips for biomolecular recognition (DNA hybridization, antibody antigen interaction, etc.). Magnetoresistive chip surfaces are chemically treated, enabling the immobilization of probe biomolecules such as DNA or antibodies. Fluid handling is also integrated in the biochip. The proposed microsystem not only integrates the biochip, which is an array of 16times16 magnetoresistive sensors, but it also provides all the electronic circuitry for addressing and reading out each transducer. The proposed architecture and circuits were specifically designed for achieving a compact, programmable and portable microsystem. The microsystem also integrates a hand-held analyzer connected through a wireless channel. A prototype of the system was already developed and detection of magnetic nanoparticles was obtained. This indicates that the system may be used for magnetic label based bioassays     

Injection-locked Fabry-Pe/spl acute/rot laser with electronic feedback for clock recovery from high-speed OTDM signals

We demonstrate the use of an injection-locked Fabry-Pe/spl acute/rot laser diode with electronic feedback for base-rate clock recovery in N/spl times/10 Gb/s optical time-division-multiplexing (OTDM) systems. Injection-locking enhances the resonance frequency of the laser and the electrical feedback achieves strong resonance at the base-rate frequency of the injected data streams, enabling ultrastable electrical clock signal generation at the base rate of 10 GHz. Experimental demonstrations for clock recovery at 10 GHz from 40-Gb/s OTDM data streams and 4-1 demultiplexing of the data using the extracted clock after fiber transmission is presented. The timing jitter measured in the recovered electrical clock is less than 0.25 ps.     

High Power Fiber Bundle Array Coupled LDA Module

1 Introduction High power laser diode arrays (LDA) have many advan- tages such as small volume, long working life, high slope efficiency and high optical density, so they have many applications in medical treatment, material pro- cessing, and for the pumping source of solid laser and etc. But unfortunately, the LDA can not be easy to use directly in these fields because of their poor beam quality and extremely asymmetric divergent beams (!x≈ 5°～10°and !y≈20°～35°, for example), so it …     

A tree partitioning dynamic policy for OVSF codes assignment in wideband CDMA

This paper proposes some novel techniques to accommodate users with different rate requirements in a wideband code-division multiple-access system employing orthogonal variable spreading factor codes. Two simple static code assignment strategies are first considered, and an improvement based on multicode assignment. Then the new idea of tree partitioning is introduced and used to devise a dynamic code reassignment algorithm. The behavior of these different techniques is experimentally investigated, in terms of call blocking probability and number of required reassignments. The tree partitioning method exhibits very good performances.     

Laterally coupled buried heterostructure high-Q ring resonators

All-buried InP-InGaAsP ring resonators laterally coupled to bus waveguides are demonstrated. The buried configurations offer a lower built-in refractive index step along the resonator periphery, which affords enhanced optical coupling coefficients between the waveguides and reduced scattering losses caused by the resonator sidewall imperfections. Very low optical intensity attenuations of 0.4 cm/sup -1/ and coupling-limited quality factors of greater than 10/sup 5/ are observed from 200-/spl mu/m-radii ring resonators. The measured spectral linewidth is as narrow as 0.0145 nm.     

Control system design on a power-split CVT for high-power agricultural tractors

The problem considered in this paper is the design and tuning of the control system of a power-split continuously variable transmission (CVT) used in high-power tractors. Power-split CVTs are characterized by the combination of a traditional mechanical transmission and by a continuously-variable transmission. This guarantees, at the same time, smooth variations of the transmission-ratio and high efficiency of the overall transmission system. The control architecture of an hydrostatic power-split CVT is constituted by three main parts: 1) servo-controller on the current of the valve which drives the hydraulic transmission; 2) a servo-controller on the hydraulic transmission-ratio; and 3) a synchronizer which coordinates the hydraulic and the mechanical parts of the CVT. In this work, these three controllers are fully developed, including: design, implementation, and evaluation on an experimental system.     

Optical intensity-modulated direct detection channels: signal space and lattice codes

Traditional approaches to constructing constellations for electrical channels cannot be applied directly to the optical intensity channel. This work presents a structured signal space model for optical intensity channels where the nonnegativity and average amplitude constraints are represented geometrically. Lattice codes satisfying channel constraints are defined and coding and shaping gain relative to a baseline are computed. An effective signal space dimension is defined to represent the precise impact of coding and shaping on bandwidth. Average optical power minimizing shaping regions are derived in some special cases. Example lattice codes are constructed and their performance on an idealized point-to-point wireless optical link is computed. Bandwidth-efficient schemes are shown to have promise for high data-rate applications, but require greater average optical power.     

Experimental real-time detector of GSM terminals

The authors present an experimental real-time GSM terminal detector, to be installed in a restricted area. The detector triggers terminal signaling, which can be captured.