A universal matrix solver for integral-equation-based problems

A new method has been developed for compressing the matrices that occur in most integral-equation-based computer programs. This method is easy to interface with existing computer programs, and allows them to run significantly faster and with significantly less memory. This method applies not only to electromagnetic and acoustic computation, but also to most programs involving a Green's function or any integral equation with a kernel having some smoothness properties. Our numerical computations, running on a high-end personal computer, have achieved compression ratios of fifty times, and compressed inversion of the matrices fifty times faster than by previous methods. For larger problems, solved on high-performance computers, these ratios would improve to about one thousand to one for larger moment method problems.     

A simple impulsiveness correction factor for control of electromagnetic interference in dynamic wireless applications

The emerging software defined radio technologies will be an enabler for a new generation of dynamic wireless systems. It will also open up the possibility of allocating frequencies in a, more dynamic way than today. From an intersystem-interference point of view, this can cause unforeseen problems to occur due to the increased complexity in such applications. In such applications, a measure indicating whether or not a frequency band is possible to use from an electromagnetic interference point of view, must be found. A simple approach is to use the measured total average interference power within the receiver band. Since the interference impact on modern digital communication systems from an interference signal does not only depend on the power but also on the actual waveform of the interference signal, some kind of quality measure of the average-power approach would be convenient to use. In this paper, we introduce a simple quality measure of the average-power approach so that a rough adjustment for the interference-waveform properties can be done.     

Waveguide probe structures for a multilayer magnetodielectric: An inverse problem

Direct and inverse problems are considered for diffraction by an open end of a rectangular waveguide (RW) with a flange that adjoins a piecewise inhomogeneous planar layered lossy medium. Also considered are similar diffraction problems for a junction of an RW and a rectangular resonator filled with a multilayer medium and a junction of two RWs, one of which contains a multilayer plate. Such open and shielded waveguide probe structures (WPSs) are used for determination and nondestructive testing of parameters of multilayer samples. The direct problem is formulated on the basis of admittance and impedance algorithms with consideration for losses existing in the medium, flange, and screens. In this case, the approximation of the given aperture field allows obtainment of explicit solutions for open and shielded WPSs in the form of integrals. Solution of the inverse problem that lies in determining thicknesses, permittivities, and permeabilities of the layers from measured values of the magnitude of the reflection coefficient is obtained by minimizing the corresponding least-squares error and by constructing artificial neural networks. In order to increase the accuracy, it is proposed to use a two-port of errors and perform measurements for several positions of the sample with respect to the flange and different impedance conditions behind the sample.     

The colored revolution of bioimaging

This paper provides an overview of the main aspects of modern fluorescence microscopy. It covers the principles of fluorescence and highlights the key discoveries in the history of fluorescence microscopy. The paper also discusses the optics of fluorescence microscopes and examines the various types of detectors. It also discusses the signal and image processing challenges in fluorescence microscopy and highlights some of the present developments and future trends in the field.     

Self-oscillating dimmable electronic ballast

This paper presents a simple alternative for an electronic ballast operating in self-sustained oscillating mode with dimming capability for fluorescent lamps. A simple modification in one of the gate drivers side circuit allows the lamp to dim without compromising the simplicity, reliability, and low cost which characterize the self-oscillating electronic ballast (SOEB). A qualitative analysis is presented to explain the behavior of the proposed self-oscillating electronic ballast with dimming feature. In addition, the stability and the key equations for the design are derived using the extended Nyquist criterion and describing function method. Experimental results from two 40-W electronic ballasts are presented to demonstrate the performance and to validate the analysis carried out.     

Transient response of ARROW VCSELs under external optical feedback

The effect of external optical feedback on the transient response of antiresonant reflecting optical waveguide (ARROW) vertical-cavity surface-emitting lasers (VCSELs) is studied. It can be shown that the proper design of ARROW can suppress the excitation of high-order transverse leaky mode as well as increase the critical feedback strength so that stable high-power single-mode operation of VCSELs can be obtained even under the influence of strong external optical feedback.     

The LHC pre-series dipole cold mass geometry

In order to provide the necessary mechanical aperture for the LHC beam, the main dipole cold masses have to match precisely the nominal circular trajectory of the particles beam. The requirements on the dipole cold mass geometry are dictated by the LHC beam optics and by the allowed limits of mechanical deformation of the interconnection bellows. Keeping the tight tolerances that are imposed necessitates a well controlled bending process and the use of a high accuracy 3D measuring instrument for checking the geometry of the cold mass throughout many manufacturing stages up to the final inspection. The dipole cold mass pre-series production started in 2000. It is almost completed at the three sites. In this paper, we report on the problems encountered to shape correctly the cold masses, their effect on interconnection of the dipole cold masses and on the mechanical aperture. On one side measures to improve the production process in terms of accuracy and reproducibility were taken, on the other side the assembly tolerances could be relaxed following a thorough review of the machine requirements. The summary of the encountered problems, corrective actions and results obtained on the pre-series cold masses are presented and discussed.     

Structured low-density parity-check codes

This article describes the different methods to design regular low density parity-check (LDPC) codes with large girth. In graph terms, this corresponds to designing bipartite undirected regular graphs with large girth. Large girth speeds the convergence of iterative decoding and improves the performance at least in the high SNR range, by slowing down the onsetting of the error floor. We reviewed several existing constructions from exhaustive search to highly structured designs based on Euclidean and projective finite geometries and combinatorial designs. We describe GB and TS LDPC codes and compared the BER performance with large girth to the BER performance of random codes. These studies confirm that in the high SNR regime these codes with high girth exhibit better BER performance. The regularity of the codes provides additional advantages that we did not explore in this article like the simplicity of their hardware implementation and fast encoding.     

Three takes on telecom's troubles

Spectrum asked three IEEE members from the telecommunications sector to comment on the industry's current woes and prospects. Roch Guerin discusses bandwidth as a commodity and how to deal with it. The impact of technological change on telecommunications is enormous and calls for a shift in business models. Technology is making bandwidth a commodity and it should not matter who supplies it. Competition is vital and commodity providers must be decoupled from value providers. Frank Ferrante points out that the Year 2000 crisis resulted in manufacturers being deluged with orders for new upgraded systems. Vast sums were spent to meet the demand in time. However, when Y2K was over, production stayed high and inventories continued to build, while demand effectively stopped overnight. Dazzling new innovations are needed to compel the masses to spend and manufacturers must apply their resources to deliver quickly and efficiently. Jules A. Bellisio discusses the role of engineers in bringing new ideas to the market place. Many engineers have put together ventures for the sole purpose of attracting capital. The underlying technology and business propositions were there solely to lure the unsuspecting. By allowing engineers to use technology simply to cover for a scam, then the profession is also to blame for the current problems.