Effect of Fog and Clouds on the Image Quality in Millimeter Communications

The effect of fog and clouds in millimeter communication is discussed, and the attenuation caused by fog and clouds is reviewed. Signal-to-noise ratio (SNR) of image is derived using relating models of fog and clouds attenuation. According to the relation of image quality and its signal-to-noise ratio, the system behavior is forecasted theoretically. It is shown that the signal-to-noise ratio of receiver at certain transmitter power is inverse with radio wave frequency, from about 70dB at 10GHz to 48dB for fog and 49dB for clouds. The image quality of received signal at certain transmitter power is inverse with radio wave frequency, from about 7 grade at 10GHz to 5.27 grade for fog and 5.37 grade for clouds. The above calculated results are consistent with experimental results.     

Evanescently coupled photodiodes integrating a double-stage taper for 40-Gb/s applications-compared performance with side-illuminated photodiodes

The design, fabrication, and performance of double-stage taper photodiodes (DSTPs) are reported. The objective of this work is to develop devices compatible with 40-Gb/s applications. Such devices require high efficiency, ultrawide band, high optical power handling capability, and compatibility with low-cost module fabrication. The integration of mode size converters improves both the coupling efficiency and the responsivity with a large fiber mode diameter. Responsivity of 0.6 A/W and 0.45 A/W are achieved with a 6-/spl mu/m fiber mode diameter and cleaved fiber, respectively, providing relaxed alignment tolerances (/spl plusmn/1.6 /spl mu/m and /spl plusmn/2 /spl mu/m, respectively), compatible with cost-effective packaging techniques. DSTPs also offer a wide bandwidth greater than 40 GHz and transverse-electric/transverse-magnetic polarization dependence lower than 0.2 dB. Furthermore, a DSTP saturation current as high as 11 mA results in optical power handling greater than +10 dBm and a high output voltage of 0.8 V. These capabilities allow the photodiode to drive the decision circuit without the need of a broad-band electrical amplifier. The DSTP devices presented here demonstrate higher responsivities with large fiber mode diameter and better optical power handling capabilities and are compared with classical side-illuminated photodiodes.     

热作模具钢表面激光堆焊耐磨合金层的研究

本文主要通过在H13钢上用大功率CO_2激光束进行堆焊,阐述了激光堆焊工艺变化对堆焊组织和性能的影响,在本试验条件下,得到了高密度弥散金属化合物组织的激光堆焊层,平均硬度为HV800,与基体呈冶金结合,耐磨性比H13模具钢提高149%。     

Quantisation noise control in perceptual audio coding using low selectivity filter banks

The problem of computing, in a subband audio coder, the maximum quantisation noise power that can be injected in each band to ensure transparent coding when low selectivity filter banks are used, is addressed. A low complexity strategy, taking into account the frequency responses of the synthesis filter bank, is proposed for achieving an overall distortion due to quantisation noise always below the masking threshold (provided by a psycho-acoustic model) for any length prototype filters.     

An optical instrumentation using a sensor with a sensordummyagainst noises on sensor and transmission line

This short paper discusses the method of effectively canceling equal status normal mode noise not only on a sensor line but also on a transmission line of an optical instrument using a sensor with a sensordummy resistance     

1/f noise sources

This survey deals with 1/f noise in homogeneous semiconductor samples. A distinction is made between mobility noise and number noise. It is shown that there always is mobility noise with an α value with a magnitude in the order of 10^-4. Damaging the crystal has a strong influence on α, α may increase by orders of magnitude. Some theoretical models are briefly discussed none of them can explain all experimental results. The α values of several semiconductors are given. These values can be used in calculations of 1/f noise in devices     

Correlation of modified crack tip opening distance with heat input to the heat affected zone of high-strength low-alloy steels

Investigated is the dependency of the crack tip opening displacement (CTOD) on the local microstructure of the heat affected zone in high-strength low-alloy (HSLA) microalloyed steel. Since the initiation of the crack tip location could not be controlled in fatigue, any possible correlation between heat iput in welding and fracture toughness could be smeared. Modified CTOD data are defined; they show that the fracture resistance of the weld joint decreased as the heat input increased.     

T1Effects in Sequential Dynamic Susceptibility Contrast Experiments

Residual effects of an initial bolus of gadolinium contrast agent have been previously demonstrated in sequential dynamic susceptibility contrast MR experiments. While these residual effects quickly reach a saturation steady state, their etiology is uncertain, and they can lead to spurious estimates of hemodynamic parameters in activation experiments. The possible influence ofT₁effects is now investigated with experiments in whichT₁weighting is varied as well as with serial regionalT₁measurements. Little evidence for significant residualT₁effects is found, suggesting instead that susceptibility effects underlie these observations. An initial saturation dose of contrast agent minimizes this effect.     

Laser spectroscopy of the 1s HFS of H-like ions at a bunched beam in the storage ring ESR

The investigation of the 1s HFS provides a good possibility for testing QED effects in a combination of a strong electric and magnetic field. Here, we report about the laserspectroscopic measurements of the ground state hyperfine splitting in ²⁰⁷Pb⁸¹⁺. To handle this M1-transition in the infrared optical regime with its long lifetime, we developed a new detection technique using a bunched ion beam. For the observation of fluorescence light, a new mirror system is adapted to the emission characteristics from an ion beam at relativistic velocities. This revised version was published online in July 2006 with corrections to the Cover Date.     

氢化丁苯共聚物结构的核磁共振波谱表征Ⅱ.微观结构的定量计算

在氢化丁苯共聚物¹³C-NMR谱脂肪碳部分谱带归属的基础上,根据各谱带的主要来源,推导出六个二单元浓度的计算公式。计算出二单元、一单元的相对含量,各结构单元的数均序列长度、嵌段含量和其它结构参数。加氢前后的¹H-和¹³C-NMR谱的组成计算结果基本一致。初步探讨了作为粘度指数改进剂的氢化丁苯共聚物微观结构与性能的关系,为合成提供了依据。