Colloidal processing of polymer ceramic nanocomposite integral capacitors

Polymer ceramic composites form a suitable material system for low temperature fabrication of embedded capacitors appropriate for the MCM-L technology. Improved electrical properties such as permittivity can be achieved by efficient filling of polymers with high dielectric constant ceramic powders such as lead magnesium niobate-lead titanate (PMN-PT) and barium titanate (BT). Photodefinable epoxies as the matrix polymer allow fine feature definition of the capacitor elements by conventional lithography techniques. The optimum weight percent of dispersant is tuned by monitoring the viscosity of the suspension. The dispersion mechanism (steric and electrostatic contribution) in a slightly polar solvent such as propylene glycol methyl ether acetate (PGMEA) is investigated from electrophoretic measurements. A high positive zeta potential is observed in the suspension, which suggests a strong contribution of electrostatic stabilization. By optimizing the particle packing using a bimodal distribution and modified processing methodology, a dielectric constant greater than 135 was achieved in PMN-PT/epoxy system. Suspensions are made with the lowest PGMEA content to ensure the efficiency of the dispersion and efficient particle packing in the dried film. Improved colloidal processing of nanoparticle-filled epoxy is a promising method to obtain ultra-thin capacitor films (<2/spl mu/m) with high capacitance density and improved yield. Capacitance of 35 nF/cm/sup 2/ was achieved with the thinnest films (2.5-3.0 /spl mu/m).     

Hf-doped and NH/sub 3/-nitrided high-K gate dielectric thin film with least drain current degradation and flatband voltage shift

A novel technique to form high-K dielectric of HfSiON by doping base oxide with Hf and nitridation with NH/sub 3/, sequentially, is proposed. The HfSiON gate dielectric demonstrates excellent device performances such as only 10% degradation of saturation drain current and almost 45 times of magnitude reduction in gate leakage compared with conventional SiO/sub 2/ gate at the approximately same equivalent oxide thickness. Additionally, negligible flatband voltage shift is achieved with this technique. Time-dependent dielectric breakdown tests indicate that the lifetime of HfSiON is longer than 10 years at V/sub dd/=2 V.     

Reliability investigation of 0.07-/spl mu/m InGaAs-InAlAs-InP HEMT MMICs with pseudomorphic In/sub 0.75/Ga/sub 0.25/As channel

The authors have investigated the reliability performance of G-band (183 GHz) monolithic microwave integrated circuit (MMIC) amplifiers fabricated using 0.07-/spl mu/m T-gate InGaAs-InAlAs-InP HEMTs with pseudomorphic In/sub 0.75/Ga/sub 0.25/As channel on 3-in wafers. Life test was performed at two temperatures (T/sub 1/ = 200 /spl deg/C and T/sub 2/ = 215 /spl deg/C), and the amplifiers were stressed at V/sub ds/ of 1 V and I/sub ds/ of 250 mA/mm in a N/sub 2/ ambient. The activation energy is as high as 1.7 eV, achieving a projected median-time-to-failure (MTTF) /spl ap/ 2 /spl times/ 10/sup 6/ h at a junction temperature of 125 /spl deg/C. MTTF was determined by 2-temperature constant current stress using /spl Delta/G/sub mp/ = -20% as the failure criteria. The difference of reliability performance between 0.07-/spl mu/m InGaAs-InAlAs-InP HEMT MMICs with pseudomorphic In/sub 0.75/Ga/sub 0.25/As channel and 0.1-/spl mu/m InGaAs-InAlAs-InP HEMT MMICs with In/sub 0.6/Ga/sub 0.4/As channel is also discussed. The achieved high-reliability result demonstrates a robust 0.07-/spl mu/m pseudomorphic InGaAs-InAlAs-InP HEMT MMICs production technology for G-band applications.     

Panchromatic Chromophore Mixtures in an AlPO4‐5 Molecular Sieve: Spatial Separation Effects and Energy Transfer Cascades

Dye‐loaded AlPO₄‐5 single crystals were prepared by microwave‐assisted hydrothermal synthesis from a batch, containing a mixture of three chromophores (Coumarin 40, Rhodamine BE50, and Oxazine 1) differing in their absorption range, molecular dimensions, and solubilities. Confocal fluorescence images reveal a spatial separation effect of the dye molecules, where the slimmer, more‐soluble dye molecule (Coumarin 40) is uniformly distributed in the body of the single crystal, and the bulky and/or less‐soluble ones (Rhodamine BE50, Oxazine 1) are situated in distinct domains. Visible spectra show good panchromatic absorption of visible light. Fluorescence lifetime measurements indicate the presence of an energy transfer cascade of the entirely fixed dye molecules from Coumarin 40 to Oxazine 1. The transfer mechanism is predominantly radiative.     

Thermal conductivity of doped PbTe-based solid solutions with off-center impurities

The coefficients of thermopower and electrical and thermal conductivity in the PbTe_0.8Se_0.1 S _0.1 solid solution with electron concentration (4.6–54) × 10¹⁸ cm^?3 are studied in the range of 85–300 K (and in some cases up to 700 K). The temperature dependences of electrical and thermal conductivity indicate that the low-temperature electron and phonon scattering initiated by the off-center impurity of sulfur exists. The temperature dependences of the electronic and lattice components of thermal conductivity are calculated in the approximation of a parabolic spectrum and electron scattering by acoustic phonons and neutral substitutional impurities. The lattice thermal conductivity is found to have a feature in the form of a shallow minimum in the range of 85–250 K. A similar feature, while not so clearly pronounced, is found to exist also in Pb_1?x Sn_xTe_1?x Se_x alloys (x≥0.15) with an off-center tin impurity. An analysis of the possible origins of this effect suggests that, at low temperatures, the Lorentz numbers L of the materials under study are smaller than the L₀ numbers employed which correspond to the above scattering mechanisms. The cause of the decrease in L is related to electron scattering at two-level systems, a mechanism whose effect grows with increasing electron energy. An analysis of experimental data obtained at high temperatures, as well as on undoped samples with the lowest possible carrier concentrations, yields the values of L for samples with different electron densities. The minimum value L/L₀ = 0.75 is obtained for a lightly doped sample at ～130 K.     

Photoemission of polarized electrons from InAlGaAs/GaAs superlattices with minimum conduction band offsets

Photoemission of polarized electrons from heterostructures based on InAlGaAs/GaAs superlattices with minimum conduction-band offsets is investigated. The comparison of the excitation energy dependence of the photoemission polarization degree with the calculated spectra make it possible to determine the polarization losses at different stages of the photoemission. A maximum polarization of P = 91% and a quantum yield of 0.14% are close to the best results obtained for photocathodes on the basis of strained semiconductor superlattices.     

A military perspective on small unmanned aerial vehicles

In recent years, advancements in three technology areas, microelectronics, MEMS sensors, and GPS receivers, have allowed small UAVs to overcome critical deficiencies and become practical for insertion into the military mainstream. The maturation and commercialization of these technologies have resulted in readily available components that have decreased in both size and cost, to the point where truly low-cost, highly capable, small UAVs are possible. In particular, inertial devices such as MEMS accelerometers and angular rate sensors, pressure sensors, and magnetometers have reached the point where they are reliable, accurate, and affordable. These devices allow the determination of vehicle state with the precision required to enable autonomous flight. In addition, advanced microelectronic devices, such as digital signal processors, field programmable gate arrays, and microcontrollers have enabled sophisticated flight control functions, including fully autonomous flight using GPS waypoints. In combination, these advances have allowed small UAVs such as Pointer, Raven, and Dragon Eye to move into full-scale production and continue to allow the progression of UAVs into smaller and smaller packages. To address several of the deployment issues connected with small UAVs, a gun-launched version, along with the underpinning technologies, is under development. This device represents a clear departure from conventional UAVs with several clear advantages; however, it also contains severe design challenges, as well as test and evaluation dilemmas. An option of this type is envisioned not as a replacement for conventional small UAVs but rather as an augmenting capability.     

Analytical multipoint moment matching reduction of distributed thermal networks

In this paper, the multipoint moment matching method for model order reduction of discretized linear thermal networks is extended to distributed linear thermal networks. As a result, from the analytical canonical forms of distributed linear thermal networks, reduced thermal networks are derived analytically. This direct construction of the reduced network, from the exact analytical solutions, avoids the inevitable inaccuracies inherent in conventional surface and volume meshing. It allows nearly exact reduced thermal network construction by domain decomposition for arbitrarily complicated structures.     

Injection-seeded Q-switched fiber ring laser

We present a narrow linewidth, injection-seeded Q-switched Er fiber ring oscillator, that provides over 600 /spl mu/W of average output power at 500 Hz, with 1.2 /spl mu/J per pulse, before the output appears to be significantly affected by stimulated Brillouin scattering. This laser configuration provides multiple advantages in LIDAR systems because it offers the possibility of broad and rapid tunability.