The effect of olefinic terminal chains on the mesomorphic properties of 4,4'-disubstituted diphenyldiacetylenes

New diphenyldiacetylenes of the type with A, B = H and/or F; m = 0, 1; n = 1-4; and X = C n H 2n + 1 , F, CF 3 or CN were synthesized and their mesomorphic properties determined by hot stage polarizing microscopy and DSC. When m = 0, all of these compounds showed only a nematic phase except when X = CF 3 when both nematic and smectic A phases were seen. Both clearing and melting temperatures were higher than those reported for substitution with the corresponding alkyl chains but the much larger increase in clearing temperatures produced considerably wider nematic phases. Eutectic mixtures of a few of these olefins yielded nematic materials also having much wider temperature ranges and higher clearing temperatures than the eutectic mixtures of the alkyl compounds, while retaining their high birefringence and low viscosities. Such materials are of interest for beam-steering devices.

Four of the diacetylenes with m = 1 ( A, B = H) were also prepared ( X = C 6 H 13 , F, n = 2, 3). When X was C 6 H 13 ( n = 2), the nematic range was smaller in the 2- than in the 1-olefin but wider than in the alkyl series. When X = F, either no nematic phase or a monotropic one was observed, whereas the 1-olefins gave a much wider nematic phase. Both transition temperatures were lower than those for the corresponding 1-olefin and alkyl analogues. The compound with X = C 6 H 13 and n = 2 had a melting temperature below room temperature.     

89-GHz fT room-temperature silicon MOSFETs

The authors report the implementation of deep-submicrometer Si MOSFETs that at room temperature have a unity-current-gain cutoff frequency (f_T) of 89 GHz, for a drain-to-source bias of 1.5 V, a gate-to-source bias of 1 V, a gate oxide thickness of 40 Å, and a channel length of 0.15 μm. The fabrication procedure is mostly conventional, except for the e-beam defined gates. The speed performance is achieved through an intrinsic transit time of only 1.8 ps across the active device region     

Computation of the average power pattern of a reflector antennawith random surface errors and misalignment errors

To specify manufacturing tolerances of a reflector antenna, various errors such as random surface errors and misalignment errors must be considered at one time because superposition of the effects of those errors may not hold. Based on the Rahmat-Samii's formulation (1983), a method for computing efficiently the average power pattern of a reflector antenna with those errors is presented. Simulation results show that superposition of the effects of errors does not generally hold and demonstrate how those errors degrade the peak-gain and sidelobe levels     

Preparation of enantiomerically pure (R)-2-butyryloxymethylglycidol by lipase-catalyzed asymmetric hydrolysis

Optically active epoxy alcohol, (R)-2-butyryloxymethylglycidol3 which is the precursor of a tert-alcohol chiral building block was obtained in high enantiomeric purity, 98.7% e.e., by lipase-catalyzed asymmetric hydrolysis using a phosphate buffer and organic co-solvent system in 95% of chemical yield.     

Reduction of loading effect by tungsten etchback in a magneticallyenhanced reactive ion etcher

The plug loading effect occurring during the etchback of tungsten was investigated in a magnetically enhanced reactive ion etcher using SF ₆/Ar mixtures. It was found that while the plug loading effect is independent of varying SF₆/Ar flow rate ratio and magnetic field intensity, it is reduced under the condition of high selectivity of tungsten relative to TiN which was achieved at high chamber pressure and low RF power. It is proposed that when TiN is used as a glue layer, the W etch rate enhancement in the plug is mainly controlled by a local loading effect. Under the optimized etchback conditions the plug loss was successfully controlled without the tungsten residue left on severe topology     

Phase-insensitive all-optical transistors based on second-ordernonlinearities

We demonstrate and compare two phase-insensitive all-optical transistors (AOT's) based on frequency-degenerate quadratic three-wave interactions. In particular, we demonstrate gain using KTP in a type II geometry. Both AOT's exploit the phase insensitivity inherent to three-wave parametric processes when only two fields are input, providing amplification of a small signal at the operating frequency via the interaction with a second-harmonic wave. The first scheme is based on successive up- and down-conversion (i.e., cascading) while the second relies on parametric down-conversion. We obtain gains of 5 and 160 in the two configurations, respectively, with a significant background and output coherent to the pump in the first case, no background and coherence between output and signal in the second     

Mode analysis of DFB SE lasers

This paper presents theoretical results on mode characteristics of surface-emitting (SE) lasers utilizing an active second-order grating section. Based on a coupled-mode approach, longitudinal modes and the associated space-harmonic transverse modes are calculated via a numerical technique. From these, the lasing-mode spectrum, near- and far-field patterns of the radiation mode, and the surface-emission power efficiency are obtained. Effects of the substrate reflector and the grating parameters are also investigated. Finally, comparisons are made with conventional, edge-emitting DFB lasers. The results indicate that with a suitable choice of structural parameter values, DFB SE lasers can be made to possess both the spectral discrimination of the conventional DFB lasers and the advantages of SE lasers at the same time and also that the second lowest longitudinal mode may be preferred over the fundamental longitudinal mode for many applications due to its symmetric field distribution     

Separation of screw-sensed particles in a homogeneous shear field

The Stokes motions of three-dimensional screw-sensed slender particles in a homogeneous shear field are investigated, including the effects of buoyancy. Conclusions are drawn about the possibility of achieving a separation of mixtures of right- and left-handed particles. The linearity of the Stokes equations allows complex flows to be solved by adding the effects of the several terms which describe the flow in which the particle is immersed. The homogeneous shear flow considered here consists of three such terms; solutions for a series of 12 unit motions are sufficient to determine the hydrodynamic resistance tensors. The forces and torques experienced by screw-sensed particles are calculated from these 51 resistance tensors, using slender-filament theory. The results allow an estimate of the range of buoyancy parameters for which gravitational sedimentation can be neglected. The fundamental component of the particle motion is a rotation, at approximately the same angular velocity as that of the fluid. Superimposed on this are variations, of large period, in the particle orientation. A phase plane analysis is used to find the terminal orientations. Very long calculation times are required for the phase portrait. An approximate method based on azimuthally-averaged equations is developed to avoid the requirements for long time integration.     

Complete joint weight enumerators and self-dual codes

We define the complete joint weight enumerator in genus g for codes over /spl Zopf//sub 2k/ and use it to study self-dual codes and their shadows. These weight enumerators are related to the theta series of the associated lattices and Siegel and Jacobi forms are formed from these series.     

Validation of a method for predicting the precision, limit of detection and range of quantitation in competitive ELISA.

The mathematical model for predicting the precision, limit of detection (LOD) and range of quantitation (ROQ) in a competitive enzyme-linked immunosorbent assay (ELISA) proposed by Hayashi et al. (Anal. Chem., 2004, 76, 1295) was validated. The model describes the relative standard deviation (RSD) of concentration estimates by the RSDs of pipetting volumes of analyte, enzyme-conjugated antigen, antibody and substrate solutions, and the standard deviation (SD) of inherent absorbances between the wells in an ELISA plate. For 6 kinds of direct competitive ELISA kits, the LOD and ROQ predicted by the model agreed well with those obtained by experiments with real samples. It was also confirmed that the model is applicable to the prediction of uncertainty that depends on the pipetting error of the viscous antiserum solution. The model was demonstrated to be useful for estimating the LOD and ROQ of competitive ELISA.